Disassembly top/lang-es

From OLPC

< Disassembly top
Revision as of 05:58, 4 July 2012 by Quozl (Talk | contribs)
(diff) ← Older revision | Current revision (diff) | Newer revision → (diff)
Jump to: navigation, search
  Traducción de Disassembly_top original  
  english | español   +/- cambios  
Ahora, edita tu traducción, usando lo siguiente como guía:
[[Original page]] [[Original page/lang-es]]
(nombre de la página traducida)
Borrando el texto traducido...
(no muy recomendado)
{{OLPC}}
{{Translations}}


== Some header ==


Some text blah... 
blah... [[#Another header]]
... blah == Another header == Some other text blah...
blah... [[Another page]]
and [[Another page#section|section]]
... blah
{{OLPC}}
{{Translation
 | lang = xx
 | source = Original page
 | version = yyyy}}
{{Ongoing Translation}}

{{anchor|Some header}}
== Un titular ==

Algo de texto bla... 
bla... [[#Another header|Otro titular]]
... blah {{ Translated text | Some text blah...
blah... [[#Another header]]
... blah | display = block}} {{anchor|Another header}} == Otro titular == Algo más de texto bla...
bla... [[Another page/lang-xx|Otra página]]
y [[Another page/lang-xx#section|sección]]
... bla {{ Translated text | Some other text blah...
blah... [[Another page]]
and [[Another page#section|section]]
... blah | display = block}}
{{OLPC}}
{{Translation
 | lang = xx
 | source = Original page
 | version = yyyy}}

{{anchor|Some header}}
== Un titular ==

Algo de texto bla... 
bla... [[#Another header|Otro titular]]
... blah {{anchor|Another header}} == Otro titular == Algo más de texto bla...
bla... [[Another page/lang-xx|Otra página]]
y [[Another page/lang-xx#section|sección]]
... bla

Páginas de soporte: si hay un enlace rojo como el siguiente:

[[Original page/translations]]
[[Original page|english]]
[[Original page/lang-es|Página original]]

... debes seguirlo y pegar "{{subst:requesttranslation}}" allí:

[[Another page/lang-es]] [[Another page]]
{{subst:requesttranslation}}
Eso se sustituye con el template:
''{{Translation|lang=es|source=Another page|status=deseada}}
some untranslated page...
maybe the content is mutating rapidly,
or is peripheric to the main corpus, etc.


Contents

This is a description of how to disassemble the top portion of an XO laptop. This is part of the Disassembly section of the Troubleshooting Guide and Repair Manual.

Similar Guides

The following guides refer to disassembly of the laptop to reach a particular component:


XO before disassembly

As a precaution, remember to remove the battery.

Before we begin
Remove the battery.


Removing the front panel

Step 1

Open the laptop and flip the screen up. Rotate it a 90 degree angle as shown in the sequence below. Next, remove the screws from the bottom of the screen - there are two on each side (right/left) of the XO, so make sure to get all four.

Flip screen up
Rotate
Unscrew - remember, there are 4.


Step 2

Remove the two green panels from the side of the XO. Slide them upwards and lift them off as shown.

Slide up
Lift off


Step 3

Finally, pull off the front panel. It is tabbed, so it can simply be pulled out. Pull the bottom out (where the screws came out), and gently slide the piece downwards and out.


Removing the screen

Note that if the screen and motherboard aren't being changed, it is not necessary to actually disconnect the screen in order to access the motherboard. Follow step 1, then gently move the screen to perform the following steps (removing the back cover).

Step 1

To get the screen out, remove the four screws highlighted.

Unscrew

Step 2

Next, carefully slide the screen out, pulling the bottom out. Do not tug it or let go, as it will still be connected to the motherboard by two cables.

Slide out gently
Watch out for cables!


If you are just accessing the motherboard, not changing it or the display, do not unplug the display cables. Simply move the display to access the back cover screws behind it. With every cycle, there is a chance of damage to the display cable connectors on the motherboard.

The connectors have a black plastic bar holding the cable down. To unclamp the cable you have to lift that bar by tugging on the little tab away from the circuit board.

Unhook the cable
Watch out for this little cable, too.
Good to go!


Removing the back cover / reaching the motherboard

Step 1

Take out 4 screws
Turn over. Pull up and remove the back plate


Replacing the back cover

Step 1

Turn over. Replace the back plate.
Pick the right screw!
Turn over. Secure the back plate by putting in the four screws where indicated.


Replacing the screen

Step 1

Reattach the screen by sliding the connection cables into place and clipping them back down (it is generally easier to clip the thinner one that has a longer tether first). Reseat the screen, making sure that it sits flat and that none of the spacers are gone.

Clip little cable in
Clip big cable in


Gently slide screen back in
The screws with the large heads (4) go back in


Replacing the front panel

Step 1

Slide the front panel back on, making sure that it sits flat. Note that there are hooks on the side of the panel (highlighted in blue) that need to slide into place; pushing the top of the screen flat and sliding it upwards works well.

Watch out for these hooks
The rest of the panel slides into place


Step 2

Slide the green side pieces back into place. Then, rotate the XO 90 degrees and put the remaining screws back. Don't forget that the screws go in on both sides (right/left).

Side panels slide back in place
Almost there!


Rotate
Put screws (4) back in.


Personal tools
  • Log in
  • Login with OpenID
About OLPC
About the laptop
About the tablet
Projects
OLPC wiki
Toolbox
In other languages