Talk:Power peripherals/Bicycle Powered Generator: Difference between revisions
Jump to navigation
Jump to search
(New page: ==Bicycle Generator== ===Introduction=== A bicycle generator can be a very efficient, inexpensive and easy to construct method for powering the XO laptop. Under such a setup, a stationary ...) |
(Removing all content from page) |
||
Line 1: | Line 1: | ||
==Bicycle Generator== |
|||
===Introduction=== |
|||
A bicycle generator can be a very efficient, inexpensive and easy to construct method for powering the XO laptop. Under such a setup, a stationary bike is connected to either a permanent magnet DC motor or a car or truck alternator which outputs a certain amount of power to the laptop. A human being pedaling at a comfortable cadence can produce more than 50W continuously for over an hour without tiring, and wattage output much higher than this can easily be achieved. A trained cyclist can put out as many as 200W for a sustained period of time and outputs as high at 450W for brief periods of time are possible (Bicycling Science). Considering that the XO can only accept a maximum of 17W at one time when charging, directing the entire output of the bicycle generator to the laptop, will still mean pedaling for about 2 hrs (the average time to fully charge the XO battery at 17W) to charge the laptop. Since consistent power outputs of 50-100W will likely be possible for a bicycle generator, the generator can either connect to multiple XO to charge several at once, or store excess power in a battery, where it can later be discharged to fully charge an XO. By using a battery, pedaling on the bicycle for as little as 30 minutes should be sufficient to fully charge an XO thus allowing human power to a be a very attractive power option for the XO. |
|||
===Bicycle Generator Basics=== |
|||
Looking at a bicycle generator from a system level we have the following: |
|||
A human powered bicycle provides rotational motion that is then connected to a generator through some sort of transmission (through a chain, belt, gearing or frictional contact) to produce electrical energy. The power output of the generator is dependent on the type of generator used as well as the RPMs of the generator, where a higher RPM will produce a higher current and thus more power. DC motors can produce power at low RPMs, but the power output is unregulated and the motor can be less efficient than an alternator when at high RPMs. An alternator has voltage regulation to maintain a voltage output of between 13.5V and 14.5V but typically requires higher RPMs to produce power, sometimes as high as 8,000 to 11,000 RPMs, though some low speed alternators can generate power with as little as 600 RPMs. As the generator requires a higher rotational rate than what’s considered comfortable pedaling speed for humans (70-80 RPMs), some sort of gearing will be required to effectively power the generator. This can be done by utilizing the existing gearing on a bicycle or by adding an additional gearbox. A flywheel can also be added to the crank of a bicycle to both make the bicycle easier to pedal by storing rotational energy and smooth out current spikes on the generator’s output which occurs whenever the rotational speed changes dramatically (such as during startup of the generator). |
|||
To ensure than the output current is DC and to prevent power surges from harming circuitry a diode or full bridge rectifier should be added to the generator output followed by a fuse rated for no higher than 20A. From this point, the output will go through a regulator which will either divide the output power between several XOs so that not one laptop receives more than 17W at a time, or it will divert 17W of power to a single XO and the rest to a battery. Current and voltage regulation is needed to ensure that the output power to the XO is between 11V and 25V and that the output current is less than 1.5A. For power going to the battery, a charge controller is needed to ensure that the battery doesn’t overcharge and that the current and voltage is acceptable for the battery being used. When the generator stops running, the battery can then discharge to the XO until it’s fully charged. However, charging the battery and then later discharging it retains only about 80% of the power, so there are some efficiency losses through this method (Appropriate Technology; Tools, Choices, and Implications (Hazeltine 1999)). A lead acid battery is an inexpensive and attractive option, though these batteries should never be deep cycled and the charge going into the battery should be monitored carefully. |
|||
==ILXO Proposed Bicycle Generator== |
|||
This summer, the ILXO team brainstormed several generator concepts and constructed one setup to test the feasibility of a bicycle generator. The following plans are what we believe to be the best way to construct a bicycle generator inexpensively than can accommodate a range of different bicycle as well as DC motor and alternator sizes. To accomplish this, we decided on the following characteristics for the bicycle generator: |
|||
====Generator Characteristics==== |
|||
=====Bicycle Connection===== |
|||
A key accomplishment of our design is the ability to quickly connect bicycles of various sizes to the generator quickly without having to cannibalize these bicycles. To do this, the generator is driven directly using the rear wheel of the bicycle through frictional contact without the use of a belt or additional transmission. Though this method is less efficient than other connections, this allows bicycles to easily be switched in and out of the generator without much work. The bike stand is modeled after a common bicycle trainer where a welded frame of pipe provides the structural support for the rear wheel. The frame is held in place by a simple clamp that secures to the hub and elevates the rear wheel so that it can spin freely. The rear wheel comes in direct contact with the driving wheel of the alternator or DC motor to transfer power. |
|||
One advantage of this |
|||
For this setup to effectively work the generator wheel must be in close contact with the rear wheel of the bicycle or power will be lost due to poor contact. It’s best to |
|||
Adjustable Generator Setup |
|||
Bicycle wheels vary in size anywhere from 408mm to 740mm in diameter so |
|||
No Current Smoothening |
|||
Though use of a flywheel is nice for current smoothening, this adds extra expense and complexity to the device and serves as a potential hazard for children and thus will not be included |
|||
Difficulty Finding Alternator/DC motor specifications |
|||
Considering that there are a range of different alternators and permanent magnet DC motors, that there lacks a current sizing standard for how these motors are constructed and how we have no way of determining which motors would be most available in regions where bicycle generators might be used, having a system that can easily incorporate motors of various sizes is imperative for building the generator |
|||
Design: |