View source for Swapping XO Man Colors

{{TOCright}}
First, find someone to swap XO man colors with! You will need a standard #1 Phillips head screwdriver and something to hold screws in. (In a pinch, parts taken off the XO can serve as temporary containers) This replacement can be done within 15 minutes, even with little experience. You'll be removing the display; please do be careful of static, which can destroy parts of your XO. Do see the disassembly advice! [[http://wiki.laptop.org/go/Disassembly_draft]]
<br>
<br>

[[image:screen_0.jpg|thumb|left|Before we begin]]
<br style="clear:both" />

== Taking off the front panel ==

=== Step 1 ===

Open the laptop and flip the screen up. Rotate it a quarter turn as shown in the sequence below.
Next, remove the screws from the bottom of the screen - there are two on each side (right/left) of the XO, so make sure to get all four.

[[image:Screen_1a.jpg|thumb|left|Flip screen up]] 
[[image:Screen_1b.jpg|thumb|left|Rotate]] 
<br style="clear:both" />
[[image:Screen_1c.jpg|thumb|left|Unscrew - remember, there are 4.]]
<br style="clear:both" />

=== Step 2 ===

Remove the two green panels from the side of the XO. Slide them upwards and lift them off as shown.

[[image:Screen_2a.jpg|thumb|left]] 
[[image:Screen_2b.jpg|thumb|left|Slide up]] 
<br style="clear:both" />
[[image:Screen_2c.jpg|thumb|left|Lift off]]
<br style="clear:both" />

=== Step 3 ===

Finally, pull off the front panel. It is tabbed, so it can simply be pulled out. Pull the bottom out (where the screws came out), and gently slide the piece downwards and out.

[[image:Screen_3a.jpg|thumb|left]] 
[[image:Screen_3b.jpg|thumb|left]] 
<br style="clear:both" />

== Taking out the screen ==

=== Step 1 ===

To get the screen out, remove the four screws highlighted.

[[image:Screen_4a.jpg|thumb|left|Unscrew]] 
<br style="clear:both" />

=== Step 2 ===

Next, carefully slide the screen out, pulling the bottom out. '''Do not''' tug it or let go, as it will still be connected to the motherboard by two cables.

 [[image:Screen_4b.jpg|thumb|left|Slide out gently]] 
[[image:Screen_4c.jpg|thumb|left]]
<br style="clear:both" />
[[image:Screen_4d.jpg|thumb|left| Watch out for cables!]] 
[[image:Screen_4e.jpg|thumb|left| Unhook the cable]] 
<br style="clear:both" />
[[image:Screen_4f.jpg|thumb|left| Watch out for this little cable, too.]] 
[[image:Screen_4g.jpg|thumb|left| Good to go!]]
<br style="clear:both" />




== Swapping the XO Man ==
=== Step 1 ===
[[image:antenna1a.JPG|thumb|left|Take out 4 screws]] 
[[image:antenna1b.JPG|thumb|left|Turn over. Pull up and remove the back plate]]
<br style="clear:both" />

=== Step 2 ===
[[image:Xoman1.JPG|thumb|left|Turn the back plate over. Note where the colored plastic fits in.]] 
[[image:Xoman2.JPG|thumb|left|Use a screwdriver to pop these out]] 
<br style="clear:both" />
[[image:Xoman3.JPG|thumb|left|Turn plate over so the XO man faces you. Pull the plastic part out.]] 
[[image:Xoman4.JPG|thumb|left|Note how the tabs fit in with the back plate.]] 
<br style="clear:both" />
[[image:Xoman5.JPG|thumb|left|Fit the new piece in the back plate and snap it back in place.]]
<br style="clear:both" />

=== Step 3 ===
[[image:Antenna3e.JPG|thumb|left|Turn over. Replace the back plate.]] 
[[image:Antenna3fi.JPG|thumb|left|Pick the right screw! (Try magnetizing your screwdriver.)]] 
<br style="clear:both" />
[[image:Antenna3fii.JPG|thumb|left|Turn over. Secure the back plate by putting in the four screws where indicated.]]
<br style="clear:both" />

== Replacing the screen ==

=== Step 1 ===

Replace the screen by sliding the connection cables into place and clipping them back down (it is generally easier to clip the thinner one that has a longer tether first). Reseat the screen, making sure that it sits flat and that none of the spacers are gone.

[[image:Screen_5a.jpg|thumb|left| Clip little cable in]] 
[[image:Screen_5b.jpg|thumb|left| Clip big cable in]]
<br style="clear:both" />
[[image:Screen_5c.jpg|thumb|left| Gently slide screen back in]] 
[[image:Screen_5d.jpg|thumb|left| The screws with the large heads (4) go back in]]
<br style="clear:both" />

=== Step 2 ===

Slide the front panel back on, making sure that it sits flat. Note that there are hooks on the side of the panel (highlighted in blue) that need to slide into place; pushing the top of the screen flat and sliding it upwards works well.

[[image:Screen_6a.jpg|thumb|left| Watch out for these hooks]] 
[[image:Screen_6b.jpg|thumb|left| The rest of the panel slides into place]]
<br style="clear:both" />

=== Step 3 ===

Slide the green side pieces back into place. Then, rotate the XO a quarter turn and put the remaining screws back. Don't forget that the screws go in on both sides (right/left).

[[image:Screen_7a.jpg|thumb|left]] 
[[image:Screen_7b.jpg|thumb|left| Side panels slide back in place]] 
<br style="clear:both" />
[[image:Screen_7c.jpg|thumb|left| Almost there!]]
[[image:Screen_7d.jpg|thumb|left| Rotate]] 
<br style="clear:both" />
[[image:Screen_7e.jpg|thumb|left| Put screws (4) back in. ]]
<br style="clear:both" />

And you're done! Yay! :D

[[Category:Repair]]