Screen replacement/lang-es: Difference between revisions

From OLPC
Jump to navigation Jump to search
No edit summary
No edit summary
Line 14: Line 14:
<br style="clear:both" />
<br style="clear:both" />


== Taking off the front panel ==
== Quitar el panel frontal ==


=== Step 1 ===
=== 1 ===


Abrir la laptop y rotar la pantalla como se viste en las imagenes. Remover los tornillos que se encuentra en el fondo de la pantalla - hay dos a la derecha y dos a la izquierda.
Open the laptop and flip the screen up. Rotate it a 90 degree angle as shown in the sequence below.
Next, remove the screws from the bottom of the screen - there are two on each side (right/left) of the XO, so make sure to get all four.


[[image:Screen_1a.jpg|thumb|left|Flip screen up]] [[image:Screen_1b.jpg|thumb|left|Rotate]] [[image:Screen_1c.jpg|thumb|left|Unscrew - remember, there are 4.]]
[[image:Screen_1a.jpg|thumb|left|Abrir la laptop]] [[image:Screen_1b.jpg|thumb|left|Rotar]] [[image:Screen_1c.jpg|thumb|left|Destornillar - recordiendo que hay 4.]]
<br style="clear:both" />
<br style="clear:both" />


=== Step 2 ===
=== 2 ===


Remover los dos paneles verdes laterales. Deslizar los paneles hacia arriba y remover los.
Remove the two green panels from the side of the XO. Slide them upwards and lift them off as shown.


[[image:Screen_2a.jpg|thumb|left]] [[image:Screen_2b.jpg|thumb|left|Slide up]] [[image:Screen_2c.jpg|thumb|left|Lift off]]
[[image:Screen_2a.jpg|thumb|left]] [[image:Screen_2b.jpg|thumb|left|Deslizar hacia arriba]] [[image:Screen_2c.jpg|thumb|left|Remover]]
<br style="clear:both" />
<br style="clear:both" />


=== Step 3 ===
=== 3 ===


Por fin, remover el panel frontal. Cuidado con las ranuras. Jalar primero al fondo del panel (donde los tornillos estaban) hacia abajo y remover el panel.
Finally, pull off the front panel. It is tabbed, so it can simply be pulled out. Pull the bottom out (where the screws came out), and gently slide the piece downwards and out.


[[image:Screen_3a.jpg|thumb|left]] [[image:Screen_3b.jpg|thumb|left]]
[[image:Screen_3a.jpg|thumb|left]] [[image:Screen_3b.jpg|thumb|left]]

Revision as of 20:04, 27 May 2008

  Traducción de Screen_replacement original  
  english | español   +/- cambios  

Reponer la pantalla es bastante fácil. Para hacer esto, necesitara un destornillador #1 y un recipiente para los tornillos. Se puede hacer en unos 10 minutos, aún si no tiene mucha experiencia.

Before we begin


Quitar el panel frontal

1

Abrir la laptop y rotar la pantalla como se viste en las imagenes. Remover los tornillos que se encuentra en el fondo de la pantalla - hay dos a la derecha y dos a la izquierda.

Abrir la laptop
Rotar
Destornillar - recordiendo que hay 4.


2

Remover los dos paneles verdes laterales. Deslizar los paneles hacia arriba y remover los.

Screen 2a.jpg
Deslizar hacia arriba
Remover


3

Por fin, remover el panel frontal. Cuidado con las ranuras. Jalar primero al fondo del panel (donde los tornillos estaban) hacia abajo y remover el panel.

Screen 3a.jpg
Screen 3b.jpg


Taking out the screen

Step 1

To get the screen out, remove the four screws highlighted.

Unscrew


Step 2

Next, carefully slide the screen out, pulling the bottom out. Do not tug it or let go, as it will still be connected to the motherboard by two cables.

Slide out gently
Screen 4c.jpg
Watch out for cables!


Unhook the cable
Watch out for this little cable, too.
Good to go!



Replacing the screen

Step 1

Replace the screen by sliding the connection cables into place and clipping them back down (it is generally easier to clip the thinner one that has a longer tether first). Reseat the screen, making sure that it sits flat and that none of the spacers are gone.

Error creating thumbnail: File missing
Clip little cable in
Clip big cable in


Gently slide screen back in
The screws with the large heads (4) go back in


Step 2

Slide the front panel back on, making sure that it sits flat. Note that there are hooks on the side of the panel (highlighted in blue) that need to slide into place; pushing the top of the screen flat and sliding it upwards works well.

Watch out for these hooks
The rest of the panel slides into place


Step 3

Slide the green side pieces back into place. Then, rotate the XO 90 degrees and put the remaining screws back. Don't forget that the screws go in on both sides (right/left).

Screen 7a.jpg
Side panels slide back in place
Almost there!


Rotate
Put screws (4) back in.


And you're done! Yay! :D