Keyboard field repairs: Difference between revisions

From OLPC
Jump to navigation Jump to search
No edit summary
(Added first 4 photos)
Line 5: Line 5:
== Materials ==
== Materials ==


[[image:A1-Supplies.jpg|thumb|left|Supplies: silicone sealant, toothpicks, cotton swabs, water, table protector.]]
[[image:A1-Supplies.jpg|thumb|center]]
<br style="clear:both" />
<br style="clear:both" />


Line 29: Line 29:
Using one toothpick to hold the key in place, gently apply a small amount of silicone to the torn sides of the key with a second toothpick.
Using one toothpick to hold the key in place, gently apply a small amount of silicone to the torn sides of the key with a second toothpick.


[[image:A2-Apply Silicone.jpg|thumb|center]]
(Photo A2)
<br style="clear:both" />


Use a damp (not soaking wet) cotton swab to remove the excess silicone sealer.
Use a damp (not soaking wet) cotton swab to remove the excess silicone sealer.


[[Image:A3-Remove Excess.jpg|thumb|center]]
Photo A3)
<br style=clear:both/>


More cleanup may be needed.
More cleanup may be needed.


[[Image:A4-Needs More Cleanup.jpg|thumb|center]]
(Photo A4)
<br style=clear:both/>


Use a damp tissue for a final touchup. In this photo, the F, G, and H keys and the right half of the space bar were repaired previously and have already dried.
Use a damp tissue for a final touchup. In this photo, the F, G, and H keys and the right half of the space bar were repaired previously and have already dried.

Revision as of 04:51, 29 August 2008

While OLPC recommends replacing ripped keyboards, that may not always be possible or, may be too costly if several laptops are involved. This simple fix uses a relatively non-toxic silicone sealer that has no harmful fumes. The repair could be, and has been, done safely by children.

Materials

A1-Supplies.jpg



  • Clear Silicone tub and tile sealant (goes on white, dries clear). A 6 oz tube costs less than $3 at most hardware stores and is enough to do dozens of laptops.
  • Toothpicks for applying the sealer
  • Cotton swabs, tissues and water for cleanup
  • Something to protect your table top if doing the repair with the keyboard removed from the laptop (aluminum foil is shown here).

If only a few keys are involved, you may wish to do the repair with the keyboard in place. Follow the second set of directions below to do the repair without removing the keyboard.

If the damage is more extensive, you will probably want to remove the keyboard following these directions:

(Add link to dis-assembly instructions)

Repair With Keyboard Removal

After removing the keyboard, gently lift off the green silicone keypad, being careful to not tear additional keys. Lay it on your table protector.

Using one toothpick to hold the key in place, gently apply a small amount of silicone to the torn sides of the key with a second toothpick.

A2-Apply Silicone.jpg


Use a damp (not soaking wet) cotton swab to remove the excess silicone sealer.

A3-Remove Excess.jpg


More cleanup may be needed.

A4-Needs More Cleanup.jpg


Use a damp tissue for a final touchup. In this photo, the F, G, and H keys and the right half of the space bar were repaired previously and have already dried.

(Photo A5)

Allow the silicone to dry overnight before re-assembling the laptop according to the directions on the wiki.

Repair Without Keyboard Removal

While this may seem easier than removing the keyboard, you must work very carefully to not allow silicone to get under the green silicone keypad.

A key that had been completely torn off was re-fitted in this repair.

(Photo B1)

Carefully fit the key back into its place in the keyboard.

(Photo B2)

Apply silicone to one edge of the key and carefully clean it. If you try to do the entire key at once, it will be difficult to keep it in place while working.

(Photo B3)

Allow the first side to dry overnight. (Photo B4)

Holding the key in place with one toothpick, carefully apply silicone to the remaining three sides, being careful not to get it under the key.

(Photo B5).

Clean up with a toothpick. To avoid having sealer run under the key, it is probably best not to use the wet cotton swab or wet tissue here.

(Photo B6)

Let they keyboard dry overnight. Note the repair isn't as clean as the one with the keyboard removed, but that is because we did not use the water in the cleanup.

(Photo B7)

Test the results. This one worked.

(Photo B8)

If the key does not work, you may wish to remove the keyboard according to the disassembly instructions, clean off the excess sealer, and follow the instructions above.