User talk:Wad: Difference between revisions

From OLPC
Jump to navigation Jump to search
m (Reverted edits by Fat prick (Talk) to last version by Wvbailey)
(Pen support?)
Line 32: Line 32:


My personal rule is this: do not post anything that can mislead and result in damage to the laptop or harm to the student. Bill [[User:Wvbailey|Wvbailey]] 17:09, 30 December 2008 (UTC)
My personal rule is this: do not post anything that can mislead and result in damage to the laptop or harm to the student. Bill [[User:Wvbailey|Wvbailey]] 17:09, 30 December 2008 (UTC)

== Pen support? ==
On [[XO-2]]: "Tablet mode - when flat, the handbook provides a surface for drawing, writing, and games."

Does that mean pen support?

And what about [[XO-3]]? Pen support, too? --[[User:Jhartmann|Jhartmann]] 20:38, 30 June 2010 (UTC)

Revision as of 20:38, 30 June 2010

Active Antenna parts

The ActiveAntenna board picture is too small/blurry to read the chip part numbers. Could you fix it or, alternately, just read off the part numbers? I think I know the big one already, the 88W8388. There are two interesting ones below that.

What is under the can? (maybe you can pop it right off; that works with some Marvell devices)

What is on the back?

I'm especially looking for part numbers for EEPROM and FLASH devices.

24.110.145.202 15:19, 26 December 2007 (EST)

OLPC grandma review

She reviews the wifi connectivity process. --Sj talk 16:16, 1 February 2008 (EST)

Dissasembly of keyboard

I see that you've edited the disassembly of the keyboard section to include the statement that it would not work. This is in direct conflict to the evidence which is that taking the keyboard apart does indeed resolve the sticky keyboard - whether it's due to removal of contamination or "fluffing" of the contact spacers, I have talked to 3 users that have mostly solved their keyboard problems with this procedure.

As long as one is out of warranty, what other recourse does the XO user have. Until you get replacement keyboards out, folks will try this process and many will be helped. Alc 16:21, 20 April 2008 (EDT)

reply at User_talk:Alc

Safety first

Your supposition about frequency response is not correct. There are almost no capacitors at the front end to act with the 100k's as a low-pass filter. Moreover, the laptop's resistor value is quite low, about 1K as I recall.

If you make the grievous mistake of sticking the unprotected port inputs into 120VAC or 240VAC the "chassis/frame" including the port's metal shell will be come live.

The laptop's small-value input resistor does does not protect the input diode/tranzorb at the front end. So if you reverse a 1.5 volt battery polarity (i.e. minus into the port) you'll blow the diode. I've tested this with decent current limiting power supplies.

The 100K's are a very low-cost stop-gap and do not represent particularly good design. To avoid safety issues and potential damage to the laptop you should build the differential amplifier (it costs less than $10). This will protect you from frying yourself and/or the laptop up to 240VAC. There are some design simplifications and cost reductions possible that I came up with.

My personal rule is this: do not post anything that can mislead and result in damage to the laptop or harm to the student. Bill Wvbailey 17:09, 30 December 2008 (UTC)

Pen support?

On XO-2: "Tablet mode - when flat, the handbook provides a surface for drawing, writing, and games."

Does that mean pen support?

And what about XO-3? Pen support, too? --Jhartmann 20:38, 30 June 2010 (UTC)