OLPC Firmware q4b09: Difference between revisions

From OLPC
Jump to navigation Jump to search
No edit summary
No edit summary
Line 23: Line 23:
|-
|-
| CForth version <!-- cd cforth ; git log -n 1 -->
| CForth version <!-- cd cforth ; git log -n 1 -->
| [http://dev.laptop.org/git/users/wmb/cforth/commit/?id=b3d243415a2c82c9f5a9b94de0c45a13f3eb2636]
| [http://dev.laptop.org/git/users/wmb/cforth/commit/?id=b3d243415a2c82c9f5a9b94de0c45a13f3eb2636 b3d24341]
|-
|-
| Wireless firmware version <!-- hmm -->
| Wireless firmware version <!-- hmm -->

Revision as of 15:46, 3 September 2011

  This page is monitored by the OLPC team.

OLPC Firmware Release q4b09

For A2 and later boards ONLY! Do not install on A1 boards.

Release for testing inclusion of the initramfs into builds

Download q4b0.rom
Build date time 2011-08-24 02:02:29
Source revision 2502
EC version 0.2.03
CForth version b3d24341
Wireless firmware version Libertas thinfirm 9.0.7.p2

Changes since q4b08

OpenFirmware

  • When reprogramming the EC FLASH, skip the page that contains the EC configuration flags.
  • OLPC keyboard selftest improvements for the case where the SP manages PS/2 and handles game buttons.
  • Fixes to initrd loading
  • Turned off most of the serial messages for early startup.
  • Implemented an upsampling filter using iwMMX instructions and used it to upsample the audio for the startup jingle.
  • DCON driver - Use GPIO edge detection hardware to avoid the need for disabling interrupts while waiting for DCON freeze.
  • Trac: #11117. Move storage LED manipulation to fw.bth for XO-1.5 and XO-1.75, use storage LED when writing to EC or OpenFirmware FLASH, show a display indicator of EC automatic reflash.
  • Initial revision of RM3150 touchscreen driver.
  • Regularized the naming of some words in the TWSI driver.
  • Use virtual addressing for the interrupt controller device driver.
  • Added some support to the RTC driver for testing wakeup from suspend.
  • Big renaming of configuration constants associated with memory layout.

CForth

  • Support game buttons in PS/2 keyboard handler (thanks to Paul Fox).

EC

  • no change

WLAN

  • no change


Which Firmware Do You Have?

The best method for finding out what firmware version you have on a laptop depends on whether the laptop is secured or not, and what operating state it is in.

Unsecured Laptop

Obtain the Ok prompt, the firmware version is displayed in the startup banner, thus:

 OLPC ..., ... memory installed, ..., S/N SHF7250024D
 OpenFirmware  q4b09 ...   EC Firmware Ver:...
               ^^^^^

You can also obtain the built date:

 ok .built

This is the date and time that this image of the firmware was built by the release engineer.

Secured Laptop

Power up the laptop with the ✓ (check mark) game button held down. You will be asked to Release the game keys to continue. Release the ✓ (check mark) game button and watch carefully. For a short time the startup banner will be displayed, like this:

 OLPC ..., ... memory installed, ..., S/N SHF7250024D
 OpenFirmware  q4b09 ...   EC Firmware Ver:...
               ^^^^^

Alternatively, if the laptop is already booted, go to the Sugar home view, click on the icon at the centre of the screen and select "My Settings" then "About my Computer." The firmware version is displayed there.

Alternatively, in the Terminal activity or a text console, type:

 cat /proc/device-tree/openprom/model

or

 cat /ofw/openprom/model

With certain older firmware versions, if the operating system will not start, and the laptop is secured, you will not be able to obtain the firmware version using the above methods, so our recommendation is to go ahead and upgrade anyway. The procedure is safe and will not do anything if you already have up-to-date firmware.


Installation

When installing new firmware, you must have a well-charged battery and the AC adapter plugged in. The firmware update code will not proceed otherwise. Possible error messages are:

error message how to fix
AC not present plug in the power cord, check the battery LED is on, then try again.
No external power plug in the power cord, check the battery LED is on, then try again,
No battery plug in the battery, check the latches, then try again, or try another battery,
Battery low allow more time for the battery to charge, then try again, or try another battery.

Unsecured Laptop

This section is for unsecured laptops. Most XO-1.5 and XO-1.75 laptops are unsecured. Most developer XO laptops are unsecured. To unsecure your laptop, follow the instructions at Activation and Developer Keys.

You may install using either:

  • a USB drive or SD card,
  • the laptop's internal drive,
  • a network.

Choose one.

Using a USB drive or SD card

  • check the battery is inserted and locked,
  • check that the power cord is in place and the battery indicator is green,
  • insert the USB drive or SD card,
  • turn on the laptop, and get to the 'ok' prompt. See Ok for more detail. You should see:
ok
  • if the downloaded file is on a USB drive, type:
 flash u:\q4b09.rom
  • if the downloaded file is on an external SD card:
 flash sd:\boot\q4b09.rom
  • wait for the laptop to reboot itself,
  • remove the USB drive or SD card.

(Expert users may remove the USB drive after the message "Got firmware" ... at this stage the file has been read and closed.)

Using the laptop internal drive

An alternate method is to download the firmware file to the laptop internal drive and then install from the internal drive.

  • start the laptop,
  • connect to a wireless or wired network,
su
cd /versions/boot/current/boot/
wget http://dev.laptop.org/pub/firmware/q4b09/q4b09.rom
  • check the battery is inserted and locked,
  • check that the power cord is in place and the battery indicator is green,
  • turn on the laptop, and get to the 'ok' prompt. See Ok for more detail. You should see:
ok
  • if the downloaded file is on an XO-1, type:
flash n:\boot\q4b09.rom
  • if the file is on the internal SD card of an XO-1.5 or XO-1.75:
flash int:\boot\q4b09.rom

Using a network

You will need a compatible USB to ethernet adapter, or an open or WEP wireless access point, connected to the internet.

  • check the battery is inserted and locked,
  • check that the power cord is in place and the battery indicator is green,
  • turn on the laptop, and get to the 'ok' prompt. See Ok for more detail. You should see:
ok
  • if using wireless, type the essid of the wireless network:
essid mynetwork
  • if using a WPA wireless access point, type the WPA key for the network:
wpa passphrase
  • type the flash command using the download link above, but change all slash characters so they are backwards, for example:
flash http:\\dev.laptop.org\pub\firmware\q4b09\q4b09.rom

Secured Laptop

Secured laptops can only use flash firmware that has been signed. All mass-production machines had the latest firmware at the time of manufacture.

Upgrading firmware describes how to upgrade to a newer signed firmware release.

See also

  • Cheat codes for information about how game buttons control startup options.