XO-1/Touchpad/Issues: Difference between revisions
< XO-1
Jump to navigation
Jump to search
m (moved Three known touchpad issues to XO-1/Touchpad/Issues: so many models these days, but this page applies only to one.) |
|||
| (8 intermediate revisions by 4 users not shown) | |||
| Line 1: | Line 1: | ||
<noinclude>[[Category:Touchpad]]</noinclude> |
|||
{{G1G1 Support FAQ}} |
{{G1G1 Support FAQ}} |
||
__NOTOC__ |
__NOTOC__ |
||
Note: This information is relevant for early production XO-1 units with ALPS touchpads, identified as "CL1" during early boot. |
|||
Occasionally, a laptop's touchpad will behave abnormally. This behavior includes the pointer jumping to a corner of the screen, or moving wildly. On current software ([[Release notes|release 8.2 or better]], [[USB upgrade|consider upgrading!]]), the touchpad will be automatically recalibrated when this happens. You should hold your fingers away from the touchpad when this happens. [[Touchpad_driver_changes|Later Touchpad driver changes]] further reduce this problem. |
Occasionally, a laptop's touchpad will behave abnormally. This behavior includes the pointer jumping to a corner of the screen, or moving wildly. On current software ([[Release notes|release 8.2 or better]], [[USB upgrade|consider upgrading!]]), the touchpad will be automatically recalibrated when this happens. You should hold your fingers away from the touchpad when this happens. [[Touchpad_driver_changes|Later Touchpad driver changes]] further reduce this problem. |
||
A recalibration of the touchpad can be manually invoked using the [[Recalibrating Touchpad|"four-finger salute"]] (Escape + Frame + Right Arrow + Fn, with Fn pressed last). Work-arounds in extreme cases include using a common USB mouse with the laptop. |
A recalibration of the touchpad can be manually invoked using the [[Recalibrating Touchpad|"four-finger salute"]] (Escape + Frame + Right Arrow + Fn, with Fn pressed last). Work-arounds in extreme cases include using a common USB mouse with the laptop. |
||
=If using older software/hardware= |
|||
While not all issues have been resolved in 2009, especially when using older software/hardware from 2007 and earlier in 2008, three touchpad issues stood out: |
|||
== The pointer jumps to the bottom-right corner of the screen == |
|||
This can happen right after you touch the touchpad. Rebooting often helps (see <trac>2804</trac>). |
|||
The [[Recalibrating Touchpad|four-finger salute]] (Escape + Frame + Right Arrow + My Ass) usually fixes this. |
|||
AHAHAHAHAHA< |
|||
== '''IF YOU READ THIS YOU ARE GAY''' == |
|||
==The pointer moves around by itself== |
|||
Instead of reliably following your finger, the pointer can move around on its own, sometimes when a hand is close to it. The [[Recalibrating Touchpad|four-finger salute]] (Escape + Frame + Right Arrow + Fn, with Fn pressed last) usually fixes this. Automatic recalibration on reboot may also fix the problem. |
|||
== Mouse moves mostly vertically == |
|||
If the touchpad works fine vertically but doesn't function horizontally (<trac>5575</trac>), it is likely due to damaged touchpad wiring. This was corrected and is very rarely seen in recently produced laptops. |
|||
= Intermittent failure after replacement = |
|||
The touchpad in my G1G1 XO was recently (Feb 2010) replaced. Worked for a while, but now is intermittently stuck to moving vertically - can be forced to move to the left of right margin of the frame by agressively moving finger on touchpad. |
|||
It could be related to the wifi I recently protected. |
|||
=Log= |
|||
4/08/2010 - not working |
|||
4/08/2010 - not working after reboot |
|||
4/09/2010 - working perfectly |
|||
4/20/2010 - 4/23/2010 not working |
|||
4/23/2010 - working after shaking machine |
|||
4/23/2010 - not working after moving XO to its usual location |
|||
5/03/2010 - working, machine was rebooted today and touchpad works. |
|||
=Reducing the impact= |
|||
In addition to forcing a recalibration yourself, using the [[Recalibrating Touchpad|four-finger salute]], the kernel will sometimes notice a recalibration is necessary, and commence the process automatically. In releases 8.2 and later it's possible to adjust some parameters which affect how, and how quickly, the kernel will tell the touchpad to recalibrate. This script will sets the most pertinent of the mouse driver parameters to values that make the calibration take less time -- meaning your fingers don't have to be off the pad as long before you can start using it again. Unfortunately, this needs to be run as root (sudo), so you can't just put it into a .xsession or .bashrc file. |
|||
'''Note: this is only recommended if you're running a stock version of release 802 or earlier, or early releases of F11 on the XO-1.''' More recent driver work has rendered what this script does mostly unnecessary. |
|||
<pre> |
|||
#!/bin/sh |
|||
# the available touchpad parameters (the ones pertinent to recalibration) |
|||
# are as follows: |
|||
# |
|||
# recalib_delta: packets containing a delta this large will |
|||
# cause a recalibration. (int) |
|||
# jumpy_delay: delay (ms) before recal after jumpiness detected (int) |
|||
# spew_delay: delay (ms) before recal after packet spew detected (int) |
|||
# recal_guard_time: interval (ms) during which recal will be |
|||
# restarted if packet received (int) |
|||
# post_interrupt_delay: delay (ms) before recal after recal |
|||
# interrupt detected (int) |
|||
# autorecal: enable recalibration in the driver? (int) |
|||
# |
|||
p=/sys/module/psmouse/parameters |
|||
if [ $(whoami) != root ] |
|||
then |
|||
echo must be root >&2 |
|||
exit 1 |
|||
fi |
|||
( echo Before: ; grep ^ $p/* ) >/tmp/cur_psmouse_params |
|||
if [ "$1" = show ] |
|||
then |
|||
cat /tmp/cur_psmouse_params |
|||
exit |
|||
fi |
|||
echo Setting mouse parameters: |
|||
# all values in milliseconds |
|||
echo 200 >$p/jumpy_delay |
|||
echo 200 >$p/spew_delay |
|||
echo 400 >$p/recal_guard_time |
|||
echo 100 >$p/post_interrupt_delay |
|||
( echo After: ; grep ^ $p/* ) | diff /tmp/cur_psmouse_params - |
|||
exit |
|||
</pre> |
|||
= Large Jump Logging Technique = |
|||
The following highly technical sequence is for developers with build 802 on XO-1 C2 units, which lets them capture touchpad events in more detail ... it can be deployed to children with the instruction "when the touchpad goes nuts, please press the key to the left of the frame key, this will record data that we will use to analyse the problem, and you'll hear a short beep when it is done.". |
|||
The key to the left of the frame key on the [[Keyboard]] is the '''Bulletin Board''' key, which has two rectangles overlaid, sometimes in a circle ([[Image:Key_bboard.jpg]]) and was intended to toggle display of the shared visual clipboard; a feature that is not yet shipped. |
|||
To configure a laptop for this data gathering, the following commands must be run as root on the laptop: |
|||
<pre> |
|||
# make a script that records the kernel messages to a file. |
|||
cat << EOF > /usr/local/bin/grab-touchpad-log |
|||
#!/bin/sh |
|||
dmesg | gzip - > /home/olpc/dmesg.\`date +%s\`.gz |
|||
speaker-test --test=sine --frequency=800 & |
|||
PID=\$! |
|||
sleep 0.1 |
|||
kill \$PID |
|||
EOF |
|||
# make the script executable. |
|||
chmod +x /usr/local/bin/grab-touchpad-log |
|||
# configure kernel to record touchpad events on next boot and now. |
|||
echo 'echo 1 > /sys/module/psmouse/parameters/tpdebug' >> /etc/rc.local |
|||
echo 1 > /sys/module/psmouse/parameters/tpdebug |
|||
# set up the matchbox window manager to run the script when the key |
|||
# to the left of the frame key is hit. |
|||
echo 'XF86Messenger=!/usr/local/bin/grab-touchpad-log' \ |
|||
>> /usr/share/sugar/data/kbdconfig |
|||
</pre> |
|||
[[Category:Touchpad]] |
|||
Latest revision as of 04:50, 3 February 2012
This page is part of the XO Support FAQ. Support Index | Print This Page
<imagemap>
Image:Support-banner-square.png|173px|community support pages rect 0 0 135 204 [1] rect 135 0 345 204 Support FAQ rect 0 205 135 408 [2]
- Comment : there's some whitespace here:
rect 135 205 345 408 Other support
- maybe desc none is better. testing.
desc none
</imagemap>
Note: This information is relevant for early production XO-1 units with ALPS touchpads, identified as "CL1" during early boot.
Occasionally, a laptop's touchpad will behave abnormally. This behavior includes the pointer jumping to a corner of the screen, or moving wildly. On current software (release 8.2 or better, consider upgrading!), the touchpad will be automatically recalibrated when this happens. You should hold your fingers away from the touchpad when this happens. Later Touchpad driver changes further reduce this problem.
A recalibration of the touchpad can be manually invoked using the "four-finger salute" (Escape + Frame + Right Arrow + Fn, with Fn pressed last). Work-arounds in extreme cases include using a common USB mouse with the laptop.