OLPC Firmware q4d10

  This page is monitored by the OLPC team.

OLPC Firmware Release q4d10

Works on XO-1.75 B1 and C1 only. Do not use on A2 or A3.

• restore thermal protection after suspend resume test, <trac>11779</trac>,
• fix a disk label error when file specifications are abbreviated, e.g. fs-update u:fs.zd,
• fix "EDI byte in confused" messages seen during tag operations.

Download	q4d10.rom
Build date time	2012-04-18 21:43:50
Source revision	2945
EC version	0.4.02
CForth version	89c52d57
Wireless firmware version	Libertas thinfirm 9.0.7.p2

Changes

Open Firmware

• 2944 OLPC XO-1.75 - restore thermal protection after suspend, #11779
• 2943 disklabel - file spec parsing, avoid treating a-h as partition letter if UFS partition support is disabled.
• 2942 OLPC XO-1.75 and XO-3 - changed EDI (SPI interface to EC) timing to account for rise time issue on MISO.

CForth

• none

EC

• none

WLAN

• none

Which Firmware Do You Have?

The best method for finding out what firmware version you have on a laptop depends on whether the laptop is secured or not, and what operating state it is in.

Unsecured Laptop

Obtain the Ok prompt, the firmware version is displayed in the startup banner, thus:

 OLPC ..., ... memory installed, ..., S/N SHF7250024D
 OpenFirmware  q4d10 ...   EC Firmware Ver:...
               ^^^^^

You can also obtain the built date:

 ok .built

This is the date and time that this image of the firmware was built by the release engineer.

Secured Laptop

Power up the laptop with the ✓ (check mark) game button held down. You will be asked to Release the game keys to continue. Release the ✓ (check mark) game button and watch carefully. For a short time the startup banner will be displayed, like this:

 OLPC ..., ... memory installed, ..., S/N SHF7250024D
 OpenFirmware  q4d10 ...   EC Firmware Ver:...
               ^^^^^

Alternatively, if the laptop is already booted, go to the Sugar home view, click on the icon at the centre of the screen and select "My Settings" then "About my Computer." The firmware version is displayed there.

Alternatively, in the Terminal activity or a text console, type:

 cat /proc/device-tree/openprom/model

or

 cat /ofw/openprom/model

With certain older firmware versions, if the operating system will not start, and the laptop is secured, you will not be able to obtain the firmware version using the above methods, so our recommendation is to go ahead and upgrade anyway. The procedure is safe and will not do anything if you already have up-to-date firmware.

Installation

When installing new firmware, you must have a well-charged battery and the AC adapter plugged in. The firmware update code will not proceed otherwise. Possible error messages are:

error message	how to fix
AC not present	plug in the power cord, check the battery LED is on, then try again.
No external power	plug in the power cord, check the battery LED is on, then try again,
No battery	plug in the battery, check the latches, then try again, or try another battery,
Battery low	allow more time for the battery to charge, then try again, or try another battery.

Unsecured Laptop

This section is for unsecured laptops. Most XO-1.5 and XO-1.75 laptops are unsecured. Most developer XO laptops are unsecured. To unsecure your laptop, follow the instructions at Activation and Developer Keys.

You may install using either:

• a USB drive or SD card,
• the laptop's internal drive,
• a network.

Choose one.

Using a USB drive or SD card

• download the firmware from http://dev.laptop.org/pub/firmware/q4d10/q4d10.rom and save it to a USB drive or SD card,

• shutdown the laptop,

• check the battery is inserted and locked,

• check that the power cord is in place and the battery indicator is green,

• insert the USB drive or SD card,

• turn on the laptop, and get to the 'ok' prompt. See Ok for more detail. You should see:

ok

• if the downloaded file is on a USB drive, type:

 flash u:\q4d10.rom

• if the downloaded file is on an external SD card:

 flash sd:\boot\q4d10.rom

• wait for the laptop to reboot itself,

• remove the USB drive or SD card.

(Expert users may remove the USB drive after the message "Got firmware" ... at this stage the file has been read and closed.)

Using the laptop internal drive

An alternate method is to download the firmware file to the laptop internal drive and then install from the internal drive.

• start the laptop,

• connect to a wireless or wired network,

• start the Terminal Activity and type:

su
cd /versions/boot/current/boot/
wget http://dev.laptop.org/pub/firmware/q4d10/q4d10.rom

• shutdown the laptop,

• check the battery is inserted and locked,

• check that the power cord is in place and the battery indicator is green,

• turn on the laptop, and get to the 'ok' prompt. See Ok for more detail. You should see:

ok

• if the downloaded file is on an XO-1, type:

flash n:\boot\q4d10.rom

• if the file is on the internal SD card of an XO-1.5 or XO-1.75:

flash int:\boot\q4d10.rom

Using a network

You will need a compatible USB to ethernet adapter, or an open or WEP wireless access point, connected to the internet.

• shutdown the laptop,

• check the battery is inserted and locked,

• check that the power cord is in place and the battery indicator is green,

• turn on the laptop, and get to the 'ok' prompt. See Ok for more detail. You should see:

ok

• if using wireless, type the essid of the wireless network:

essid mynetwork

• if using a WPA wireless access point, type the WPA key for the network:

wpa passphrase

• type the flash command using the download link above, but change all slash characters so they are backwards, for example:

flash http:\\dev.laptop.org\pub\firmware\q4d10\q4d10.rom

Secured Laptop

Secured laptops can only use flash firmware that has been signed. All mass-production machines had the latest firmware at the time of manufacture.

Upgrading firmware describes how to upgrade to a newer signed firmware release.

See also

• Cheat codes for information about how game buttons control startup options.