XO 1.5 USB Keyboard: Difference between revisions
No edit summary |
|||
(52 intermediate revisions by 6 users not shown) | |||
Line 1: | Line 1: | ||
<span style="color:red">'''NOTICE : '''</span> These instructions describe how to build a prototype of a non-membrane [[XO-1.5|XO-1.5 laptop]], which were used as "proof of concept" before an official production variant was designed. A non-membrane keyboard is now available as an option for [[XO-1.5]], [[XO-1.75]] and [[XO-4]] production and spares. |
|||
This page describes how to change the keyboard in a [[Hardware#XO_1.5_Laptop|XO-1.5 Laptop]] to a non-membrane USB version. |
|||
=Scope= |
|||
These are detailed instructions for installing a non-membrane keyboard into an [[Hardware#XO_1.5_Laptop|XO-1.5 laptop]]. They apply to all pre-production as well as production models. With little change, they also apply to the [[XO_CL1A|later model]] of the [[Hardware#XO_Laptop|XO-1]] (with a single capacitive touchpad). |
These are detailed instructions for installing a non-membrane keyboard into an [[Hardware#XO_1.5_Laptop|XO-1.5 laptop]]. They apply to all pre-production as well as production models. With little change, they also apply to the [[XO_CL1A|later model]] of the [[Hardware#XO_Laptop|XO-1]] (with a single capacitive touchpad). |
||
[[Image:XO1.5_USBKB_Photo60.jpg|thumb|Installed keyboard]] |
|||
Credit is freely given to the author of the instructions for doing this modification to an XO-1 ([http://www.instructables.com/id/Installing-a-USB-Keyboard-into-an-OLPC-XO-Laptop-/ part I], [http://www.instructables.com/id/Finishing-the-Job-Installing-a-USB-Keyboard-into-/ II]), found on [http://www.instructables.com instructables.com]. |
Credit is freely given to the author of the instructions for doing this modification to an XO-1 ([http://www.instructables.com/id/Installing-a-USB-Keyboard-into-an-OLPC-XO-Laptop-/ part I], [http://www.instructables.com/id/Finishing-the-Job-Installing-a-USB-Keyboard-into-/ II]), found on [http://www.instructables.com instructables.com]. |
||
A non-membrane keyboard is now available as an option for [[XO-1.5]], [[XO-1.75]] and [[XO-4]] production and spares. |
|||
===WARNING=== |
|||
The production versions use the same PS2 keyboard controller for the non-membrane keyboard as the membrane keyboard, and are much more robust and low power than the USB-based prototypes described here. |
|||
==<span style="color:red">WARNING</span>== |
|||
This modification includes permanent modifications of the XO laptop, and cannot be reversed. Even if you are experienced, '''there is a significant chance of damaging the laptop beyond repair while following these instructions'''. |
This modification includes permanent modifications of the XO laptop, and cannot be reversed. Even if you are experienced, '''there is a significant chance of damaging the laptop beyond repair while following these instructions'''. |
||
=Material= |
|||
You will need: |
You will need: |
||
* An XO-1 (CL1A) or XO-1.5 (CL1B) laptop |
* An XO-1 (CL1A) or XO-1.5 (CL1B) laptop |
||
* A micro USB keyboard (such as [http://www.cyberguys.com/ |
* A micro USB keyboard (such as [http://www.cyberguys.com/product-details/?productid=6083 this one]). [[Image:XO1.5_USBKB_Photo0.jpg|thumb|micro USB Keyboard]] |
||
* A #1 screwdriver |
* A #1 screwdriver |
||
* Fine pitch soldering equipment |
* Fine pitch soldering equipment |
||
Line 26: | Line 30: | ||
* quick drying epoxy glue or archival double-sided tape |
* quick drying epoxy glue or archival double-sided tape |
||
=Instructions= |
|||
==Preparing the Keyboard== |
|||
{| |
|||
|Test the new USB keyboard by plugging it into the XO and typing on it. |
|||
|[[Image:XO1.5_USBKB_Photo1.jpg|thumb|Screw locations in USB keyboard]] |
|||
|- |
|||
|[[Image:XO1.5_USBKB_Photo2.jpg|thumb|left|USB keyboard and its KBC]] |
|||
|Open up the USB keyboard. |
|||
|- |
|||
|Separate the keyboard controller (KBC) from the keyboard by gently pulling on the FPC. |
|||
|[[Image:XO1.5_USBKB_Photo2A.jpg|thumb|USB keyboard and its KBC]] |
|||
|- |
|||
|[[Image:XO1.5_USBKB_Photo3.jpg|400px|Top of USB KBC]] |
|||
|Remove (unsolder) the LEDs and the crystal. |
|||
|- |
|||
|Clip the pins on the board bottom. |
|||
|[[Image:XO1.5_USBKB_Photo4.jpg|thumb|Bottom of USB KBC]] |
|||
|- |
|||
|Move the crystal to the edge of the board, extending its leads with 28ga solid wire. Be careful that you don't pull the pads off the PCB and break the traces. The copper plating is very thin! |
|||
|[[Image:XO1.5_USBKB_Photo5.jpg|thumb|Crystal after moving]] |
|||
|- |
|||
|[[Image:XO1.5_USBKB_Photo6.jpg|thumb|left|Modified USB KBC board]] |
|||
|Insulate the crystal using cellulose or polymide tape, to prevent its case from shorting, or being shorted to, other circuits in the area. Remove the stress relief and first 25cm of insulation from the USB cable. Leave the USB A end on cable for testing, for now. |
|||
|- |
|||
|Remove the plastic tabs at the top of the keyboard. |
|||
|[[Image:XO1.5_USBKB_Photo7.jpg|thumb|Keyboard tabs]] |
|||
|- |
|||
|Reattach the keyboard to the USB KBC, and retest for full functionality. |
|||
|} |
|||
==Dismantling the XO== |
|||
Make sure the laptop is running the latest firmware: q2e42 for XO-1 and q3a35 for XO-1.5. Earlier versions of firmware don't reliably detect the touchpad if there isn't a PS/2 keyboard present in the laptop. |
|||
Remove the plastic cover from the hinge between the top and bottom pieces of the XO. There are two screws in the top, holding the two pieces together. |
|||
[[Disassembly_bottom#Removing_the_handle_cover_.2F_reaching_the_spare_screws|Remove the handle cover.]] |
|||
[[Disassembly_bottom#Removing_the_hinge_.2F_disconnecting_the_top_and_bottom_halves_of_the_XO|Disconnect the top and bottom halves]] of the XO, setting the top unit aside for now. |
|||
{| |
|||
|[[Disassembly_bottom#Removing_the_keyboard|Completely disassemble the bottom half]]. '''Leave the FPC cable connected to the touchpad''' --- that connector is incredibly fragile and easy to break. |
|||
|[[Image:XO1.5_USBKB_Photo10.jpg|thumb|Upper base assembly disassembly]] |
|||
|- |
|||
|[[Image:XO1.5_USBKB_Photo12.jpg|400px|Base Assembly Components]] |
|||
|- |
|||
|Remove the keyboard and XO KBC board. |
|||
|[[Image:XO1.5_USBKB_Photo11.jpg|thumb|Keyboard Controller (w. foam)]] |
|||
|- |
|||
|Remove the waterproofing foam and rubber covering from the KBC controller. Save the rubber. |
|||
|[[Image:XO1.5_USBKB_Photo11A.jpg|thumb|Keyboard Controller PCB]] |
|||
|} |
|||
==Modifying the Keyboard Tray== |
|||
{| |
|||
|Remove any cable glue residue from the bottom of the keyboard. |
|||
|[[Image:XO1.5_USBKB_Photo15.jpg|thumb|XO Keyboard]] |
|||
|- |
|||
|Remove the keyboard membrane and two circuit layers. |
|||
|[[Image:XO1.5_USBKB_Photo16.jpg|thumb|XO Keyboard without silicone]] |
|||
|- |
|||
|[[Image:XO1.5_USBKB_Photo17.jpg|400px|Keyboard Plate Cuts]] |
|||
|- |
|||
|Cut the keyboard plate as indicated. Please grind down the edges of the cut metal to avoid personal injury. It is necessary along the edge of the keyboard tray to avoid damaging the keyboard FPC. |
|||
|[[Image:XO1.5_USBKB_Photo13.jpg|thumb|Resulting Pieces]] |
|||
|- |
|||
|We are flipping the metal plate over when making the keyboard tray, giving us another 1.5mm or so clearance for the USB keyboard. Bend the top tab of the keyboard tray. Color the sides of the keyboard tray for vanity's sake (w. marker or paint). |
|||
|[[Image:XO1.5_USBKB_Photo14.jpg|thumb|Prepared keyboard tray]] |
|||
|} |
|||
==Modifying the XO Plastic== |
|||
{| |
|||
|[[Image:XO1.5_USBKB_Photo20.jpg|320px|left|Side bumper flanges]] |
|||
|Remove the spacing flanges from the side bumpers |
|||
|- |
|||
|[[Image:XO1.5_USBKB_Photo21.jpg|thumb|right|Side bumper flanges removed]] |
|||
|- |
|||
|[[Image:XO1.5_USBKB_Photo22.jpg|320px|left|Keyboard bezel mods]] |
|||
|Remove the right threaded insert on the keyboard bezel/touchpad and surrounding bracing. |
|||
|- |
|||
|Scuff the area where the connector board is going to be glued down. Add electrical insulation to the touchpad - Kapton or electrical tape |
|||
|[[Image:XO1.5_USBKB_Photo23.jpg|thumb|right|Keyboard bezel after mods]] |
|||
|- |
|||
|[[Image:XO1.5_USBKB_Photo42.jpg|left|320px]] |
|||
|Take the laptop bottom plate (w. battery compartment) and remove the plastic bracing in the indicated locations |
|||
|- |
|||
|[[Image:XO1.5_USBKB_Photo43.jpg|thumb|right|Bottom plate after mods]] |
|||
|} |
|||
==Installing the New Keyboard== |
|||
{| |
|||
|Place the keyboard in the keyboard tray, and attach it to the keyboard bezel. Be careful not to tighten the screws at the top of the tray, as they are missing a spacer. Be careful to only use the short screws for the bottom screws of the tray. |
|||
|[[Image:XO1.5_USBKB_Photo30.jpg|thumb|Keyboard bezel w. new keyboard]] |
|||
|- |
|||
|Now play attention to the vertical fit --- it is a little tight. Gently using a file, it is possible to remove 0.3 to 0.5mm of polycarbonate from the top and bottoms of the keyboard bezel opening, improving the fit. |
|||
|[[Image:XO1.5_USBKB_Photo22B.jpg|thumb|Improving the fit]] |
|||
|- |
|||
|Once you can get the keyboard located such that no keys rub against the bezel, it is time to secure it. Either epoxy or archival glue can be used. In the case, it is important to reassemble and ensure that the keyboard is centered before it begins to cure. |
|||
|[[Image:XO1.5_USBKB_Photo29.jpg|thumb|Don't glue here]] |
|||
|} |
|||
==Hooking up the Touchpad== |
|||
{| |
|||
|[[Image:XO1.5_USBKB_Photo24.jpg|320px|right|Where to cut]] |
|||
|Remove the KBC chip from the board. Clean the pads, making sure that none are shorting. Cut the KBC board as indicated. |
|||
|- |
|||
|[[Image:XO1.5_USBKB_Photo25.jpg|thumb|right|Resulting boards]] |
|||
|- |
|||
|Check the cut edges of the connector and button boards for layer/layer shorts, and shave with XActo as needed to fix. Wire three wires (28/30 ga) between the button board and the connector board: left button, right button, and a shared ground. The right button is wired to pin 1 of the touchpad connector, and the left button is wired to pin 4. |
|||
|[[Image:XO1.5_USBKB_Photo28.jpg|200px|left]] |
|||
|- |
|||
|[[Image:XO1.5_USBKB_Photo27.jpg|200px|right]] |
|||
|} |
|||
==Installing the Connector Board== |
|||
{| |
|||
|Now attach the side bumpers. Make sure to hold the bumpers tight against the keyboard bezel when tightening the screws to ensure a minimal gap. |
|||
|[[Image:XO1.5_USBKB_Photo31.jpg|thumb|Keyboard bezel plus connector board]] |
|||
|- |
|||
|Cut and reapply the rubber membrane removed earlier from the KBC board to the touchpad buttons. Place the metal spacers cut from the keyboard, the button board, and the connector board on the keyboard bezel. |
|||
|- |
|||
|Using a small amount of epoxy or double-sided tape, secure the connector board to the keyboard bezel. If using epoxy, use cellulose or masking tape to hold it in place while drying. Make sure that you aren't stressing the touchpad cable. Once the epoxy is it is dry, remove the tape. |
|||
|[[Image:XO1.5_USBKB_Photo32.jpg|thumb|Connector board glued in place]] |
|||
|- |
|||
|Reconnect the metal tape between the touchpad grounding pad and the keyboard. Some earlier production models didn't have this tape. Use copper or aluminum tape to bridge the gap. |
|||
|[[Image:XO1.5_USBKB_Photo33.jpg|thumb|Grounding Strap]] |
|||
|- |
|||
|Attach the cable from the touchpad to the connector board, and reattach the front bumper. |
|||
|- |
|||
|Set the keyboard assembly on top of the laptop's top half, and use the "ears" to latch the two together. Attach the KBC cable from the top half to the connector board. |
|||
|[[Image:XO1.5_USBKB_Photo34.jpg|thumb|KBC attachment]] |
|||
|- |
|||
|Connect the keyboard to the USB KBC, if it isn't already. Fold the FPC as shown and use tape to secure the board to the keyboard assembly. Ensure that the grounding strap from the USB KBC is touching the keyboard tray when secured. |
|||
|[[Image:XO1.5_USBKB_Photo41.jpg|thumb|USB KBC taped in place]] |
|||
|} |
|||
Route the USB cable right next to the KBC cable, on the side nearest the bumper. |
|||
Use Kapton or cellulose tape to hold the cables securely in the correct places. |
|||
==Closing up the Base Assembly== |
|||
[[Disassembly_bottom#Replacing_the_bottom_case_cover|Insert the bottom plate into the laptop]]. Great force may be necessary! Attach it in place using the two screws into the side bumpers, holding the bumpers tight against the bottom plate when tightening. |
|||
'''Now is a good time to retest the touchpad/button/keyboard wiring'''. Plug the USB cable from the USB KBC into the laptop top half. Supply power via a power adapter. Boot the laptop, stopping in OFW by pressing the ESC key when the boot sound starts. Test the touchpad, buttton board, and connector board by typing: |
|||
ok test /mouse |
|||
==Routing the USB Connection== |
|||
Remove the back panel from the top half of the laptop (this involves [[Disassembly_top|removing the front bezel and display]]). Place the display back into the case, and hold it in place with a single screw for testing. |
|||
{| |
|||
|Cut the USB A plug from the end of the USB cable, and route the cable through the laptop hinge. It should emerge next to the existing KBC cable. |
|||
|[[Image:XO1.5_USBKB_Photo50.jpg|thumb|Routing through hinge]] |
|||
|- |
|||
|[[Disassembly_bottom#Replacing_the_hinge_.2F_Reconnecting_the_top_and_bottom_halves_of_the_XO|Reattach the hinge (and laptop top half) to the base unit]] using four screws. |
|||
|- |
|||
|Reconnect the battery cable, and place in its holder. Re-route the battery and keyboard cables into their channels. Adjust the slack in the USB cable, routing it above the battery connector! (to avoid having to modify handle cover to avoid pinching the cable) |
|||
|[[Image:XO1.5_USBKB_Photo52.jpg|thumb|USB Cable Routing]] |
|||
|} |
|||
[[Disassembly_bottom#Replacing_the_handle_cover|Reattach the back bumper and the handle cover]]. Make sure that there is a smooth fit in the front next to the keyboard. Screw the handle cover into place with five screws in the battery compartment. |
|||
===Preparing the Keyboard=== |
|||
==Hooking up the USB connection== |
|||
Test the new USB keyboard by plugging it into the XO and typing on it [[Image:XO1.5_USBKB_Photo1.jpg|thumb|Screw locations in USB keyboard]] |
|||
Ensure that the shield of the USB cable can't short against the motherboard where it exits from the hinge. (Use Kapton tape or heat shrink if necessary). The remaining steps vary depending on the laptop being modified: |
|||
Open up the USB keyboard. [[Image:XO1.5_USBKB_Photo2.jpg|thumb|USB keyboard and its KBC]] |
|||
===XO-1.5=== |
|||
Separate the keyboard controller (KBC) from the keyboard by gently pulling on the FPC. [[Image:XO1.5_USBKB_Photo2A.jpg|thumb|USB keyboard and its KBC]] [[Image:XO1.5_USBKB_Photo3.jpg|thumb|Top of USB KBC]] |
|||
{| |
|||
Remove (unsolder) the LEDs and the crystal. [[Image:XO1.5_USBKB_Photo4.jpg|100px|Bottom of USB KBC]] |
|||
|Remove the heat shield. Route the USB cable around the memory and up to R392/R393 (above the VX855 companion chip). |
|||
|[[Image:XO1.5_USBKB_Photo54.jpg|thumb|USB Cable Routing]] |
|||
|} |
|||
Cut the USB cable to length (be generous, there is room for an inch of slack). Remove the cable sheath and shielding. Use Kapton tape, electrical tape, or heat shrink tubing to ensure that there is no way the shielding can short against the motherboard. Strip and tin the four conductors. |
|||
Clip the pins on the board bottom. Move the crystal to the edge of the board, extending its leads with 28ga solid wire. Be careful that you don't pull the pads off the PCB and break the traces. The copper plating is very thin! [[Image:XO1.5_USBKB_Photo5.jpg|100px|Crystal after moving]] |
|||
{| |
|||
Insulate the crystal using cellulose or polymide tape, to prevent its case from shorting, or being shorted to, other circuits in the area. [[Image:XO1.5_USBKB_Photo6.jpg|100px|Modified USB KBC board]] |
|||
|With the motherboard in front of you so that the hinge is closest to you: Solder the black wire to the left-most pad of R393, and the white wire to the right-most pad. Solder the green wire to the left-most pad of R392 and the red wire to the right-most pad. |
|||
|[[Image:XO1.5_USBKB_Photo53.jpg|thumb|Auxiliary USB Connector]] |
|||
|} |
|||
===XO-1=== |
|||
Remove the stress relief and first 25cm of insulation (leave USB A end on cable for testing, for now). Remove the plastic tabs at the top of the keyboard. |
|||
<photo of USB keyboard tabs being removed> |
|||
If modifying an XO-1 laptop, there is no auxiliary USB connection on the motherboard. You will have to select a USB port, and wire directly to it. The USB port should somehow be blocked externally, as it can no longer be used. |
|||
Reattach the keyboard to the USB KBC, and retest it for full functionality. |
|||
== |
==Closing Up the Laptop== |
||
Apply DC power and test the operation of the keyboard and touchpad. |
|||
===Modifying the Keyboard Tray=== |
|||
Replace the heat shield, making sure that the cable isn't keeping it from firmly touching the CPU. Remove the display, replace the back plate, and [[Disassembly_top#Replacing_the_screen|reinstall the display]]. |
|||
===Hooking up the Touchpad=== |
|||
[[Disassembly_top#Replacing_the_front_panel|Reinstall the front bezel]], and the hinge cover. |
|||
''You will probably want to disable aggressive suspend/resume, as with current software releases the laptop will not wake up on USB key presses.'' |
|||
===Reassembling the XO=== |
|||
Congratulations, your warranty is now null and void! |
|||
[[Category:XO-1.5]] |
[[Category:XO-1.5]] |
Latest revision as of 21:05, 21 November 2013
NOTICE : These instructions describe how to build a prototype of a non-membrane XO-1.5 laptop, which were used as "proof of concept" before an official production variant was designed. A non-membrane keyboard is now available as an option for XO-1.5, XO-1.75 and XO-4 production and spares.
Scope
These are detailed instructions for installing a non-membrane keyboard into an XO-1.5 laptop. They apply to all pre-production as well as production models. With little change, they also apply to the later model of the XO-1 (with a single capacitive touchpad).
Credit is freely given to the author of the instructions for doing this modification to an XO-1 (part I, II), found on instructables.com.
A non-membrane keyboard is now available as an option for XO-1.5, XO-1.75 and XO-4 production and spares. The production versions use the same PS2 keyboard controller for the non-membrane keyboard as the membrane keyboard, and are much more robust and low power than the USB-based prototypes described here.
WARNING
This modification includes permanent modifications of the XO laptop, and cannot be reversed. Even if you are experienced, there is a significant chance of damaging the laptop beyond repair while following these instructions.
Material
You will need:
- An XO-1 (CL1A) or XO-1.5 (CL1B) laptop
- A micro USB keyboard (such as this one).
- A #1 screwdriver
- Fine pitch soldering equipment
- A magnifier of some sort (lens, loupe, microscope...)
- An X-Acto knife
- A small file and/or fine grade sandpaper
- A way of cutting steel and grinding plastic (such as a Dremel tool)
- cellulose (scotch) or polymide (kapton, preferred) tape
- quick drying epoxy glue or archival double-sided tape
Instructions
Preparing the Keyboard
Dismantling the XO
Make sure the laptop is running the latest firmware: q2e42 for XO-1 and q3a35 for XO-1.5. Earlier versions of firmware don't reliably detect the touchpad if there isn't a PS/2 keyboard present in the laptop.
Remove the plastic cover from the hinge between the top and bottom pieces of the XO. There are two screws in the top, holding the two pieces together.
Disconnect the top and bottom halves of the XO, setting the top unit aside for now.
Completely disassemble the bottom half. Leave the FPC cable connected to the touchpad --- that connector is incredibly fragile and easy to break. | |
![]() | |
Remove the keyboard and XO KBC board. | |
Remove the waterproofing foam and rubber covering from the KBC controller. Save the rubber. |
Modifying the Keyboard Tray
Modifying the XO Plastic
Remove the spacing flanges from the side bumpers | |
Remove the right threaded insert on the keyboard bezel/touchpad and surrounding bracing. | |
Scuff the area where the connector board is going to be glued down. Add electrical insulation to the touchpad - Kapton or electrical tape | |
Take the laptop bottom plate (w. battery compartment) and remove the plastic bracing in the indicated locations | |
Installing the New Keyboard
Place the keyboard in the keyboard tray, and attach it to the keyboard bezel. Be careful not to tighten the screws at the top of the tray, as they are missing a spacer. Be careful to only use the short screws for the bottom screws of the tray. | |
Now play attention to the vertical fit --- it is a little tight. Gently using a file, it is possible to remove 0.3 to 0.5mm of polycarbonate from the top and bottoms of the keyboard bezel opening, improving the fit. | |
Once you can get the keyboard located such that no keys rub against the bezel, it is time to secure it. Either epoxy or archival glue can be used. In the case, it is important to reassemble and ensure that the keyboard is centered before it begins to cure. |
Hooking up the Touchpad
Remove the KBC chip from the board. Clean the pads, making sure that none are shorting. Cut the KBC board as indicated. | |
Check the cut edges of the connector and button boards for layer/layer shorts, and shave with XActo as needed to fix. Wire three wires (28/30 ga) between the button board and the connector board: left button, right button, and a shared ground. The right button is wired to pin 1 of the touchpad connector, and the left button is wired to pin 4. | |
Installing the Connector Board
Now attach the side bumpers. Make sure to hold the bumpers tight against the keyboard bezel when tightening the screws to ensure a minimal gap. | |
Cut and reapply the rubber membrane removed earlier from the KBC board to the touchpad buttons. Place the metal spacers cut from the keyboard, the button board, and the connector board on the keyboard bezel. | |
Using a small amount of epoxy or double-sided tape, secure the connector board to the keyboard bezel. If using epoxy, use cellulose or masking tape to hold it in place while drying. Make sure that you aren't stressing the touchpad cable. Once the epoxy is it is dry, remove the tape. | |
Reconnect the metal tape between the touchpad grounding pad and the keyboard. Some earlier production models didn't have this tape. Use copper or aluminum tape to bridge the gap. | |
Attach the cable from the touchpad to the connector board, and reattach the front bumper. | |
Set the keyboard assembly on top of the laptop's top half, and use the "ears" to latch the two together. Attach the KBC cable from the top half to the connector board. | |
Connect the keyboard to the USB KBC, if it isn't already. Fold the FPC as shown and use tape to secure the board to the keyboard assembly. Ensure that the grounding strap from the USB KBC is touching the keyboard tray when secured. |
Route the USB cable right next to the KBC cable, on the side nearest the bumper. Use Kapton or cellulose tape to hold the cables securely in the correct places.
Closing up the Base Assembly
Insert the bottom plate into the laptop. Great force may be necessary! Attach it in place using the two screws into the side bumpers, holding the bumpers tight against the bottom plate when tightening.
Now is a good time to retest the touchpad/button/keyboard wiring. Plug the USB cable from the USB KBC into the laptop top half. Supply power via a power adapter. Boot the laptop, stopping in OFW by pressing the ESC key when the boot sound starts. Test the touchpad, buttton board, and connector board by typing:
ok test /mouse
Routing the USB Connection
Remove the back panel from the top half of the laptop (this involves removing the front bezel and display). Place the display back into the case, and hold it in place with a single screw for testing.
Cut the USB A plug from the end of the USB cable, and route the cable through the laptop hinge. It should emerge next to the existing KBC cable. | |
Reattach the hinge (and laptop top half) to the base unit using four screws. | |
Reconnect the battery cable, and place in its holder. Re-route the battery and keyboard cables into their channels. Adjust the slack in the USB cable, routing it above the battery connector! (to avoid having to modify handle cover to avoid pinching the cable) |
Reattach the back bumper and the handle cover. Make sure that there is a smooth fit in the front next to the keyboard. Screw the handle cover into place with five screws in the battery compartment.
Hooking up the USB connection
Ensure that the shield of the USB cable can't short against the motherboard where it exits from the hinge. (Use Kapton tape or heat shrink if necessary). The remaining steps vary depending on the laptop being modified:
XO-1.5
Remove the heat shield. Route the USB cable around the memory and up to R392/R393 (above the VX855 companion chip). |
Cut the USB cable to length (be generous, there is room for an inch of slack). Remove the cable sheath and shielding. Use Kapton tape, electrical tape, or heat shrink tubing to ensure that there is no way the shielding can short against the motherboard. Strip and tin the four conductors.
With the motherboard in front of you so that the hinge is closest to you: Solder the black wire to the left-most pad of R393, and the white wire to the right-most pad. Solder the green wire to the left-most pad of R392 and the red wire to the right-most pad. |
XO-1
If modifying an XO-1 laptop, there is no auxiliary USB connection on the motherboard. You will have to select a USB port, and wire directly to it. The USB port should somehow be blocked externally, as it can no longer be used.
Closing Up the Laptop
Apply DC power and test the operation of the keyboard and touchpad.
Replace the heat shield, making sure that the cable isn't keeping it from firmly touching the CPU. Remove the display, replace the back plate, and reinstall the display. Reinstall the front bezel, and the hinge cover.
You will probably want to disable aggressive suspend/resume, as with current software releases the laptop will not wake up on USB key presses.
Congratulations, your warranty is now null and void!