Talk:Notes on using the OLPC developer boards: Difference between revisions

From OLPC
Jump to navigation Jump to search
No edit summary
No edit summary
Line 1: Line 1:
Where are the specifications for the rest of the connectors on the board?
Where are the specifications for the rest of the connectors on the board?
The only two I've discerned from the Wiki so far are the obvious ones:
The only two I've discerned from the Wiki so far are the obvious ones:
* IO for serial breakout (U20? numbering unclear)
* IO for serial breakout (J1)
* CON_ANT1
* CON_ANT1
* CON_ANT2
* CON_ANT2
Line 42: Line 42:
* D22: LED. Definition changing. Same output as D2 (front/back view)
* D22: LED. Definition changing. Same output as D2 (front/back view)
* D23: LED. Definition changing. Same output as D4 (front/back view)
* D23: LED. Definition changing. Same output as D4 (front/back view)
* J1: Serial port connector. 3.3V levels. (Pin 1: 3.3V Power, 2: TxD, 3: RxD, 4: Gnd)


'''NOTE: Just because it doesn't say it's changing above, doesn't mean that it won't change!'''
'''NOTE: Just because it doesn't say it's changing above, doesn't mean that it won't change!'''

Revision as of 00:22, 30 June 2006

Where are the specifications for the rest of the connectors on the board? The only two I've discerned from the Wiki so far are the obvious ones:

  • IO for serial breakout (J1)
  • CON_ANT1
  • CON_ANT2
  • USB: CN4, CN6, CN7

Some of the development board photos show PS keyboard/mouse wired in, where would those connect? To CN23 - the pinout is shown below.

Could somebody also identify the connector type for the antenna? These are U.FL connectors.

Connectors/LEDs

  • CN1: JTAG Connector for Marvell wireless chip.
  • CN2: Old LCD Connector. Definition changing.
  • CN3: External stereo audio line output (switched)
  • CN4: USB
  • CN5: External mono microphone connector (switched)
  • CN6: USB
  • CN7: USB
  • CN8: Mono right side speaker connector
  • CN9: Internal stereo speaker connector
  • CN11: DC input jack (10V-24V; nominal 12V)
  • CN12: CRT
  • CN14: Used for DCON Debugging. Definition changing.
  • CN15: Internal microphone connector
  • CN16: AMD Geode JTAG Connector
  • CN17: Used for DCON Debugging. Definition changing.
  • CN18: CRT/LCD Jumper
  • CN19: Unused
  • CN20: Used for manufacturing (serial Flash programming)
  • CN21: Battery connector (Pin 1: Gnd, 2: VBat)
  • CN22: Battery sensor. Definition changing.
  • CN23: Internal PS/2 Connector to keyboard & input module (Pin 1: TP Data, 2: TP Clk, 3: Gnd, 4: KB Data, 5: KB Clk, 6: Power [3.3V or 5V])
  • CON1: Unused large solder pads (was mini-PCI on pre-A-Test boards)
  • D2: LED. Definition changing.
  • D3: LED. Definition changing.
  • D4: LED. Definition changing.
  • D21: LED. Definition changing. Same output as D3 (front/back view)
  • D22: LED. Definition changing. Same output as D2 (front/back view)
  • D23: LED. Definition changing. Same output as D4 (front/back view)
  • J1: Serial port connector. 3.3V levels. (Pin 1: 3.3V Power, 2: TxD, 3: RxD, 4: Gnd)

NOTE: Just because it doesn't say it's changing above, doesn't mean that it won't change!