Talk:Notes on using the OLPC developer boards: Difference between revisions

From OLPC
Jump to navigation Jump to search
(Convert back to table)
No edit summary
Line 1: Line 1:
All remaining questions are in italics. Please remove the question if you answer it!
Could somebody complete this (CN10, CN13, CN18, CN21, CN23 need info/confirmation), and move it to the main page? All questions are in italics. Pinout is wanted on a few connectors.


==Connectors/LEDs==
==Connectors/LEDs==
Line 45: Line 45:


===Front of board===
===Front of board===
{| border="1"
⚫
* CN12: CRT for developer boards only
! Code !! Name !! Description and Pinout
⚫
* CON_ANT1: U.FL connector for left? antenna
|-
* CON_ANT2: U.FL connector for right? antenna
⚫
| CN12 || CRT for developer boards only
⚫
* CN13: Wireless interface test points. Definition changing.
|-
⚫
* CN14: Used for DCON Debugging. Definition changing.
* CN15: Internal microphone connector (Pin 1: Gnd, 2: Audio)
| CON_ANT1 || U.FL connector for left? antenna || ''confirm left?''
|-
⚫
* CN16: AMD Geode JTAG Connector
⚫
| CON_ANT2 || U.FL connector for right? antenna || ''confirm right?''
⚫
* CN17: Used for DCON Debugging. Definition changing.
|-
⚫
* J1: Serial port connector. 3.3V levels. (Pin 1: 3.3V Power, 2: TxD, 3: RxD, 4: Gnd)
⚫
| CN13 || Wireless interface test points. || Definition changing.
⚫
* CN18: CRT/LCD Jumper - 1/3 = CRT, Removed = LCD
|-
⚫
* CN19: Unused and unsoldered jumper.
⚫
| CN14 || Used for DCON Debugging. || Definition changing.
⚫
* CN20: Used for manufacturing (serial Flash programming). Requires special fixture.
|-
⚫
* CN21: Battery connector (Pin 1: Gnd, 2: VBat). Battery is 5-cell NiMH, nominal ~6.0V.
| CN15 || Internal microphone connector || (Pin 1: Gnd, 2: Audio)
⚫
* CN22: Battery sensor. Definition changing.
|-
⚫
* CN23: Internal PS/2 Connector to keyboard & input module (Pin 1: TP Data, 2: TP Clk, 3: Gnd, 4: KB Data, 5: KB Clk, 6: Power). Power is 5V if L36 populated, 3.3V if L37. L36/L37 located above pin 6.
⚫
| CN16 || AMD Geode JTAG Connector
⚫
* D21: LED. Definition changing. Same output as D3 (front/back view).
|-
⚫
* D22: LED. Definition changing. Same output as D2 (front/back view).
⚫
| CN17 || Used for DCON Debugging. || Definition changing.
⚫
* D23: LED. Definition changing. Same output as D4 (front/back view).
|-
⚫
| J1 || Serial port connector. || 3.3V levels. (Pin 1: 3.3V Power, 2: TxD, 3: RxD, 4: Gnd)
|-
⚫
| CN18 || CRT/LCD Jumper || 1/3 = CRT, Removed = LCD
|-
⚫
| CN19 || Unused and unsoldered jumper.
|-
⚫
| CN20 || Used for manufacturing || Serial Flash programming. Requires special fixture.
|-
⚫
| CN21 || Battery connector || (Pin 1: Gnd, 2: VBat). Battery is 5-cell NiMH, nominal ~6.0V.
|-
⚫
| CN22 || Battery sensor. || Definition changing.
|-
⚫
| CN23 || Internal PS/2 Connector<br /> to keyboard & input module || (Pin 1: TP Data, 2: TP Clk, 3: Gnd, 4: KB Data, 5: KB Clk, 6: Power).<br />Power is 5V if L36 populated, 3.3V if L37. L36/L37 located above pin 6.
|-
⚫
| D21 || LED. || Definition changing. Same output as D3 (front/back view).
|-
⚫
| D22 || LED. || Definition changing. Same output as D2 (front/back view).
|-
⚫
| D23 || LED. || Definition changing. Same output as D4 (front/back view).
|}

Revision as of 00:45, 3 July 2006

All remaining questions are in italics. Please remove the question if you answer it!

Connectors/LEDs

  • All of these numbers are allocated starting top left corner, allocated in scanline fashion.
  • The front of the board is the side with the VGA connector and the Geode processor.

Warnings

  • Just because it doesn't say it's changing, doesn't mean that it won't change!
  • Do NOT confuse J1 with CN9! You will fry the audio!
  • Do NOT populate both L36 and L37! (see CN23 PS/2 connector).

Back of board

Code Name Description and Pinout
CN1 JTAG Connector for Marvell wireless chip
CN2 Old LCD Connector Definition changing.
CN3 External stereo audio line output (switched)
CN4 USB
CN5 External mono microphone connector (switched)
CN6 USB
CN7 USB
CN8 Mono right side speaker connector (Pin 1: Right +, 2: Right -)
CN9 Internal stereo speaker connector (Pin 1: Left -, 2: Left +, 3: Right -, 4: Right +)
CN10 No longer exists (2-pin CN9 and CN10 were combined to 4-pin CN9)
CN11 DC input jack (10V-24V; nominal 12V) Center positive.
CON1 Unused large solder pads (was mini-PCI on pre-A-Test boards)
D2 LED. Definition changing. Same output as D22 (front/back view).
D3 LED. Definition changing. Same output as D21 (front/back view).
D4 LED. Definition changing. Same output as D23 (front/back view).

Front of board

Code Name Description and Pinout
CN12 CRT for developer boards only
CON_ANT1 U.FL connector for left? antenna confirm left?
CON_ANT2 U.FL connector for right? antenna confirm right?
CN13 Wireless interface test points. Definition changing.
CN14 Used for DCON Debugging. Definition changing.
CN15 Internal microphone connector (Pin 1: Gnd, 2: Audio)
CN16 AMD Geode JTAG Connector
CN17 Used for DCON Debugging. Definition changing.
J1 Serial port connector. 3.3V levels. (Pin 1: 3.3V Power, 2: TxD, 3: RxD, 4: Gnd)
CN18 CRT/LCD Jumper 1/3 = CRT, Removed = LCD
CN19 Unused and unsoldered jumper.
CN20 Used for manufacturing Serial Flash programming. Requires special fixture.
CN21 Battery connector (Pin 1: Gnd, 2: VBat). Battery is 5-cell NiMH, nominal ~6.0V.
CN22 Battery sensor. Definition changing.
CN23 Internal PS/2 Connector
to keyboard & input module		 (Pin 1: TP Data, 2: TP Clk, 3: Gnd, 4: KB Data, 5: KB Clk, 6: Power).
Power is 5V if L36 populated, 3.3V if L37. L36/L37 located above pin 6.
D21 LED. Definition changing. Same output as D3 (front/back view).
D22 LED. Definition changing. Same output as D2 (front/back view).
D23 LED. Definition changing. Same output as D4 (front/back view).
Retrieved from "http://wiki.laptop.org/mediawiki/index.php?title=Talk:Notes_on_using_the_OLPC_developer_boards&oldid=7956"