Manual Firmware Install: Difference between revisions

From OLPC
Jump to navigation Jump to search
(consistency of command blocks with other pages)
 
(18 intermediate revisions by 3 users not shown)
Line 1: Line 1:
<noinclude>''Note: Many firmware pages transclude this page to provide installation instructions, providing a version in place of VERSION_NUM; see e.g. [[OLPC Firmware q2e15]].</noinclude>
<noinclude>''Note: Many firmware pages transclude this page to provide installation instructions, providing a version in place of VERSION_NUM; see e.g. [[OLPC Firmware q2e15]].
{{developers}}</noinclude>

==Installation==
==Installation==
When installing new firmware, you must have a well-charged battery and the AC adapter plugged in. The firmware update code will not proceed otherwise. Possible error messages are:


{| border="1" cellspacing="0" cellpadding="2" width="100%" class="wikitable"
When installing new firmware, you must have a well-charged battery and the AC adapter plugged in. The firmware update code will not proceed otherwise. "AC not present" means you need to plug it in.
! error message
! how to fix
|-
| ''AC not present''
| plug in the power cord, check the battery LED is on, then try again.
|-
| ''No external power''
| plug in the power cord, check the battery LED is on, then try again,
|-
| ''No battery''
| plug in the battery, check the latches, then try again, or try another battery,
|-
| ''Battery low''
| allow more time for the battery to charge, then try again, or try another battery.
|}


===Unsecured Machines===
===Unsecured Laptop===


''This section is for unsecured laptops. Most XO-1.5 laptops are unsecured. Most developer XO laptops are unsecured. To unsecure your laptop, follow the instructions at [[Activation and Developer Keys]].''
''This section is for unsecured laptops. Most XO-1.5 and XO-1.75 laptops are unsecured. Most developer XO laptops are unsecured. To unsecure your laptop, follow the instructions at [[Activation and Developer Keys]].''


You may install using either:
You may install using either:
Line 28: Line 46:


*turn on the laptop, and get to the 'ok' prompt. See [[Ok]] for more detail. You should see:
*turn on the laptop, and get to the 'ok' prompt. See [[Ok]] for more detail. You should see:

ok
ok


*if the downloaded file is on a USB drive, type:
*if the downloaded file is on a USB drive, type:
ok flash u:\{{{version|VERSION_NUM}}}.rom
flash u:\{{{version|VERSION_NUM}}}.rom


*if the downloaded file is on an external SD card:
*if the downloaded file is on an external SD card:
ok flash sd:\boot\{{{version|VERSION_NUM}}}.rom
flash sd:\boot\{{{version|VERSION_NUM}}}.rom


*wait for the laptop to reboot itself,
*wait for the laptop to reboot itself,


*remove the USB drive or SD card.
*remove the USB drive or SD card.

(Expert users may remove the USB drive after the message "''Got firmware''" ... at this stage the file has been read and closed.)


==== Using the laptop internal drive ====
==== Using the laptop internal drive ====
Line 55: Line 74:
wget http://dev.laptop.org/pub/firmware/{{{version|VERSION_NUM}}}/{{{version|VERSION_NUM}}}.rom
wget http://dev.laptop.org/pub/firmware/{{{version|VERSION_NUM}}}/{{{version|VERSION_NUM}}}.rom


*[[shutdown]] the laptop,
*prepare the laptop and obtain the [[Ok]] prompt as described above,

*check the battery is inserted and locked,

*check that the power cord is in place and the battery indicator is green,

*turn on the laptop, and get to the 'ok' prompt. See [[Ok]] for more detail. You should see:
ok


*if the downloaded file is on an XO-1, type:
*if the downloaded file is on an XO-1, type:
ok flash n:\boot\{{{version|VERSION_NUM}}}.rom
flash n:\boot\{{{version|VERSION_NUM}}}.rom


*if the file is on the internal SD card of an XO-1.5:
*if the file is on the internal SD card of an XO-1.5 or XO-1.75:
ok flash int:\boot\{{{version|VERSION_NUM}}}.rom
flash int:\boot\{{{version|VERSION_NUM}}}.rom


==== Using a network ====
==== Using a network ====


You will need an open wireless access point, connected to the internet.
You will need a compatible USB to ethernet adapter, or an open or WEP wireless access point, connected to the internet.

*[[shutdown]] the laptop,

*check the battery is inserted and locked,

*check that the power cord is in place and the battery indicator is green,

*turn on the laptop, and get to the 'ok' prompt. See [[Ok]] for more detail. You should see:
ok


*if using wireless, type the essid of the wireless network:
*prepare the laptop and obtain the [[Ok]] prompt as described above,
essid mynetwork


*type the essid of the wireless network:
*if using a WPA wireless access point, type the WPA key for the network:
wpa passphrase
ok essid mynetwork


*type the flash command using the download link, but ''change all slash characters so they are backwards'', for example:
*type the flash command using the download link above, but ''change all slash characters so they are backwards'', for example:
ok flash http:\\dev.laptop.org\pub\firmware\q3ann\q3ann.rom
flash http:\\dev.laptop.org\pub\firmware\{{{version|VERSION_NUM}}}\{{{version|VERSION_NUM}}}.rom


===Secured Machines===
===Secured Laptop===
Secured laptops can only use flash firmware that has been signed.
Pre-mass-production machines were almost all unsecured.
Secure-mode machines can only use flash firmware that has been signed.
All mass-production machines had the latest firmware at the time of manufacture.
All mass-production machines had the latest signed firmware at the time of manufacture installed.


[[Upgrading firmware]] describes how to upgrade to a newer official (signed) firmware release.
[[Upgrading firmware]] describes how to upgrade to a newer signed firmware release.


== See also ==
== See also ==

Latest revision as of 01:21, 17 September 2013

Note: Many firmware pages transclude this page to provide installation instructions, providing a version in place of VERSION_NUM; see e.g. OLPC Firmware q2e15.

Installation

When installing new firmware, you must have a well-charged battery and the AC adapter plugged in. The firmware update code will not proceed otherwise. Possible error messages are:

error message how to fix
AC not present plug in the power cord, check the battery LED is on, then try again.
No external power plug in the power cord, check the battery LED is on, then try again,
No battery plug in the battery, check the latches, then try again, or try another battery,
Battery low allow more time for the battery to charge, then try again, or try another battery.

Unsecured Laptop

This section is for unsecured laptops. Most XO-1.5 and XO-1.75 laptops are unsecured. Most developer XO laptops are unsecured. To unsecure your laptop, follow the instructions at Activation and Developer Keys.

You may install using either:

  • a USB drive or SD card,
  • the laptop's internal drive,
  • a network.

Choose one.

Using a USB drive or SD card

  • check the battery is inserted and locked,
  • check that the power cord is in place and the battery indicator is green,
  • insert the USB drive or SD card,
  • turn on the laptop, and get to the 'ok' prompt. See Ok for more detail. You should see:
ok
  • if the downloaded file is on a USB drive, type:
 flash u:\VERSION_NUM.rom
  • if the downloaded file is on an external SD card:
 flash sd:\boot\VERSION_NUM.rom
  • wait for the laptop to reboot itself,
  • remove the USB drive or SD card.

(Expert users may remove the USB drive after the message "Got firmware" ... at this stage the file has been read and closed.)

Using the laptop internal drive

An alternate method is to download the firmware file to the laptop internal drive and then install from the internal drive.

  • start the laptop,
  • connect to a wireless or wired network,
su
cd /versions/boot/current/boot/
wget http://dev.laptop.org/pub/firmware/VERSION_NUM/VERSION_NUM.rom
  • check the battery is inserted and locked,
  • check that the power cord is in place and the battery indicator is green,
  • turn on the laptop, and get to the 'ok' prompt. See Ok for more detail. You should see:
ok
  • if the downloaded file is on an XO-1, type:
flash n:\boot\VERSION_NUM.rom
  • if the file is on the internal SD card of an XO-1.5 or XO-1.75:
flash int:\boot\VERSION_NUM.rom

Using a network

You will need a compatible USB to ethernet adapter, or an open or WEP wireless access point, connected to the internet.

  • check the battery is inserted and locked,
  • check that the power cord is in place and the battery indicator is green,
  • turn on the laptop, and get to the 'ok' prompt. See Ok for more detail. You should see:
ok
  • if using wireless, type the essid of the wireless network:
essid mynetwork
  • if using a WPA wireless access point, type the WPA key for the network:
wpa passphrase
  • type the flash command using the download link above, but change all slash characters so they are backwards, for example:
flash http:\\dev.laptop.org\pub\firmware\VERSION_NUM\VERSION_NUM.rom

Secured Laptop

Secured laptops can only use flash firmware that has been signed. All mass-production machines had the latest firmware at the time of manufacture.

Upgrading firmware describes how to upgrade to a newer signed firmware release.

See also

  • Cheat codes for information about how game buttons control startup options.