Oscilloscope adaptor: Difference between revisions

From OLPC
Jump to navigation Jump to search
(New page: =Goal: To take input from .3-16 to .3-2.0v= ==Ideas:== * Use a resistor-based voltage divider that divides by eight, reducing 16 volts to 2 volts. * Use a 2.2v zener diode with a voltage d...)
 
No edit summary
 
(2 intermediate revisions by the same user not shown)
Line 1: Line 1:
=Goal: To take input from .3-16 to .3-2.0v=
=Goal: To take input from .3-16v to .3-2.0v=
==Ideas:==
==Ideas:==
===Voltage Divider w/ Zener===
* Use a resistor-based voltage divider that divides by eight, reducing 16 volts to 2 volts.
* Use a resistor-based voltage divider that divides by eight, reducing 16 volts to 2 volts.
** Using precision surface-mount resistors on a PCB with a heat-sink
* Use a 2.2v zener diode with a voltage dependent switch to enable the measuring of voltages less than 2.4v(.3*8)
*** Use body of probe as heatsink, if conductive enough.
[[User:DyD|DyD]] 13:40, 20 September 2007 (EDT)
* Use a 2v zener diode with a voltage dependent switch to enable the measuring of voltages less than 2.4v(.3*8)
** This method would require the child to recognize high(above 1.9v) and low(below 1.9v) voltages, and to adjust a switch accordingly.

==Prototype==
[[Image:Voltage divider.png|||100px|Schematic of a resistor divider. ''R''<sub>1</sub> is connected to ''V''<sub>in</sub> and ''V''<sub>out</sub>, ''R''<sub>2</sub> is connected to ''V''<sub>out</sub> and GND]]
* Using a voltage divider like the one imaged above, I set the values of ''R''<sub>1</sub> to be 700 ohms, and ''R''<sub>2</sub> to be 100 ohms, according to the formula: ''V''<sub>out</sub>=''V''<sub>in</sub>*(''R''<sub>2</sub>/(''R''<sub>2</sub>+''R''<sub>1</sub>))
** This gives me a simple voltage divider which divides by a factor of 8
* I then plan on having a simple switch to switch the path of the input from the voltage divider to a 2v Zener diode.
[[Category:Hardware ideas]]
[[Category:Hardware]]

Latest revision as of 14:48, 22 September 2007

Goal: To take input from .3-16v to .3-2.0v

Ideas:

Voltage Divider w/ Zener

  • Use a resistor-based voltage divider that divides by eight, reducing 16 volts to 2 volts.
    • Using precision surface-mount resistors on a PCB with a heat-sink
      • Use body of probe as heatsink, if conductive enough.
  • Use a 2v zener diode with a voltage dependent switch to enable the measuring of voltages less than 2.4v(.3*8)
    • This method would require the child to recognize high(above 1.9v) and low(below 1.9v) voltages, and to adjust a switch accordingly.

Prototype

Schematic of a resistor divider. R1 is connected to Vin and Vout, R2 is connected to Vout and GND

  • Using a voltage divider like the one imaged above, I set the values of R1 to be 700 ohms, and R2 to be 100 ohms, according to the formula: Vout=Vin*(R2/(R2+R1))
    • This gives me a simple voltage divider which divides by a factor of 8
  • I then plan on having a simple switch to switch the path of the input from the voltage divider to a 2v Zener diode.