XS Installing Software 0.6: Difference between revisions

From OLPC
Jump to navigation Jump to search
(remove latest releases table, it does not serve any purpose here and is a distraction)
 
(142 intermediate revisions by 43 users not shown)
Line 1: Line 1:
{{translations}}
{{OLPC}}
{{OLPC}}
[[Category:Software]]
[[Category:Software]]
Line 4: Line 5:
[[Category:SchoolServer]]
[[Category:SchoolServer]]


This page describes how to obtain a copy of the [[XS_Server_Software|XS school server software]], load it onto media, and install it onto a system. A more [[XS Software Repositories|complete description of the software repositories]], and [[Schoolserver_Testing|tasting instructions]] are available.
This page describes how to obtain a copy of the [[XS_Server_Software|XS school server software]], load it onto media, and install it onto a system.


This page covers '''XS 0.6 and newer'''. For older releases, see
=Downloading the System Image=


* [[XS_Installing_Software_0.5]]
* [[XS_Installing_Software_0.4]]

=Downloading the System Image=
You can obtain the latest image from [http://xs-dev.laptop.org/xs/ http://xs-dev.laptop.org/xs/]:
You can obtain the latest image from [http://xs-dev.laptop.org/xs/ http://xs-dev.laptop.org/xs/]:


wget http://xs-dev.laptop.org/xs/OLPC_XS_LATEST.iso
wget http://dev.laptop.org/xs/OLPC-School-Server-0.6-i386.iso


This can be copied onto a CD or DVD using your favorite software.
This can be copied onto a '''CD''' or '''DVD''' using your favorite software.


You can also [[XS_Techniques_and_Configuration#Installing_from_USB|install it from USB]] (warning: unsupported!)
It may also be copied onto a USB key, using the <tt>livecd-tools</tt> provided by Fedora 7:

livecd-iso-to-disk OLPC_XS_LATEST.iso /dev/sdb1

where <tt>/dev/sdb1</tt> represents the USB key being copied onto.

==Using an XO to create an installer USB key==

You can use an XO laptop to create an installer key. First, you will need to install some necessary tools on the XO, then download the image, then transfer it to a USB key inserted in the laptop:

sudo yum install livecd-tools
wget http://xs-dev.laptop.org/xs/OLPC_XS_LATEST.iso
sudo livecd-iso-to-disk OLPC_XS_LATEST.iso /dev/sda1


=Installing the Software=
=Installing the Software=


'''Please read the [[XS Release Notes|release notes]] for the version you are installing.'''
The install from a CD or USB key will eventually be automatic upon booting. While the install is currently mostly automated (not interactive), it is not performed automatically upon boot.


The install from a '''CD''' or '''USB''' storage device will eventually be automatic upon booting. While the install is currently mostly automated (not interactive), it is not performed automatically upon boot.
# Boot from the USB Key or CD-ROM -- Getting an older system to boot from a USB key can be difficult, but most will do it.
# Select "Run from Image" at the initial boot screen.
# When it has finished booting, login as root (no password is required) and type:
./olpc-install
# You will be prompted for the keyboard type, the time zone, and a root password
# If the disk in the system is new, you may be prompted to OK its formatting.
# When it has finished installing, you will need to reboot. The installer will erroneously tell you it is rebooting, but you will have to manually type <tt>reboot</tt>. Remove the CD-ROM or USB key after power-down, but before the boot process begins.


# Boot from the USB device or CD-ROM.
You should now have a machine which somewhat resembles a school server.
# Press enter to start the graphical boot menu.
# Select "Install using kickstart" at the initial boot screen.
## "Install using kickstart" is the last menu item. Do not use the other "Install" options on this menu as they only install Fedora 9 without the olpc scripts. The Anaconda installer will install around 546 packages. If it announces it is installing 407 packages, the olpc scripts are missing. Start again.
# '''Note: the default graphical installer can be unstable at times. You can press tab and add 'text' at the end of the line to request the text-based installer.'''
# Anaconda (the Fedora installer) takes over and you will be prompted for the standard questions - these are preset to the correct defaults for the School Server configuration. You will want to set keyboard type, the time zone, and a root password for your specific system.
## If you are planning to deploy to a large number of XSs, it is easy to modify the Kickstart file to have the whole process run automatically.
# When prompted to add specific packages, just leave the default and click next.
# When it has finished installing, you will be prompted to reboot. Remove the CD-ROM or USB device after power-down, but before the boot process begins.


You should now have a School Server! It needs initial configuration before it starts providing services to the laptops.
===Booting from a USB key===


== Automating the Install ==
In our experience, most generic x86 computers equipped with USB ports support booting from a USB storage device (a ''USB key''). Almost none are configured to do so automatically. This can easily be forced from the BIOS.


If you want to install XS software using a cobbler-based Installation Server, please see [[XS_Install_Server]].
====Phoenix BIOS====


== Installing on an XO ==
# Insert the USB key into the machine before booting
# Enter the BIOS by pressing ''DEL'' on a keyboard during the initial boot process.
# Select "Advanced BIOS Features"
# Select "Hard Disk Boot Priority"
# You should see your USB key listed as a boot device. Move it to the top by selecting it and pressing ''PgUp''.
# If you don't see your USB key listed, move "Bootable Add-in Cards" to the top of the list. But remember to move it back down after installation, or your system may not boot!
# Save the BIOS parameters to CMOS and reboot by pressing ''F10'', then ''Enter''


If you are wanting to run the XS software on an XO, please see [[XS-on-XO]].
====Dell====


= Initial Configuration =
''Coming soon''


== Setting hostname and domain ==
== Configuration ==
Login as root, with whatever password you assigned during installation.


Right after installation, you '''must'''
The default server setup is to connect to the Internet on the first wired ethernet network interface, using IPv4 DHCP. Laptops connect to the server over the wireless mesh using one or more [[Active Antenna]], connected through USB interfaces. Optional second (and additional) ethernet interfaces are configured by default to provide an internal LAN within the school. Traditional WiFi access points, if used, should be located on this internal LAN. See [[XS Configuration Management]] for details.
* Set the server domain name (the hostname is always 'schoolserver') using:
/etc/sysconfig/olpc-scripts/domain_config example.org
* Reboot the machine so the hostname change can take effect:
reboot
* Installation and initial configuration are complete!


== What next? ==
To enable external IPv6 you will have to [[XS_Configuration_Management#IPv6|configure the global address of the machine and setup an IPv6 tunnel]].


'''Important: Register an XO and visit the Schoolserver'''. You should do this with the XO of a teacher or school principal, as the first XO to visit the Schoolserver will have the "course creator" role. [[XS Techniques and Configuration#Moodle|More about Moodle]]
== Installing additional software ==
All the topics below are discussed in [[XS Techniques and Configuration]]


* Setting a static IP address for eth0, or using something other than eth0 as your WAN port.
If you wish to install packages that aren't part of the default school server distribution, you should first try using <tt>yum</tt>. The ''stable'' and ''testing'' school server repositories include all packages included in Fedora, even if they aren't installed by default. For third party software, such as Moodle, you should follow their installation procedure for Fedora 7
* Using specific DNS servers (from your ISP, or from OpenDNS -recommended!)
* You may want to enable the transparent HTTP proxy.
* and more...


=Network Configuration Notes=
=Upgrading=


The default server setup is to connect to the Internet on the '''first wired ethernet network interface''', using IPv4 DHCP. Laptops connect to the server over Access Points (APs) connected to the '''second wired ethernet network interface''' or via the wireless mesh using one or more [[Active Antenna]], connected through USB interfaces.
Upgrading a server is done using the [http://linux.duke.edu/yum/ <tt>yum</tt>] package interface provided by Fedora.


If your XS has 2 network interfaces and you would like to reverse their (WAN, LAN) roles, or if you only have one network interface and would like to swap it's role, you can use the xs-swapnics utility. If you get your WAN via some other interface (e.g., ppp0) then you will want to see the [[XS_Techniques_and_Configuration#Using_a_different_WAN_connection|recipes for WAN connections]].
==Over the Internet==


IPv6 is not enabled by default and not needed -- to enable external IPv6 you will have to [[XS_Configuration_Management#IPv6|configure the global address of the machine and setup an IPv6 tunnel]].
If you have an Internet connection, you can upgrade from the default servers at OLPC, or your own mirrors of them. This is done using yum:


The XS runs a fully-fledged DNS server internally, therefore there is no need to enter the DNS servers from your ISP into the configuration. If you do want the XS to use specific DNSs, see the instructions on [[XS_Techniques_and_Configuration#Use_ISP-provided_DNS_servers|using ISP-provided DNS servers]]
sudo yum -y upgrade


==From a CD or USB key==
== Access Points ==


[[Image:XS_Usage_APNormal.png|600px]]
If you do not have an Internet connection (or wish to minimize its use), you can obtain a CD or USB key for upgrading an existing system.


Most access points are compatible with the XO. For a list of ones which have been shown to work see [[Wireless Access Point Compatibility]]. Unless a single access point is being used (not recommended for more than forty to fifty laptops), a network switch of some sort will also be needed.
''More instructions coming soon. Feel free to contribute''


Make sure your AP is configured to act as an Access Point, with no added features or smarts. The AP should not be a DHCP server and should not act as a router.
=Release Notes=


Some tips on configuring APs at [[XS_Techniques_and_Configuration]].
Please read these notes to understand the capabilities and known problems with a particular release of the XS school server software. The latest release of software is described first, with a selection of earlier releases also described for completeness.


== Active Antennae ==
==OLPC_XS_141==
'''Important note: Active Antennae is not supported or available from OLPC at this time'''


If you have active antenna(e) to use, simply plug them in and reboot the XS. It will detect them and allocate them to mshbond0, mshbond1 and mshbond2. It should just work and XOs will see "School server mesh" when they connect to the mesh served by the XS. You may need to manually allocate different frequencies per antenna.
This release provides the latest firmware and drivers for the Active Antennas, fixing a problem with large file transfers over the mesh. All users of earlier XS software builds are strongly encouraged to upgrade!


=More configuration options=
WLAN Firmware: '''20.p47''' Kernel: '''2.6.23.1-23.fc7''' xs-config: '''0.2.2-4'''


For more information on keeping your XS up to date, Internet content filtering, alternative networking/routing setups, and a lot of other advanced configuration topics see [[XS_Techniques_and_Configuration]].
[http://xs-dev.laptop.org/xs/ Download Here]


=Upgrading=
===Known Problems===
* Plenty of functionality still missing, such as [[Ejabberd_Configuration|ejabberd]] and web caching
* The idmgr is not installed. To install and start it, type:
yum install idmgr
* Netplugd is disabled at this time. It interacts badly with the the current libertas driver, and causes crashes, lack of network, etc. This doesn't seem to affect anything right now, but is an unplanned change.


===Upgrading from earlier releases===
==Upgrade from XS 0.5 or later==


With the full ISO:
This should work, with a few caveats:
* The process is similar to a new (anaconda based) installation. Download the iso, and boot it...
* In the menu shown right after booting, you choose one of the 'Install or upgrade an existing system'.
* At the 'Install new or upgrade' screen choose upgrade.
* Reboot, and complete the 'steps after upgrade'.


With <code>yum</code>:
====Disable Netplugd service====
You will need to manually turn off netplugd until we figure out why it is unhappy with the latest libertas driver:
chkconfig netplugd off
service netplugd stop


* Clean yum's caches
====Reconfiguration of Network====
yum clean all
To avoid disturbing any manual configuration of the server network interfaces, hot-plug of the Active Antennas will not be supported on an upgraded machine until the network configuration script is run manually (which will require reconfiguring the WAN interface):
* Swith to the new repositories
/etc/sysconfig/olpc-scripts/network-config.py
rpm -Uvh http://xs-dev.laptop.org/xsrepos/stable/olpc/xs-0.6/i386/xs-release-9-0.4.15.2.ga69303f.noarch.rpm
After running this script, any manually configured network scripts (in <tt>/etc/sysconfig/network-scripts/</tt>) such as the WAN configuration will be saved with a <tt>.bak</tt> suffix. Reboot immediately after running the <tt>network-config.py</tt> script.
* Check that the new repositories have not been installed as "rpmnew":
ls /etc/yum.repos.d/*rpmnew
* Run the install!
yum update
* Reboot, and complete the 'steps after upgrade'.


Steps after upgrade:
==OLPC_XS_137==
* Re-run the /etc/sysconfig/olpc-scripts/domain_config script with the appropriate domain name for the machine.
This release supports hot-plug of the Active Antennas (unplugging and plugging while the server is running.) It also provides the latest firmware and drivers for the Active Antennas, fixing a number of stability problems and avoiding a problem where the mesh interacted badly with conventional 802.11b/g access points running a Broadcom chipset (such as the Linksys WRT54G).
* Ensure the right Postgres is set to run
chkconfig --level 345 postgresql off
chkconfig --add pgsql-xs


==Upgrade from XS 0.4 or earlier==
===Known Problems===
* Plenty of missing functionality.


If you are upgrading from XS 0.4 or earlier, the process is similar to a new installation, with some minor changes. In the menu shown right after booting, you should choose one of the 'Install or upgrade an existing system' options, press the Tab key, and add 'upgradeany' to the boot configuration line. After adding that line, press enter twice.
===Upgrading from earlier releases===


With this extra option, Anaconda will recognise the old installation and will offer to upgrade.
This has been tested and should work fine, with one intentional exception:


Steps after upgrade:
To avoid disturbing any manual configuration of the server network interfaces, hot-plug of the Active Antennas will not be supported on an upgraded machine until <tt>/etc/sysconfig/olpc-scripts/network-config.py</tt> is run manually. After running this script, any manually configured network scripts (in <tt>/etc/sysconfig/network-scripts/</tt>) will be saved with a <tt>.bak</tt> suffix.
* Re-run the /etc/sysconfig/olpc-scripts/domain_config script with the appropriate domain name for the machine.
* Ensure the right Postgres is set to run
chkconfig --level 345 postgresql off
chkconfig --add pgsql-xs


Notes:
==OLPC_XS_128==
* The new OS may detect your network cards differently -- the roles of WAN and LAN cards may end up swapped from what they were under 0.4. If that happens, use the xs-swapnics script and reboot.
This release has the registration server required for Trial3, as well as a fix to the inittab script which caused problems in India.


= See also =
==OLPC_XS_127==
* [[XS Techniques and Configuration]]
A bug fix release, due to our lame QA department not testing build 126 on a server with a single wired interface before release. This fixes the network configuration problems in 125 and 126 on servers with a single wired interface.
* [[XS Troubleshooting]]


[[Category:SchoolServer]]
==OLPC_XS_126==
A bug fix release. This fixes the mesh channel assignment and network configuration problems in 125

==OLPC_XS_125==
This release has basic network functionality. It supports laptops on the mesh.

It does NOT autoinstall automatically. You will need to login as root (no password), then run <tt>/root/olpc-install</tt>. You will be prompted for a root password, otherwise the installation is automatic.

Missing:
* Registration
* Web services
* Presence service
* A configuration interface
* Lots more...

Known Problems:
* /etc/named.conf isn't being installed correctly from the xs-config RPM. The fix is:
cp /etc/named.conf.olpcnew /etc/named.conf
* Hotplug of the mesh interfaces doesn't trigger a restart of the olpc-mesh-config, which is needed for the mesh to work.
* SELinux is left in permissive mode, instead of completely disabled. Edit <tt>/etc/selinux/config</tt> and set <tt>SELINUX=disabled</tt>
* The channel on the mesh interface isn't being set correctly. This causes problems with XO builds later than 542. Set the channel manually using iwconfig for now. Fixed in build 126.
* The network configuration script could fail and assign a mesh interface as the WAN. Fixed in build 127.
* On machines with no serial port, there might be a problem resulting in an error message on the console: <tt>INIT : Id "s0" respawning too fast : disabled for 5 minutes</tt>. This is fixed in xs-config v0.1.7-4, (not currently in any live CD build).

The most common problem with the mesh is due to a hardware problem with the Marvell wireless modules used in the Active Antennas. They frequently do not reset properly, and need to be power cycled. The symptom is that you will get a message: "libertas: Unable to init firmware" on the console, and <tt>ifconfig</tt> won't show a mesh interface. A reboot will not fix the situation, you need to actually power cycle the USB adapter by unplugging it and plugging it back in.

Latest revision as of 21:56, 5 August 2013

  english | españolCopy "{{subst:requesttranslation}}" to 한국어 HowTo [ID# 290708]  +/-  


  This page is monitored by the OLPC team.

This page describes how to obtain a copy of the XS school server software, load it onto media, and install it onto a system.

This page covers XS 0.6 and newer. For older releases, see

Downloading the System Image

You can obtain the latest image from http://xs-dev.laptop.org/xs/:

wget http://dev.laptop.org/xs/OLPC-School-Server-0.6-i386.iso

This can be copied onto a CD or DVD using your favorite software.

You can also install it from USB (warning: unsupported!)

Installing the Software

Please read the release notes for the version you are installing.

The install from a CD or USB storage device will eventually be automatic upon booting. While the install is currently mostly automated (not interactive), it is not performed automatically upon boot.

  1. Boot from the USB device or CD-ROM.
  2. Press enter to start the graphical boot menu.
  3. Select "Install using kickstart" at the initial boot screen.
    1. "Install using kickstart" is the last menu item. Do not use the other "Install" options on this menu as they only install Fedora 9 without the olpc scripts. The Anaconda installer will install around 546 packages. If it announces it is installing 407 packages, the olpc scripts are missing. Start again.
  4. Note: the default graphical installer can be unstable at times. You can press tab and add 'text' at the end of the line to request the text-based installer.
  5. Anaconda (the Fedora installer) takes over and you will be prompted for the standard questions - these are preset to the correct defaults for the School Server configuration. You will want to set keyboard type, the time zone, and a root password for your specific system.
    1. If you are planning to deploy to a large number of XSs, it is easy to modify the Kickstart file to have the whole process run automatically.
  6. When prompted to add specific packages, just leave the default and click next.
  7. When it has finished installing, you will be prompted to reboot. Remove the CD-ROM or USB device after power-down, but before the boot process begins.

You should now have a School Server! It needs initial configuration before it starts providing services to the laptops.

Automating the Install

If you want to install XS software using a cobbler-based Installation Server, please see XS_Install_Server.

Installing on an XO

If you are wanting to run the XS software on an XO, please see XS-on-XO.

Initial Configuration

Setting hostname and domain

Login as root, with whatever password you assigned during installation.

Right after installation, you must

  • Set the server domain name (the hostname is always 'schoolserver') using:
/etc/sysconfig/olpc-scripts/domain_config example.org
  • Reboot the machine so the hostname change can take effect:
reboot
  • Installation and initial configuration are complete!

What next?

Important: Register an XO and visit the Schoolserver. You should do this with the XO of a teacher or school principal, as the first XO to visit the Schoolserver will have the "course creator" role. More about Moodle

All the topics below are discussed in XS Techniques and Configuration

  • Setting a static IP address for eth0, or using something other than eth0 as your WAN port.
  • Using specific DNS servers (from your ISP, or from OpenDNS -recommended!)
  • You may want to enable the transparent HTTP proxy.
  • and more...

Network Configuration Notes

The default server setup is to connect to the Internet on the first wired ethernet network interface, using IPv4 DHCP. Laptops connect to the server over Access Points (APs) connected to the second wired ethernet network interface or via the wireless mesh using one or more Active Antenna, connected through USB interfaces.

If your XS has 2 network interfaces and you would like to reverse their (WAN, LAN) roles, or if you only have one network interface and would like to swap it's role, you can use the xs-swapnics utility. If you get your WAN via some other interface (e.g., ppp0) then you will want to see the recipes for WAN connections.

IPv6 is not enabled by default and not needed -- to enable external IPv6 you will have to configure the global address of the machine and setup an IPv6 tunnel.

The XS runs a fully-fledged DNS server internally, therefore there is no need to enter the DNS servers from your ISP into the configuration. If you do want the XS to use specific DNSs, see the instructions on using ISP-provided DNS servers

Access Points

XS Usage APNormal.png

Most access points are compatible with the XO. For a list of ones which have been shown to work see Wireless Access Point Compatibility. Unless a single access point is being used (not recommended for more than forty to fifty laptops), a network switch of some sort will also be needed.

Make sure your AP is configured to act as an Access Point, with no added features or smarts. The AP should not be a DHCP server and should not act as a router.

Some tips on configuring APs at XS_Techniques_and_Configuration.

Active Antennae

Important note: Active Antennae is not supported or available from OLPC at this time

If you have active antenna(e) to use, simply plug them in and reboot the XS. It will detect them and allocate them to mshbond0, mshbond1 and mshbond2. It should just work and XOs will see "School server mesh" when they connect to the mesh served by the XS. You may need to manually allocate different frequencies per antenna.

More configuration options

For more information on keeping your XS up to date, Internet content filtering, alternative networking/routing setups, and a lot of other advanced configuration topics see XS_Techniques_and_Configuration.

Upgrading

Upgrade from XS 0.5 or later

With the full ISO:

  • The process is similar to a new (anaconda based) installation. Download the iso, and boot it...
  • In the menu shown right after booting, you choose one of the 'Install or upgrade an existing system'.
  • At the 'Install new or upgrade' screen choose upgrade.
  • Reboot, and complete the 'steps after upgrade'.

With yum:

  • Clean yum's caches
 yum clean all
  • Swith to the new repositories
 rpm -Uvh http://xs-dev.laptop.org/xsrepos/stable/olpc/xs-0.6/i386/xs-release-9-0.4.15.2.ga69303f.noarch.rpm
  • Check that the new repositories have not been installed as "rpmnew":
 ls /etc/yum.repos.d/*rpmnew
  • Run the install!
 yum update 
  • Reboot, and complete the 'steps after upgrade'.

Steps after upgrade:

  • Re-run the /etc/sysconfig/olpc-scripts/domain_config script with the appropriate domain name for the machine.
  • Ensure the right Postgres is set to run
 chkconfig --level 345 postgresql off
 chkconfig --add pgsql-xs

Upgrade from XS 0.4 or earlier

If you are upgrading from XS 0.4 or earlier, the process is similar to a new installation, with some minor changes. In the menu shown right after booting, you should choose one of the 'Install or upgrade an existing system' options, press the Tab key, and add 'upgradeany' to the boot configuration line. After adding that line, press enter twice.

With this extra option, Anaconda will recognise the old installation and will offer to upgrade.

Steps after upgrade:

  • Re-run the /etc/sysconfig/olpc-scripts/domain_config script with the appropriate domain name for the machine.
  • Ensure the right Postgres is set to run
 chkconfig --level 345 postgresql off
 chkconfig --add pgsql-xs

Notes:

  • The new OS may detect your network cards differently -- the roles of WAN and LAN cards may end up swapped from what they were under 0.4. If that happens, use the xs-swapnics script and reboot.

See also