Disassembly B4 wireless antenna: Difference between revisions

From OLPC
Jump to navigation Jump to search
(New page: {{TOCright}} This is a description of how to disassemble the top section of an B4 preproduction XO laptop to replace the wireless antenna (rabbit ears). This is part of the ...)
 
No edit summary
Line 19: Line 19:
<br style="clear:both" />
<br style="clear:both" />
[[image:Antenna2d.JPG|thumb|left|Watch out for this tab!]] [[image:Antenna2e.JPG|thumb|left|Carefully pull out the antenna.]] [[image:Antenna2f.JPG|thumb|left|A removed antenna.]]
[[image:Antenna2d.JPG|thumb|left|Watch out for this tab!]] [[image:Antenna2e.JPG|thumb|left|Carefully pull out the antenna.]] [[image:Antenna2f.JPG|thumb|left|A removed antenna.]]
<br style="clear:both" />

== Removing the back cover / reaching the motherboard ==

=== Step 1 ===
[[image:antenna1a.JPG|thumb|left|Take out 4 screws]] [[image:antenna1b.JPG|thumb|left|Turn over. Pull up and remove the back plate]]
<br style="clear:both" />

== Optional: Removing the "XO Person" on the back cover ==

'''You do not need to remove the "XO Person" on the back cover if you want to get to any other part.'''

=== Step 1 ===
[[image:Xoman1.JPG|thumb|left|Turn the back plate over. Note where the colored plastic fits in.]] [[image:Xoman2.JPG|thumb|left|Use a screwdriver to pop these out]]
<br style="clear:both" />
[[image:Xoman3.JPG|thumb|left|Turn plate over so the XO man faces you. Pull the plastic part out.]] [[image:Xoman4.JPG|thumb|left|Note how the tabs fit in with the back plate.]]

<br style="clear:both" />

== Replacing the "XO Person" on the back cover ==

=== Step 1 ===
[[image:Xoman5.JPG|thumb|left|Fit the new piece in the back plate and snap it back in place.]]
<br style="clear:both" />

== Replacing the back cover ==

=== Step 1 ===
[[image:Antenna3e.JPG|thumb|left|Turn over. Replace the back plate.]] [[image:Antenna3fi.JPG|thumb|left|Pick the right screw!]] [[image:Antenna3fii.JPG|thumb|left|Turn over. Secure the back plate by putting in the four screws where indicated.]]
<br style="clear:both" />
<br style="clear:both" />



Revision as of 05:44, 10 June 2008

This is a description of how to disassemble the top section of an B4 preproduction XO laptop to replace the wireless antenna (rabbit ears). This is part of the Disassembly section of the Troubleshooting Guide and Repair Manual.

This is not needed to replace the wireless antennas on production machines.

Removing the wireless antenna

Step 1

Keep the screen out of the way until the replacement is complete.

Take out 4 screws
Turn over. Pull up and remove the back plate


Take out two screws holding the top bar in place
Watch out for this tab! Pop it out on both sides
Pull the top bar off.


Step 2

Unclip the cable as shown
Peel up the tape.
Remove the two screws.


Watch out for this tab!
Carefully pull out the antenna.
A removed antenna.


Replacing the wireless antenna

Step 1

Carefully put in the new wireless antenna
Pick the right screw!
Screw in the antenna


Step 2

Clip the antenna cable back in.
Replace the top bar. Do not forget the tabs on the sides! Replace the screws to secure the bar.


Turn over. Replace the back plate.
Pick the right screw!
Turn over. Secure the back plate by putting in the four screws where indicated.