Keyboard field repairs: Difference between revisions

From OLPC
Jump to navigation Jump to search
(Catogory)
m (→‎Repair Without Keyboard Removal: Added link to keyboard removal page)
Line 83: Line 83:
[[Image:B8-It Works!.jpg|thumb|center]]
[[Image:B8-It Works!.jpg|thumb|center]]


If the key does not work, you may wish to remove the keyboard according to the dis-assembly instructions, clean off any excess sealer, and follow the instructions above.
If the key does not work, you may wish to [http://wiki.laptop.org/go/Disassembly_bottom#Removing_the_keyboard remove the keyboard] according to the dis-assembly instructions, clean off any excess sealer, and follow the instructions above.


[[Category:Repair]]
[[Category:Repair]]

Revision as of 12:33, 2 August 2010

While OLPC recommends replacing ripped keyboards, that may not always be possible or, may be too costly if several laptops are involved. This simple fix uses a relatively non-toxic silicone sealer that has no harmful fumes. The repair could be, and has been, done safely by children.

Materials

A1-Supplies.jpg


  • Clear Silicone tub and tile sealant (goes on white, dries clear). A 6 oz tube costs less than $3 at most hardware stores and is enough to do dozens of laptops.
  • Toothpicks for applying the sealer
  • Cotton swabs, tissues and water for cleanup
  • Something to protect your table top if doing the repair with the keyboard removed from the laptop (aluminum foil is shown here).

If only a few keys are involved, you may wish to do the repair with the keyboard in place. Follow the second set of directions below to do the repair without removing the keyboard.

If the damage is more extensive, you will probably want to remove the keyboard following these disassembly instructions.

Repair With Keyboard Removal

After removing the keyboard, gently lift off the green silicone keypad, being careful to not tear additional keys. Lay it on your table protector.

Using one toothpick to hold the key in place, gently apply a small amount of silicone to the torn sides of the key with a second toothpick.

A2-Apply Silicone.jpg


Use a damp (not soaking wet) cotton swab to remove the excess silicone sealer.

A3-Remove Excess.jpg


More cleanup may be needed.

A4-Needs More Cleanup.jpg


Use a damp tissue for a final touchup. In this photo, the F, G, and H keys and the right half of the space bar were repaired previously and have already dried.

A5-Touch Up With Tissue.jpg


Allow the silicone to dry overnight before re-assembling the laptop according to the directions on the wiki.

Repair Without Keyboard Removal

While this may seem easier than removing the keyboard, you must work very carefully to not allow silicone to get under the green silicone keypad.

A key that had been completely torn off was re-fitted in this repair.

B1-"R" Key ripped completely off.jpg


Carefully fit the key back into its place in the keyboard.

B2-Put key back in place.jpg

Apply silicone to one edge of the key and carefully clean it. If you try to do the entire key at once, it will be difficult to keep it in place while working.

B3-Apply silcone to one side.jpg

Allow the first side to dry overnight.

B4-Wait for first side to dry.jpg

Holding the key in place with one toothpick, carefully apply silicone to the remaining three sides, being careful not to get it under the key.

B5-Apply Silicone To Other 3 Sides.jpg

Clean up with a toothpick. To avoid having sealer run under the key, it is probably best not to use the wet cotton swab or wet tissue here.

B6-Clean With Toothpick.jpg

Let they keyboard dry overnight. Note the repair isn't as clean as the one with the keyboard removed. That is because we did not use the water in the cleanup.

B7-Silicone Has Dried.jpg

Test the results. This one worked.

B8-It Works!.jpg

If the key does not work, you may wish to remove the keyboard according to the dis-assembly instructions, clean off any excess sealer, and follow the instructions above.