XS Community Edition/0.3/Configuring

Initial Setup

1. Use "ifconfig" to determine the ip address of the XS.
   Take note of its eth0-ip-address = WAN-ip.
   If you've inserted the USB Ethernet Adapter above (serving the LAN/Intranet) also take note of the school server's eth1-ip-address = LAN-ip = 172.18.96.1
2. If you inserted the USB Ethernet Adapter above, configure its own Wifi Access Point (AP) to properly serve other LAN/Intranet client XOs. (If the Wifi AP is a router, DO NOT plug into its "WAN" port -- instead use any of its LAN/normal ports. And be sure to enable the AP's "bridge mode" or similar, or specifically disable the AP's own DHCP)

Content Filtering with OpenDNS

There are two components to settting up content filtering with OpenDNS. First, the XSCE needs to look at OpenDNS's DNS IP addresses for DNS. Then there must be an OpenDNS account associated with the XSCE's public IP address. Simply specifying the OpenDNS servers as the XSCE's DNS servers doesn't filter any content. You need to set up an account and configure the content filter level so that OpenDNS knows what to block for your specific IP address.

You may wish to use the OpenDNS DNS servers instead of your ISPs DNS servers if your ISP's DNS servers are unreliable. If you don't need content filtering, no account is required.

To point the XSCE to the OpenDNS DNS servers, edit /etc/named-xs.conf.in for the forwarders line:

options
{
        /* make named use port 53 for the source of all queries, to allow
         * firewalls to block all ports except 53:
         */
        forwarders {208.67.222.222; 208.67.220.220;};

Run this command to write the change to named-xs.conf.in to named-xs.conf:
xs-domain-config

Restart the named service:
systemctl restart named.service

Now the XSCE is pointing to OpenDNS's DNS servers. However, internet content will not be filtered until you set up an account with OpenDNS and configure your filter level.

From the IP you wish to enable content filtering for, go to http://www.opendns.com and create an account. When setting a label (friendly name) for your network, it's best to avoid special characters and spaces.

Once your OpenDNS account is created and your network is listed in the settings tab, click on the network's IP to manage settings. Under "Web Content Filtering," select your desired content filter level and click Apply.

If you have a static IP, setup is complete. If your IP is dynamic, the ddclient service is necessary to update OpenDNS when your IP changes.

The ddclient service requires three pieces of information about your OpenDNS account: username, password, and network label. The network label can be found under the OpenDNS Dashboard, in the settings tab, listed in the "LABEL" column under "Your networks."

To install ddclient:
yum -y install ddclient

At the bottom of /etc/ddclient.conf, append the following lines:

##
## OpenDNS.com account-configuration
##
use=web, web=myip.dnsomatic.com
ssl=yes
server=updates.opendns.com
protocol=dyndns2
login=yourlogin
password=yourpassword
your-network-name

Remember how you needed three pieces of information about your OpenDNS account? Edit these three lines with your OpenDNS login credentials and your OpenDNS network label:

login=yourlogin
password=yourpassword
your-network-name

Enable the ddclient service, for all future boots:
systemctl enable ddclient.service

Start the ddclient service, during the current boot:
systemctl start ddclient.service

If ddclient fails to start with the above command, reboot the XSCE and verify that ddclient came up at boot:
systemctl status ddclient.service

The default ddclient update interval is 300 seconds, which you can change in /etc/ddclient.conf.