Getting started/connecting: Difference between revisions

From OLPC
Jump to navigation Jump to search
(..)
 
(draft)
Line 3: Line 3:
:Source : http://laptop.org/en/laptop/start/connecting.shtml
:Source : http://laptop.org/en/laptop/start/connecting.shtml
:Full Getting-started PDF : http://laptop.org/en/laptop/start/getting_started_3.pdf
:Full Getting-started PDF : http://laptop.org/en/laptop/start/getting_started_3.pdf

== Side panel ==

mesh view
:You connect to the Internet from the Neighborhood view.

ap
:Access points are represented by circles. The fill level indicates signal strength.

locked ap
:Access points that require keys have a “locked” badge.

ap hover
:The name of the access point is displayed when you hover over it.

connecting
:You connect by “clicking” in the center of the circle. The center of the circle will blink while the laptop is trying to connect.

connected ap
:Once you are connected, the rim of the circle turns white. (If the attempt to connect fails, the circle will stop blinking, but the rim will not turn white. Try again—it sometimes takes 2–3 tries to connect.)

enter a key
:You will be prompted if the access point requires a key.

For more information about connecting, please see the Support page in our wiki.

== Main panel ==

Connecting

There are three ways to connect to the Internet:
• wireless access point (WiFi hotspot);
• “School Server” mesh network; or
• “simple” mesh network, which lets you collaborate directly with other XOs.

You make your connection from the Neighborhood view. Your current connection status is shown on the Home view. (The XO was designed for wireless access because in the developing world, wireless is actually the fastest, most reliable, and least expensive way to connect.)



Step 1: Go to the Neighborhood view

connecting, Step 1

neighborhood
:Go to the Neighborhood view to connect to an access point. The Neighborhood view is accessed by pressing the round key with eight dots, found in the upper-left corner of the keyboard.



Step 2: Choose an access point

connecting, Step 2

Networks (access points) are represented by circles on the Neighborhood view. Networks can be identified by hovering over the circles: an access point is identified by its name (ESSID); a mesh-portal point is identified by its channel number (1, 6, or 11). You can also search for an access point by name in the search bar at the top of the page.

Signal strength is indicated by the fill-level of the circle. The color of the circle is based upon the name of the access point. Networks that are locked are identified by a badge.



Step 3: Activate a connection

To activate your network connection, click once inside the circle that corresponds to your chosen access point. (To “click”, press once on the left-hand touchpad button—the button with the × symbol at the front of the touchpad.) While the XO is trying to establish the connection, the inside of the circle will blink. Once the connection is established, the outside of the circle will turn white. If for some reason the connection failed, the circle will stop blinking. Sometimes it is necessary to try several times before the connection is established

If the access point requires a key, you will be prompted. Note that different types of access points require different types of keys: be sure to select the correct type from the pull-down menu that is presented. Some access points (such as the Apple Extreme®) will only work with a hexadecimal value. If you have a password or passphrase, go to Hex Converter to get the hex key. Also, with the Apple Extreme you need to set “shared key”. Most other access points prefer the “open key” setting when using WEP.

Currently, we do not support WPA-enabled WiFi access points; we anticipate including WPA support in early 2008.



Step 4: Checking the connection

connecting, Step 4

home
:Go to the Home View—by using the key with one circle found in the upper-left corner of the keyboard—to check your connection. By hovering over the circle icon, you will find details about your connection status.

If you don't specify a network, the XO will attempt to join a simple mesh network, enabling you to collaborate with other XOs, but not access the Internet.

For more information about connecting, please see the Support page in our wiki.

Revision as of 03:31, 17 February 2008

   Español HowTo [ID# 109751]  +/-  


Source : http://laptop.org/en/laptop/start/connecting.shtml
Full Getting-started PDF : http://laptop.org/en/laptop/start/getting_started_3.pdf

Side panel

mesh view

You connect to the Internet from the Neighborhood view.

ap

Access points are represented by circles. The fill level indicates signal strength.

locked ap

Access points that require keys have a “locked” badge.

ap hover

The name of the access point is displayed when you hover over it.

connecting

You connect by “clicking” in the center of the circle. The center of the circle will blink while the laptop is trying to connect.

connected ap

Once you are connected, the rim of the circle turns white. (If the attempt to connect fails, the circle will stop blinking, but the rim will not turn white. Try again—it sometimes takes 2–3 tries to connect.)

enter a key

You will be prompted if the access point requires a key.

For more information about connecting, please see the Support page in our wiki.

Main panel

Connecting

There are three ways to connect to the Internet:

• wireless access point (WiFi hotspot);
• “School Server” mesh network; or
• “simple” mesh network, which lets you collaborate directly with other XOs.

You make your connection from the Neighborhood view. Your current connection status is shown on the Home view. (The XO was designed for wireless access because in the developing world, wireless is actually the fastest, most reliable, and least expensive way to connect.)


Step 1: Go to the Neighborhood view

connecting, Step 1

neighborhood

Go to the Neighborhood view to connect to an access point. The Neighborhood view is accessed by pressing the round key with eight dots, found in the upper-left corner of the keyboard.


Step 2: Choose an access point

connecting, Step 2

Networks (access points) are represented by circles on the Neighborhood view. Networks can be identified by hovering over the circles: an access point is identified by its name (ESSID); a mesh-portal point is identified by its channel number (1, 6, or 11). You can also search for an access point by name in the search bar at the top of the page.

Signal strength is indicated by the fill-level of the circle. The color of the circle is based upon the name of the access point. Networks that are locked are identified by a badge.


Step 3: Activate a connection

To activate your network connection, click once inside the circle that corresponds to your chosen access point. (To “click”, press once on the left-hand touchpad button—the button with the × symbol at the front of the touchpad.) While the XO is trying to establish the connection, the inside of the circle will blink. Once the connection is established, the outside of the circle will turn white. If for some reason the connection failed, the circle will stop blinking. Sometimes it is necessary to try several times before the connection is established

If the access point requires a key, you will be prompted. Note that different types of access points require different types of keys: be sure to select the correct type from the pull-down menu that is presented. Some access points (such as the Apple Extreme®) will only work with a hexadecimal value. If you have a password or passphrase, go to Hex Converter to get the hex key. Also, with the Apple Extreme you need to set “shared key”. Most other access points prefer the “open key” setting when using WEP.

Currently, we do not support WPA-enabled WiFi access points; we anticipate including WPA support in early 2008.


Step 4: Checking the connection

connecting, Step 4

home

Go to the Home View—by using the key with one circle found in the upper-left corner of the keyboard—to check your connection. By hovering over the circle icon, you will find details about your connection status.

If you don't specify a network, the XO will attempt to join a simple mesh network, enabling you to collaborate with other XOs, but not access the Internet.

For more information about connecting, please see the Support page in our wiki.