XO1.75 B1 C1 Changes: Difference between revisions

From OLPC
Jump to navigation Jump to search
No edit summary
Line 8: Line 8:


The LV_SET signal should change to a EC PWM output (PWM2, pin 26), allowing a greater voltage swing than the EC DAC output. The OLS_CATHODE signal moves to GPIO30 (pin 54) as a result.
The LV_SET signal should change to a EC PWM output (PWM2, pin 26), allowing a greater voltage swing than the EC DAC output. The OLS_CATHODE signal moves to GPIO30 (pin 54) as a result.

==Fix RTC Power==
It turns out that the IDT1338 is woefully underspec'ed, and needs a power-down time of 2 mS across all production parts to properly preserve the time, not the 300 uS reported by the data sheet. The vendor is looking into this, but a switch will be added in the power line of the IDT1338 to cheaply provide a nice, slow power-down.


==Modify Vcore supply==
==Modify Vcore supply==
Line 16: Line 19:


This was instead fixed by adding a capacitor and resistor (R384/C377, R385/C378) to the control signals, increasing the turn-on and turn-off times.
This was instead fixed by adding a capacitor and resistor (R384/C377, R385/C378) to the control signals, increasing the turn-on and turn-off times.

Additional bulk bypassing (3 x 2.2uF) was added around the eMMC device.


==Pullups on Accelerometer==
==Pullups on Accelerometer==
Line 45: Line 50:


New circuitry needs to be added around Q14.
New circuitry needs to be added around Q14.

==ADET protection==
The voltage on the ADET input to the battery charger may be excessive in B1 units. This will not be fatal, but is not recommended by the manufacturer. The ADET input will have its own
voltage divider, w. a zener to prevent overvoltage of the charger.


=C1 Layout Fixes=
=C1 Layout Fixes=

Revision as of 17:16, 6 September 2011

  This page is monitored by the OLPC team.

These are the changes planned for the XO-1.75 C1 prototype, from the B1 prototypes.

C1 Electrical Fixes

Improved MPPT

The circuit generating the PWR_LIMIT_ON needs to be modified to only assert the signal if power limiting is turned on. On B1, it is asserted whenever the laptop is accepting power from the DC input (power limited or not). [Remove PR227, change PR244 to 4.7K, remove PR229 and populate w. a 0.1 uF)

The LV_SET signal should change to a EC PWM output (PWM2, pin 26), allowing a greater voltage swing than the EC DAC output. The OLS_CATHODE signal moves to GPIO30 (pin 54) as a result.

Fix RTC Power

It turns out that the IDT1338 is woefully underspec'ed, and needs a power-down time of 2 mS across all production parts to properly preserve the time, not the 300 uS reported by the data sheet. The vendor is looking into this, but a switch will be added in the power line of the IDT1338 to cheaply provide a nice, slow power-down.

Modify Vcore supply

The Vcore suply voltages should be 1.345V nominal and 1.25V nominal, instead of 1.40V and 1.345V as it is now.

Increase bulk bypassing

Add another 22 uF of capacitor to the +3.3V rail (populate PC54).

This was instead fixed by adding a capacitor and resistor (R384/C377, R385/C378) to the control signals, increasing the turn-on and turn-off times.

Additional bulk bypassing (3 x 2.2uF) was added around the eMMC device.

Pullups on Accelerometer

Both <trac>11041</trac> or <trac>10882</trac> are caused by a lack of external pullups on the I2C bus. 1.3K pullups to should be added between G_SENSOR_SDA/G_SENSOR_SCL and +1.8V_GPIO. VDD_IO on the Accelerometer (U15) should be tied to +1.8V_GPIO, not +1.8V. Same with U5.

Memory Size Select

The XO-1.75 uses GPI0s 1 and 0 to indicate the amount of memory present on the motherboard.

Memory Size
0 512 MB
1 1 GB
2 2 GB
3 undefined

Move OLS

The OLS diode should be moved to be located next to LED4, and blanking circuitry added to control it.

The existing blanking circuitry (D19 and R379) should be removed.

New circuitry needs to be added around Q14.

ADET protection

The voltage on the ADET input to the battery charger may be excessive in B1 units. This will not be fatal, but is not recommended by the manufacturer. The ADET input will have its own voltage divider, w. a zener to prevent overvoltage of the charger.

C1 Layout Fixes

Internal SD Select

With the replacement of the full-size internal SD slot with a latching microSD slot, there is no longer a card detect signal generated to automatically switch the boot device.

We need to increase the size of R341/R341 to 0603 or 0805, and label them somehow.

Move OLS

The OLS diode (LED14) should be next to LED4, not LED5. Clearance with the mainframe and lightpipe aperture needs to be checked.

Planned Feature Changes