Talk:Acoustic Tape Measure

Some ideas

Measure velocity using doppler?

For something like the "dance revolution graph" activity - maybe you could take some shortcuts.

idea 1: Have one computer broadcast an intermittent square wave at a given frequency. I understand that the result would lack some high harmonics necessary for a true square wave - but I bet it would be good enough to make the calculation of when the thing starts pretty simple. Certainly less robust than full-spectrum white noise, but probably good enough after an initial calibration against white noise.

idea 2: Have one computer broadcast a continuous square wave, and the other one just count beats (using some reasonable assumptions about possible accelerations to throw away bad data). This would tend to get progressively out-of-sync, but it would be fully real-time. Maybe have an intermittent transient to resync...

What you're describing sounds a lot like a Phase-Locked Loop. Something like that might indeed be able to measure velocity. Why do we want to measure velocity of laptops? Sounds like a great way to trip and break your most valuable possession. Ben 18:29, 15 October 2007 (EDT)

The point is, doing a whole deconvolve or whatever to match a known sound is computationally much heavier than just binning against a known frequency - sine or square, either way it's even easier than an FFT.

I actually imagine that maybe you could find some good algorithms in use in GPS recievers for electromagnetic stuff - the problem is similar.

(I know - everyone can kibbutz, few will code.)

--Homunq 16:46, 5 October 2007 (EDT)

ps. speed of sound depends on altitude as well as temperature. I think that asking people to guess the temperature is more accurate AND educational than just guessing it using time/location.

That was my first thought as well, but it is wrong. Except to the extent that air is not an ideal gas, the speed of sound does not depend on altitude. We often say that it does, but that's mostly because high-altitude air is cold. Humidity has a bigger effect, but you can ignore that too. Temperature is what matters. See wikipedia for the numbers and math. AlbertCahalan 22:40, 6 October 2007 (EDT)

OK, my bad. But about my other points:

1. I was thinking further about ideal waveforms - you want something with well-understood shortcut algorithms to recognize it in spite of noise, and the algorithms should be very specific in the time domain. FFT and friends are good algorithms, but they are particularly bad at time distinctions. It's been ages since I "studied" this stuff (and I never understood it any better than I had to to make my HS math teacher believe I was doing my independent study), but, have you thought about wavelets?

He's using phase angle of a non-repeating noise AFAIK, so I think things are fine in that respect. Audio chips with different speed clocks would get him, as would any motion. AlbertCahalan 12:41, 13 October 2007 (EDT)

2. I still think that a human guess at temperature - that is, if you don't have a dongle for use with the "measure" activity - is the best, and most educational, answer. Using the stereo speakers, aren't you going to have problems because of the speed of sound in the laptop plastic? (problems that are avoided if the laptops are more-or-less facing each other head-on). Homunq 08:01, 13 October 2007 (EDT)

As long as the speed of sound in the plastic is significantly different from the speed of sound in air, the sound arriving through the plastic can be ignored. (take the first peak or second peak, whichever one is the air) AlbertCahalan 12:41, 13 October 2007 (EDT)

I find this idea intriguing. Maybe there should be some option to input air temperature and relative humidity, possibly hidden in an "Advanced Settings" tab. I've been trying to figure out how to provide the simplest possible interface, but that might not be a bad compromise. It might also provide an educational benefit: punch in the air temperature and humidity, and it tells you the speed of sound. Ben 18:29, 15 October 2007 (EDT)

More ideas

You have 2 speakers. That can pretty much let you determine angle, given a few minor assumptions about a flat world and similar. Maybe you place the laptops on hyperbolas.

With two laptops, it's not clear that we can really talk about placing the laptops on hyperbolas. However, it is true that, in principle, one could determine the angle at which they face each other. The measurement would not be terribly accurate, and it would at least double the amount of time required for a measurement. It might be possible, but I haven't seen a reason to do it. Ben 18:12, 15 October 2007 (EDT)

The speakers are a known distance from each other. With stereo, you can get the speaker-to-speaker distance. (they share the same start-up lag) From the error, compute temperature. AlbertCahalan 04:31, 6 October 2007 (EDT)

This might be possible. The first problem is acoustics: because the speaker and microphone are both somewhat directional, an appropriately placed object might provide a stronger path than the direct path through the air over the screen. Additionally, to achieve even 5 degree C accuracy, the distance must be known and measured to better than 1% accuracy. The speakers are less than 20 cm apart, so we are talking about 2 mm of position accuracy. Even if the speaker placement is that precise, 48 KHz samples are spaced 7.5 mm apart in air. Thus, an extremely accurate sub-sample positioning measurement algorithm is required. This may also be possible (and I am looking into it) but it is edging into the realm of algorithms research. To get 1 degree C requires sub-mm speaker placement and 20x superresolution in the positioning. Ben 18:12, 15 October 2007 (EDT)

Never mind 1 degree C. The air temperature range is something like -15 to 65. A mid-range hard-coded temperature could be wrong by 40 degrees C. 24.110.145.202 00:12, 16 October 2007 (EDT)

Pick the lowest measurement that is a definite peak and not in the range of measurements that are known to be plastic. In case the path is not a simple line, a correction factor may be desirable. 24.110.145.202 00:12, 16 October 2007 (EDT)