Peripherals/Touch Screen
Technology
Different touch screen technologies:
- 4-Wire Resistive
- 5-Wire Resistive
- Capacitive
- Surface Acoustic Wave
- Infrared
- Strain Gauge technology
- embedded ccd in panel - can't find link but light detectors can be intermixed with light generators, maybe on an oled display, so the computer can detect when light reflected
- A simple light sensor could also work as a display pointer. A tethered pen could detect flashed target boxes, like the old Nintendo Light Gun. For continuous drawing, the screen could flash through a series of patterns where the pen either sees light or dark. Each screen location would thus have a unique binary code flash through it, which would be reported by the pen's narrow light sensor. This screen scan will start in a small box near where the pen was last to reduce search time, and the eyesore of flickering. -- Nintendo wii remote has been hacked to provide multi touch interface-- http://gizmodo.com/gadgets/clips/wiimote-hack-is-wireless-multitouch-tv-321329.php
Apparently most PDA’s use 4-Wire Resistive touch screen technology. However I am not positive on this.
Adding a Touch Screen to the XO
The XO has a 7,5 inches display, so is quite hard to find. An alternative is buy a 8 inches, touch screen(no wide). I have bought mine at http://www.iiic.hk.cn/ Then you have to open the XO computer and remove the screws in the lcd corners, then remove the rubber over them to obtain more space between the top plastic and the display. The touch screen comes with an usb controller, that we soldier inside the XO USB port as you can see in the pothograph. We could obtain some free space, over the display as you can see in the photograph.
Soldering the USB controller
All the components
Touch screen over the display
How to do
This are the steps that you must do to have your touch screen working.
Get starting
First of all you have to make a root in a jail, in order to install gcc and Make utils and compile the necesary sources linking with the correct kernel version of the XO.
Compiling the kernel module of the Touch Kit
into the root in the jail we need to compile the device driver tkusb.ko linking with the correct kernel, so you have to download the correct kernel soruces that match with you XO kernel version. In this case the kernel version of my XO is 2.6.25, to know wich kernel version you have run uname -r in a terminal. The following script will download the kernel sources 2.6.25 and install it.
bash-3.2# wget http://dev.laptop.org/~dilinger/testing/kernel-2.6.25-20080925.1.olpc.f10b654367d7065.src.rpm
bash-3.2# mkdir /usr/src/redhat
bash-3.2# mkdir /usr/src/redhat/SOURCES
bash-3.2# rpm -ivh kernel-2.6.25-20080925.1.olpc.f10b654367d7065.src.rpm
bash-3.2# yum install redhat-rpm-config
bash-3.2# yum install m4
bash-3.2# yum install rpm-build
bash-3.2# yum install unifdef
bash-3.2# yum install tar
bash-3.2# rpmbuild -ba --define "dist olpc1" --define "olpc 1" --define "head dc5079fafb767e4" --target=i586 /usr/src/redhat/SPECS/olpc-2.6.spec
Download the touch screen drivers from http://www.touchkit.com/drivers/linux/TouchKit-2.03.1712-32b-k26-x14.tar.gz In the Makefile of the touch usb chanhe KDIR for KDIR := /usr/src/redhat/BUILD/kernel-2.6.25/linux-2.6.25.i586/ (or the correct) If make returns an error, you could solve it by adding {} at the end of the table usb_device_id tk_table[] defined in the file tkusb.c, view http://forum.eeeuser.com/viewtopic.php?pid=175102 Now you could run make!
Installing the driver
bash-3.2# cp tkusb.ko /lib/modules/
bash-3.2# mknod /dev/tkpanel0 c 180 180
Add the following to /etc/rc.local
Code:
## TouchKit kernel module section begin ##
rmmod touchkitusb
## This module may be renamed “usbtouchscreen” ##
insmod /lib/modules/tkusb.ko
## for Kernel 2.6.x only.<br />
## TouchKit kernel module section end ##
The Xorg
You need to modify the xorg.conf to view the touch screen as a human interface device (HID). Add this to the /etc/xorg.conf:
Section "InputDevice"
Identifier "EETI"
Driver "egalax"
Option "Device" "/dev/tkpanel0"
Option "Parameters" "/var/lib/eeti.param"
Option "ScreenNo" "0"
EndSection
then you have to copy the file egalax_drv.so to the directory /usr/lib/xorg/modules/input/