XO 3 Battery
This page contains a discussion of the battery technology for use in the XO-3 tablet.
Introduction
Batteries consist of single battery cells which are placed in series (to increase the voltage available from the battery) and/or in parallel (to increase the current available from the battery). There are advantages and disadvantages to both approaches --- which should be used in XO-3 ?
The power distribution network in the XO-3 will have the battery directly connected to the main power distribution bus:
This avoids the inefficiency of converting the battery voltage to the main distribution voltage, but requires that the voltage converters accept the full range of battery voltage.
For LiIon, a single cell ranges from 3.2 to 4.2V (6.4 to 8.4V if 2S1P). For LiFePo4 (used in the XO), a single cell ranges from 2.75 to 3.4V (5.5 to 6.8V if 2S1P).
Series Connection
In this case, two or more battery cells are placed in series to increase the voltage provided by the battery.
- Increases the main system supply voltage, reducing the main supply current and associated losses
- Better match to higher voltage (lower current) external power supplies
Battery Cell Balancing
If battery cells are connected in series, differences in cell voltages will cause some cells to receive more power than others when charging. Over a number of charge cycles, this will lead to a charge imbalance between the cells in the battery. This is prevented by matching the voltages of the battery cells used in a battery.
Parallel Connection
In this case, two or more battery cells are placed in parallel, increasing the total current (capacity) of the battery while keeping the battery voltage equivalent to the cell voltage.
- Avoids cell balancing problems
- Allows a lower system voltage, simplifying charging from a low voltage (USB, or 5V) charger
- Introduces complications in that some power supplies (+3.3V) have to operate from a supply that ranges above and below (2.75V - 3.4V) the desired output.
Nomenclature
Batteries (or battery packs) are referred to by the configuration of the cells internally, using a mSnP naming scheme --- m sets in series of n cells in parallel. Thus a battery which consists of two battery cells in series, none in parallel (such as used in the XO-1) is a 2S1P battery. Actually, the XO-1 battery was designed to be a 2S2P battery, but two oval cells were used in series instead of four cylindrical cells (two sets in series of two cells in parallel) for cost reduction. A typical tablet battery (1S1P or 1S2P) has one or two battery cells in parallel, none in series.
Battery Configuration
Unfortunately, the reality of battery packs introduces factors which make 1SmP battery configuration less power eficient. The battery charging circuit on the motherboard includes a MOSFET for disabling battery charging (Q1) and a resistor for measuring the battery charge current (R1). For safety reasons, all Lithium based battery packs include a safety circuit which disconnects the battery in cases of overcurrent, overvoltage or overtemperature. This introduces another resistor (R2), and two MOSFETs (Q2/Q3) in series with the battery circuit.
Typical minimum values for these components would be 0.010 ohms for R1 and R2, and 0.030 ohms (drain-source resistance) for Q1, Q2, and Q3, giving a minimum resistance of 0.110 ohms in series with the battery cells. If drawing 3W from a 3V battery, 110 mW will be wasted in this circuit. If, however, a 2S1P configuration is used, drawing 3W from the 6V battery only wastes 27 mW.
Countering this, however, are changes in the voltage converter efficiencies due to the different main voltage.
To be continued
Battery Technology
OLPC is constantly looking for new battery technologies which:
- allow operation and charging over an extended temperature range (0 to 50C)
- are lightweight
- are relatively safe (non-explosive)
The current candidate is Lithium Iron Phosphate (LiFePO4). Slight improvements in energy density are available from a hybrid technology, where additional metals other than Iron are used.