Disassembly top

From OLPC
Revision as of 04:00, 10 June 2008 by Wad (talk | contribs)
Jump to navigation Jump to search

This is a description of how to disassemble the top portion of an XO laptop. This is part of the Disassembly section of the Troubleshooting Guide and Repair Manual.

XO before disassembly

As a precaution, remember to remove the battery.

Before we begin
Remove the battery.


Removing the front panel

Step 1

Open the laptop and flip the screen up. Rotate it a 90 degree angle as shown in the sequence below. Next, remove the screws from the bottom of the screen - there are two on each side (right/left) of the XO, so make sure to get all four.

Flip screen up
Rotate
Unscrew - remember, there are 4.


Step 2

Remove the two green panels from the side of the XO. Slide them upwards and lift them off as shown.

Screen 2a.jpg
Slide up
Lift off


Step 3

Finally, pull off the front panel. It is tabbed, so it can simply be pulled out. Pull the bottom out (where the screws came out), and gently slide the piece downwards and out.

Screen 3a.jpg
Screen 3b.jpg


Removing the screen

Step 1

To get the screen out, remove the four screws highlighted.

Unscrew


Step 2

Next, carefully slide the screen out, pulling the bottom out. Do not tug it or let go, as it will still be connected to the motherboard by two cables.

Slide out gently
Screen 4c.jpg
Watch out for cables!


The connectors have a black plastic bar holding the cable down. To unclamp the cable you have to lift that bar by tugging on the little tab away from the circuit board.

Unhook the cable
Watch out for this little cable, too.
Good to go!


Optional: Removing the wireless antenna

You do not need to remove the wireless antenna if you are trying to get to any other part.

Step 1

Keep the screen out of the way until the replacement is complete.

Take out 4 screws
Turn over. Pull up and remove the back plate


Take out two screws holding the top bar in place
Watch out for this tab! Pop it out on both sides
Pull the top bar off.


Step 2

Unclip the cable as shown
Peel up the tape.
Remove the two screws.


Watch out for this tab!
Carefully pull out the antenna.
A removed antenna.


Removing the back cover / reaching the motherboard

Step 1

Take out 4 screws
Turn over. Pull up and remove the back plate


Optional: Removing the "XO Person" on the back cover

You do not need to remove the "XO Person" on the back cover if you want to get to any other part.

Step 1

Turn the back plate over. Note where the colored plastic fits in.
Use a screwdriver to pop these out


Turn plate over so the XO man faces you. Pull the plastic part out.
Note how the tabs fit in with the back plate.


Replacing the "XO Person" on the back cover

Step 1

Fit the new piece in the back plate and snap it back in place.


Replacing the back cover

Step 1

Turn over. Replace the back plate.
Pick the right screw!
Turn over. Secure the back plate by putting in the four screws where indicated.


Replacing the wireless antenna

Step 1

Carefully put in the new wireless antenna
Pick the right screw!
Screw in the antenna


Step 2

Clip the antenna cable back in.
Replace the top bar. Do not forget the tabs on the sides! Replace the screws to secure the bar.


Turn over. Replace the back plate.
Pick the right screw!
Turn over. Secure the back plate by putting in the four screws where indicated.



Replacing the backlight

Replace the backlight by attaching the new backlight to the display. Ensure the backlight connection cable is attached and lying flat along the display.

Gently put the new backlight in place
Reattach tape to the center of the backlight


Place the two screws back in
Reattach the tape on the small cables


Replacing the screen

Step 1

Reattach the screen by sliding the connection cables into place and clipping them back down (it is generally easier to clip the thinner one that has a longer tether first). Reseat the screen, making sure that it sits flat and that none of the spacers are gone.

Error creating thumbnail: File missing
Clip little cable in
Clip big cable in


Gently slide screen back in
The screws with the large heads (4) go back in


Replacing the front panel

Step 1

Slide the front panel back on, making sure that it sits flat. Note that there are hooks on the side of the panel (highlighted in blue) that need to slide into place; pushing the top of the screen flat and sliding it upwards works well.

Watch out for these hooks
The rest of the panel slides into place


Step 2

Slide the green side pieces back into place. Then, rotate the XO 90 degrees and put the remaining screws back. Don't forget that the screws go in on both sides (right/left).

Screen 7a.jpg
Side panels slide back in place
Almost there!


Rotate
Put screws (4) back in.