OLPC Firmware q2f15

From OLPC
Revision as of 05:14, 14 February 2013 by Quozl (talk | contribs)
Jump to navigation Jump to search


Pencil.png NOTE: The contents of this page are not set in stone, and are subject to change!

This page is a draft in active flux ...
Please leave suggestions on the talk page.

Pencil.png
  This page is monitored by the OLPC team.

OLPC Firmware Release q2f15

Works on XO-1 systems.


Download q2f15.rom
Build date time 2013-02-14 00:03:22
Source revision 3555.
EC version 1.2.1
Wireless firmware version 5.110.22.p23

Changes

  • 3555 OLPC - startup sound. Avoid searching jffs2 filesystem on XO-1 because mounting it takes a long time. Avoid checking for file existence; just try and if we fail, fallback to the built-in sound. Avoids one microSD or eMMC power cycle from boot on XO-1.5, XO-1.75, and XO-4 when the startup sound is present.
  • 3554 OLPC XO-1 - suppress DCON switching during display test, to fix regression due to earlier reorganisation
  • 3545 OLPC - move some common developer utilities into a single file.
  • 3542 OLPC - telnetd, allow subsequent reconnections, display IP address of client, suppress 300ms options negotiation allowing to occur during normal mux I/O, also fixes <trac>12539</trac>.
  • 3540 mkdropin - fix calculation of ending address for reserved area skip, occasionally a reserved area began with trailing bytes of the dropin header.
  • 3536 USB - add an interrupt lockout for the keyboard alarm handler, so that it is skipped if the non-interrupt context is in the middle of a bulk or interrupt pipe method. A fix for OLPC <trac>12516</trac>. Actual cause still unknown.
  • 3533 OLPC - allocate any heap during driver open rather than during an alarm handler, for the /ap-sp, /keyboard, and /usb/keyboard drivers, fixes <trac>12466</trac>, tested with 128,000 boot cycles across four units.
  • 3518 telnetd - use the I/O multiplexor, so that the telnet client becomes a mirror of the keyboard, display, and serial console.
  • 3517 usbserial - start the read again next time the device is opened, fixes re-use of USB serial devices by applications, without this change the read path yields no data on subsequent open because the bulk in is not set up.
  • 3503 .caller - minor stack comment fix, no execution effect
  • 3494 OLPC <trac>12392</trac> - Fixed hardcoded offset for security tag in manufacturing data. enable-security was failing on XO-4 due to the change in SPI FLASH size.
  • 3491 Ping utility - clean up properly (close network driver) if set-host aborts due to an unresolvable hostname.
  • 3471 usbserial - FTDI232 driver for OLPC serial adapters
  • 3470 Start of a driver for FTDI serial chips. Needs fleshing out.
  • 3466 OLPC: Fix battery temperature calculation error


Which Firmware Do You Have?

The best method for finding out what firmware version you have on a laptop depends on whether the laptop is secured or not, and what operating state it is in.

Unsecured Laptop

Obtain the Ok prompt, the firmware version is displayed in the startup banner, thus: 

 OLPC ..., ... memory installed, ..., S/N SHF7250024D
 OpenFirmware  q2f14 ...   EC Firmware Ver:...
               ^^^^^

You can also obtain the built date: 

 ok .built

This is the date and time that this image of the firmware was built by the release engineer.

Secured Laptop

Power up the laptop with the ✓ (check mark) game button held down. You will be asked to Release the game keys to continue. Release the ✓ (check mark) game button and watch carefully. For a short time the startup banner will be displayed, like this: 

 OLPC ..., ... memory installed, ..., S/N SHF7250024D
 OpenFirmware  q2f14 ...   EC Firmware Ver:...
               ^^^^^

Alternatively, if the laptop is already booted, go to the Sugar home view, click on the icon at the centre of the screen and select "My Settings" then "About my Computer." The firmware version is displayed there.

Alternatively, in the Terminal activity or a text console, type: 

 cat /proc/device-tree/openprom/model

or 

 cat /ofw/openprom/model

With certain older firmware versions, if the operating system will not start, and the laptop is secured, you will not be able to obtain the firmware version using the above methods, so our recommendation is to go ahead and upgrade anyway. The procedure is safe and will not do anything if you already have up-to-date firmware.


Installation

When installing new firmware, you must have a well-charged battery and the AC adapter plugged in. The firmware update code will not proceed otherwise. Possible error messages are:

error message how to fix
AC not present plug in the power cord, check the battery LED is on, then try again.
No external power plug in the power cord, check the battery LED is on, then try again,
No battery plug in the battery, check the latches, then try again, or try another battery,
Battery low allow more time for the battery to charge, then try again, or try another battery.

Unsecured Laptop

This section is for unsecured laptops. Most XO-1.5 and XO-1.75 laptops are unsecured. Most developer XO laptops are unsecured. To unsecure your laptop, follow the instructions at Activation and Developer Keys.

You may install using either:

  • a USB drive or SD card,
  • the laptop's internal drive,
  • a network.

Choose one.

Using a USB drive or SD card

  • check the battery is inserted and locked,
  • check that the power cord is in place and the battery indicator is green,
  • insert the USB drive or SD card,
  • turn on the laptop, and get to the 'ok' prompt. See Ok for more detail. You should see:
ok
  • if the downloaded file is on a USB drive, type:
 flash u:\q2f14.rom
  • if the downloaded file is on an external SD card:
 flash sd:\boot\q2f14.rom
  • wait for the laptop to reboot itself,
  • remove the USB drive or SD card.

(Expert users may remove the USB drive after the message "Got firmware" ... at this stage the file has been read and closed.)

Using the laptop internal drive

An alternate method is to download the firmware file to the laptop internal drive and then install from the internal drive.

  • start the laptop,
  • connect to a wireless or wired network,
su
cd /versions/boot/current/boot/
wget http://dev.laptop.org/pub/firmware/q2f14/q2f14.rom
  • check the battery is inserted and locked,
  • check that the power cord is in place and the battery indicator is green,
  • turn on the laptop, and get to the 'ok' prompt. See Ok for more detail. You should see:
ok
  • if the downloaded file is on an XO-1, type:
flash n:\boot\q2f14.rom
  • if the file is on the internal SD card of an XO-1.5 or XO-1.75:
flash int:\boot\q2f14.rom

Using a network

You will need a compatible USB to ethernet adapter, or an open or WEP wireless access point, connected to the internet.

  • check the battery is inserted and locked,
  • check that the power cord is in place and the battery indicator is green,
  • turn on the laptop, and get to the 'ok' prompt. See Ok for more detail. You should see:
ok
  • if using wireless, type the essid of the wireless network:
essid mynetwork
  • if using a WPA wireless access point, type the WPA key for the network:
wpa passphrase
  • type the flash command using the download link above, but change all slash characters so they are backwards, for example:
flash http:\\dev.laptop.org\pub\firmware\q2f14\q2f14.rom

Secured Laptop

Secured laptops can only use flash firmware that has been signed. All mass-production machines had the latest firmware at the time of manufacture.

Upgrading firmware describes how to upgrade to a newer signed firmware release.

See also

  • Cheat codes for information about how game buttons control startup options.
Retrieved from "http://wiki.laptop.org/mediawiki/index.php?title=OLPC_Firmware_q2f15&oldid=280981"