Embedded controller

From OLPC
Revision as of 03:33, 9 September 2007 by RafaelOrtiz (talk | contribs) (Confirmed for B2)
Jump to navigation Jump to search
  english | español | 한국어 HowTo [ID# 63978]  +/-  
  This page is monitored by the OLPC team.

Introduction

OLPC is now working in an Open Source implementation of the XO's Embedded Controller firmware.

The EC hardware consists of the ENE KB3700 (File:KB3700-ds-01.pdf), which has a 8051 microprocessor at it's core. We have chosen to impliment the firmware in C, using SDCC as our compiler. Efforts are also under way to have CamelForth, a Forth implementation for the 8051, run on the KB3700.

Background

The EC, implemented as a KB3700, has a paramount importance in controlling the XO when the CPU is not active. To do so, the KB3700 communicates with the CPU via the EC protocol, this protocol is managed in the ports 0x66 and 0x62 of the KB3700. These two ports are serially connected with the 0x6C and 0x68 ports of the CPU. (for more info check Ec_specification).

The KB3700 also communicates with the DS2657 (The battery charger) via the 1 wire Dallas protocol. One can deduce part of the internal state of the EC using ec-dump.fth under OpenFirmware. Running the ec-dump script give us valuable data about internals of the EC, being the EC_Register_Settings.

The procedure to run ec-dump over internet in a wireless connection is:

ok wifi media lab 802.11 *change it to your name AP
ok fl http:\\18.85.2.147\~joel\ec-dump.fth *change to your AP IP direction

Running ec-dump over internet and saving the file in a USB key:

ok wifi media lab 802.11 *change it to your name AP
ok fload http:\\18.85.2.147\~rafael\to-file.fth
ok to-file u:\ec-dump fload http:\\18.85.2.147\~joel\ec-dump.fth


OpenEc firmware project

openec is an effort for an open implementation of the firmware on the EC. It currently is in an early stage and not functional yet. Downloading openec to an XO might damage the XO, please do not do so unless you know what you are doing.

Tools for OpenEc

git
source revision tool
sdcc
Compiler sdcc 2.7.0 or later (needed) http://sdcc.sf.net (Compiler which generates the binary for the EC)
gcc
Compiler (optional for openec) the source is currently also compilable with GCC
doxygen
Source documentation tool (optional), http://www.doxygen.org
LaTeX
text tool (optional), needed if a pdf version of the documentation should be generated. A html version of the source documentation can be generated without LaTeX
Srecord
srecord (needed), http://srecord.sf.net, handling of hex (etc.) files (Version 1.36)
Make
(needed), GNU make, should be there anyway.
D52
Disassembler (optional), http://www.8052.com/users/disasm/ , generates disassembled file openec.d52
Download software
spiflash.dic (needed), see http://lists.laptop.org/pipermail/openec/2007-August/000061.html . Forth software to download the EC firmware to the target. Be sure to backup the complete firmware (including manufacturing data) first
Hardware adapter
serial adapter (needed) http://wiki.laptop.org/go/Image:Serial_adapter.jpg Hardware adapter to download to target. Connects to CN24 and an RS232 null-modem cable (an additional oscillator is needed (66MHz(?) to CN24,Pin5)). Additional instructions are at SPI_FLASH_Recovery. (The instructions there address recovery of the complete flash)
Jumpers
2 jumpers for Recovery Mode jumper block (see above)
Null modem cable
(needed) to connect the serial adapter to a serial port
Serial port
(needed) Not all new PC and very few notebooks still have a serial port (an USB to serial adapter might be additionally needed then)
Terminal Software
minicom (recommended). Needed to see or capture debugging output. Parameters 115kBaud, 8N1, no handshake - other terminal programs can be used too.

Related Documentation

http://wiki.laptop.org/go/Category.EC

ENE KB3700 Datasheet

http://sdcc.sourceforge.net/doc/sdccman.pdf

Mailing List

Getting the source

The source is in the git repository OpenEC and can be browsed online there.

To get this code onto your machine please do:

git-clone git://dev.laptop.org/projects/openec

Compiling on the host for the EC

If the necessary tools are installed it is a simple "make" inside the openec directory:

make

Listing files and a binary file currently named openec.do_not_use.bin are generated. (Intentionally no more details here about how to proceed:)

Compiling on the host for the host

Run make with an additional argument inside the openec directory:

make -f Makefile.gcc

you can then run

./openec.gcc | less

there. The EC specific hardware is not present on the host, so openec.gcc will be of limited use. Running openec.gcc on the host does not endanger the host:)

Files of the C implementation

  • battery.c Skeleton for battery handling with the Embedded Controller (key)
  • build.c Keeps version related info
  • compiler.h include file to allow compiling with SDCC and GCC
  • Doxyfile Control file for Source Documentation tool Doxygen
  • ds2756.c Handle Maxim/Dallas DS2756
  • failsafe/ Failsafe Code
  • fs_entry.c Trampoline for a bankswitching routine
  • kb3700.h kb3700.h - header file for ENE KB3700 Keyboard Controler
  • main.c Skeleton for the Embedded Controller of the OLPC project
  • Makefile.gcc Makefile for compiling with GCC
  • Makefile SDCC Makefile
  • matrix_3x3.c Routines to handle 3x3 matrix within the OLPC project
  • openec.ctl Control file for D52 disassembler
  • port_0x6c.c host communication routines for the EC of the OLPC
  • sfr_dump.c dump register settings
  • sfr_rw.c reading/writing mcs-51 sfr (special function registers)
  • states.c Helps debugging state machines
  • timer.c Timer routines for the Embedded Controller of the OLPC project
  • uart.c handle serial IO on the EC
  • unused_irq.c Safe IRQ stubs for unused IRQ
  • watchdog.c Watchdog of the EC

Status

Compilable, timer IRQ functional, blinks LEDs, decodes cursor keys, uart output functional (TX, no RX), dumps registers outputs (ec-dump.fth like) on boot and cursor key press, outputs status of internal state machines onto serial line. Reacts on Power button but does not power up the XO yet.

Status is tested on B1 but yet to be confirmed for others. Confirmed for B2

Desired Features

  • Failsafe Code
  • Easy debugging
  • GCC compilable.

To Do

  • lots