OLPC Firmware q3a62

From OLPC
Revision as of 21:41, 17 December 2010 by Wmb@firmworks.com (talk | contribs) (Q3A62)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to navigation Jump to search
  This page is monitored by the OLPC team.

OLPC Firmware Release q3a62

Fix screen glitch when resuming with rotated display and test /mouse issues.

Works on XO-1.5 A1, A2, B1, B2, B3, C1 ,C2 and C3 systems, but does not work on any XO-1 machines.

Download: q3a62.rom

Changes since q3a61

OpenFirmware svn 2085 Built 2010-12-17 15:54:25

  • svn 2054 - SDHCI - keep track of last 8 commands and display them when an error occurs.
  • svn 2065 - Increase external SD card power-up off time for a 32 G class 10 SD card being tested.
  • svn 2068 - Changed the check for NTLDR to be less language-sensitive.
  • svn 2070 - USB hub driver - added a configurable delay between port power-up and probing.
  • svn 2072 - OLPC trac #10521 - close audio device after playing startup sound so subsequent test /audio works right (resets the sample rate).
  • svn 2076 - SDHCI - restore previous delay for internal slot, adopt 250ms delay following tests with external slot. May be revisited with XO-1.75 A2 where only 1ms may be required.
  • svn 2079 - DSDT, enable THRM# GPIO (ebook) by default.
  • svn 2081 - OLPC trac #10547 - mouse driver was broken due to bad syntax for the unit address.
  • svn 2082 - Avoid set DCONLOAD during resume.
  • svn 2083 - Avoid wait for DCONBLNK.
  • svn 2084 - OLPC trac #10558 - test-all was skipping mouse and keyboard and fixed the mouse driver so it works with the AVC Sentelic touchpads.

EC code is version 2.0.1

  • no change

WLAN firmware is Libertas thinfirm 9.0.7.p2

  • no change


Which Firmware Do You Have?

The best method for finding out what firmware version you have on a laptop depends on whether the laptop is secured or not, and what operating state it is in.

Unsecured Laptop

Obtain the Ok prompt, the firmware version is displayed in the startup banner, thus: 

 OLPC ..., ... memory installed, ..., S/N SHF7250024D
 OpenFirmware  q3a62 ...   EC Firmware Ver:...
               ^^^^^

You can also obtain the built date: 

 ok .built

This is the date and time that this image of the firmware was built by the release engineer.

Secured Laptop

Power up the laptop with the ✓ (check mark) game button held down. You will be asked to Release the game keys to continue. Release the ✓ (check mark) game button and watch carefully. For a short time the startup banner will be displayed, like this: 

 OLPC ..., ... memory installed, ..., S/N SHF7250024D
 OpenFirmware  q3a62 ...   EC Firmware Ver:...
               ^^^^^

Alternatively, if the laptop is already booted, go to the Sugar home view, click on the icon at the centre of the screen and select "My Settings" then "About my Computer." The firmware version is displayed there.

Alternatively, in the Terminal activity or a text console, type: 

 cat /proc/device-tree/openprom/model

or 

 cat /ofw/openprom/model

With certain older firmware versions, if the operating system will not start, and the laptop is secured, you will not be able to obtain the firmware version using the above methods, so our recommendation is to go ahead and upgrade anyway. The procedure is safe and will not do anything if you already have up-to-date firmware.


Installation

When installing new firmware, you must have a well-charged battery and the AC adapter plugged in. The firmware update code will not proceed otherwise. Possible error messages are:

error message how to fix
AC not present plug in the power cord, check the battery LED is on, then try again.
No external power plug in the power cord, check the battery LED is on, then try again,
No battery plug in the battery, check the latches, then try again, or try another battery,
Battery low allow more time for the battery to charge, then try again, or try another battery.

Unsecured Laptop

This section is for unsecured laptops. Most XO-1.5 and XO-1.75 laptops are unsecured. Most developer XO laptops are unsecured. To unsecure your laptop, follow the instructions at Activation and Developer Keys.

You may install using either:

  • a USB drive or SD card,
  • the laptop's internal drive,
  • a network.

Choose one.

Using a USB drive or SD card

  • check the battery is inserted and locked,
  • check that the power cord is in place and the battery indicator is green,
  • insert the USB drive or SD card,
  • turn on the laptop, and get to the 'ok' prompt. See Ok for more detail. You should see:
ok
  • if the downloaded file is on a USB drive, type:
 flash u:\q3a62.rom
  • if the downloaded file is on an external SD card:
 flash sd:\boot\q3a62.rom
  • wait for the laptop to reboot itself,
  • remove the USB drive or SD card.

(Expert users may remove the USB drive after the message "Got firmware" ... at this stage the file has been read and closed.)

Using the laptop internal drive

An alternate method is to download the firmware file to the laptop internal drive and then install from the internal drive.

  • start the laptop,
  • connect to a wireless or wired network,
su
cd /versions/boot/current/boot/
wget http://dev.laptop.org/pub/firmware/q3a62/q3a62.rom
  • check the battery is inserted and locked,
  • check that the power cord is in place and the battery indicator is green,
  • turn on the laptop, and get to the 'ok' prompt. See Ok for more detail. You should see:
ok
  • if the downloaded file is on an XO-1, type:
flash n:\boot\q3a62.rom
  • if the file is on the internal SD card of an XO-1.5 or XO-1.75:
flash int:\boot\q3a62.rom

Using a network

You will need a compatible USB to ethernet adapter, or an open or WEP wireless access point, connected to the internet.

  • check the battery is inserted and locked,
  • check that the power cord is in place and the battery indicator is green,
  • turn on the laptop, and get to the 'ok' prompt. See Ok for more detail. You should see:
ok
  • if using wireless, type the essid of the wireless network:
essid mynetwork
  • if using a WPA wireless access point, type the WPA key for the network:
wpa passphrase
  • type the flash command using the download link above, but change all slash characters so they are backwards, for example:
flash http:\\dev.laptop.org\pub\firmware\q3a62\q3a62.rom

Secured Laptop

Secured laptops can only use flash firmware that has been signed. All mass-production machines had the latest firmware at the time of manufacture.

Upgrading firmware describes how to upgrade to a newer signed firmware release.

See also

  • Cheat codes for information about how game buttons control startup options.
Retrieved from "http://wiki.laptop.org/mediawiki/index.php?title=OLPC_Firmware_q3a62&oldid=250094"