Swap
Swap refers to using storage for data that does not fit into physical random-access memory.
The XO-1 has only 256 MiB of DRAM (see Hardware specifications); adding swap space may allow running more simultaneous instances of more complicated applications.
The XO-1.5, XO-1.75 and XO-4 have more DRAM, so swap space is rarely needed, except for special situations.
How to swap (page) to an SD card
Get a Secure Digital card. You can use a throwaway SD card, these are available for very little. I say throwaway because swapping to it will tend to burn it up faster than its "usual" lifetime for photos and such. You will still be able to use the rest of the card for file storage; about 512 MB will be for swap space. Plug it into the SD card slot on the XO. You'll have to keep it plugged in the whole time while you're swapping to it; you can't remove it the way you remove a USB stick or a non-swap SD card. When it starts to slow down after a few years, you can copy any still-interesting user files off it, throw it away, and put in a new SD card.
Swapping to a partition
You can dedicate a partition on a USB flash drive or SD card to use as swap.
In the Terminal activity or a console, become root. Type mount (and press Enter after this and all other commands), make sure the SD card is mounted at /dev/mmcblk0p1, in a "vfat" filesystem.
Go into the Journal, find the SD card at the lower left (it may be hidden by the Frame), hover over it, choose Unmount. Go back to the terminal.
Type mount, make sure /dev/mmcblk0p1 is not mounted any more. Type yum install parted since the partition editor is not part of the OLPC system software (you'll need to be on the Internet to do this). Run /sbin/parted /dev/mmcblk0. Type print to see the current configuration. On my 1GB SD card it looked like this:
Number Start End Size Type File system Flags 1 127kB 1018MB 1018MB primary fat16
Type resize 1 0 512 to shrink this filesystem down to 512MB. If it asks you whether to use FAT32, say no if your card is 2GB or less. Then type mkpartfs primary linux-swap 512 1018. That'll make a second partition for swapping to, and format it as a Linux swap partition. (If your SD card is a different size, adjust these numbers to give you larger or smaller partitions that fit.) Type print and for a 1GB card it should look roughly like this:
Number Start End Size Type File system Flags 1 32.3kB 512MB 512MB primary fat16 2 512MB 1018MB 506MB primary linux-swap
Type quit to exit parted.
Now you're back to the shell.
Type /sbin/swapon /dev/mmcblk0p2 to add this second partition as a swap device. To have this partition used as swap when the system boots, add this line to /etc/rc.local.
The Hal daemon is smart enough to mount filesystems when it sees an SD card appear, but it's not smart enough to start using freshly available swap space. For the moment, you'll have to enter /sbin/swapon /dev/mmcblk0p2 each time after you insert the card. (Similarly, it won't automatically do a /sbin/swapoff if you try to eject the SD card, but removing swap from a running system is not a good idea.) I'm sure somebody will eventually come up with a Hal script or something to automate this.
Swapping to a file
A file can be used for swap. Here's a way to make a 256 MB swap file on an external filesystem.
- insert the SD card or USB drive,
- hover over the Journal's icon for the drive at the lower left and the Journal will show the path to where it's mounted, something like /mount/VOLUME_NAME
- in a terminal, enter the commands
dd if=/dev/zero of=/media/VOLUME_NAME/swapfile bs=1M count=256 sudo mkswap /media/VOLUME_NAME/swapfile sudo swapon /media/VOLUME_NAME/swapfile
- enter swapon -s to verify the swapfile is being used.
As in the guide for using a swap partition, you'll have to enter sudo swapon /media/VOLUME_NAME/swapfile each time you start, and you mustn't remove the drive without entering sudo swapoff /media/VOLUME_NAME/swapfile.
The jffs2 filesystem can't be used for swap, an error "Invalid argument" occurs.
Swapping to a file on a file system instead of a partition is less efficient, but not notably so. The extra CPU cost of remapping the swap I/O is minimal.
Swap to network block device
Swap can be added as a file on another system, with access over network connection using the network block device driver, which is available as a module.
Advantages:
- swap space can be added when needed rather than always available,
- additional swap space can be added at any time,
- no damage to endurance of SD card or USB drive,
Disadvantages:
- the XO may hang if the other system is shut down,
- the XO may hang if the network connection is lost,
- the network may be loaded,
- disk space is needed on the other system.
Setup the other system:
# install the nbd package sudo yum install -y nbd
# create a 512Mb empty file sudo dd if=/dev/zero of=/root/xo-swap bs=1048576 count=512 # provide it over network block device protocol on port 1234 sudo nbd-server 1234 /root/xo-swap
Setup the XO:
# install the nbd package sudo yum install -y nbd # load the network block device module sudo modprobe nbd # attach the network block device to the remote system sudo nbd-client 10.0.0.1 1234 /dev/nbd0 # make swap space on the block device sudo mkswap /dev/nbd0 # enable swap space sudo swapon /dev/nbd0
Last tested with 13.2.0.
XO-1 swap to loopback block device
XO-1 only. Swap won't attach to a file on internal storage, because of a limitation of the filesystem driver, but this can be bypassed using a loopback block device.
Advantages:
- no additional hardware or network required.
Disadvantages:
- the internal storage is rated for 100,000 writes per cell, the filesystem will try to spread that across the whole device, so this will shorten the life of the internal storage, and it will become permanently slower much earlier than planned by the designers.
Recipe:
# set the name of the swap file FILE=/var/swap
# create the file and preallocate the space dd if=/dev/zero of=$FILE count=32768
# write the swap signature pattern into the file /sbin/mkswap $FILE
# create a loopback block device representing the file LOOP=$(losetup --show --find $FILE)
# turn on swap through the loopback device swapon $LOOP
Last tested on 13.2.0.