Test Network Configuration

Questions

• Is the XO connected to local-link or a mesh?
• Is it connected to an MPP?
• Is it connected to the internet?
• Is it connected to a jabber server?
• What is the ip?

Layer 2

The wireless configuration of the network can be examined using the iwconfig eth0 command. We get MAC layer information such as

1. ESSID
   • olpc-mesh : Indicates a mesh with or without internet connectivity
2. Mode
   • Managed : It is an Access Point(AP) configuration
   • Ad-hoc : It is a mesh configuration(no infrastracture)
3. Frequency
   • 2.412 : Channel 1
   • 2.437 : Channel 6
   • 2.462 : Channel 11
   • Channels 1,6,11 can be used to join a mesh
   • Channel 1 includes a Schoolserver
   • Media lab AP operates on Channels 6 and 11
4. Cell/AP Mac
   • Access Point : The AP's MAC
   • Cell : A virtual 02:xx:xx:... MAC address assigned by the some mesh points. It indicateS mesh configuration

Layer 3

IP addresses

The network layer information can be observed with ifconfig. The eth0 part gives an IPv4 address only if the XO is connected directly to an AP. The address can also indicate a private network. Media lab gives an 18.85.x.x address. The msh0 gives

1. when connected to an AP
   • 169.254.x.x
2. when connected to a school server
   • 172.x.x.x(the current school server in the lab)
   • 10.x.x.x
   • 192.168.x.x
3. when connected in local link
   • 169.254.x.x

DNS check

The most direct way to check internet connectivity is by checking the resolv.conf file. It shows if the XO is registered to a DNS server. It can be viewed with

cat /etc/resolv.conf

• If it is empty there is generally no connection to the internet(technically, no connection to the DNS server)
• If it includes a nameserver with 169.254.x.x address there is internet connectivity through an MPP. The address is in fact the IP of the XO which acts as an MPP
• This is useful to determine on which MPP the XO is connected to, when there are multiple MPPs
• The is a rare possibility resulting from a Network Manager failure, of an XO to have access to the internet, but the resolv.conf to be blank. In that case the XO will not be able to resolve hostnames. This possibility can be examined with

ping www.mit.edu   # No replies
ping 18.7.22.83    # Normal replies  

The general rule of thumb regarding the resolv.conf file in the lab XOs is

• empty: local-link
• 169.254.x.x: MPP
• 172.18.x.x: Schoolserver
• 18.85.x.x: Media lab AP

Telepathy services

The Presence Service acquires information on other XOs in the network, and provides the capability to view them in the neighborhood view, or share with them an activity. This is achieved through two child telepathy services, Salut and Gabble.

Salut

Salut runs when the XO is connected to a mesh. It uses the avahi _presence._tcp service. All XOs in the same mesh indentify themselves in the neighborhood view through Salut. They can be examined through

avahi-browse -t _presence._tcp

Gabble

Gabble will allow XOs that belong to different geographical locations to communicate with each other. It will detect internet connectivity and connect to a Jabber server. All XOs connected to the same jabber server will appear to the neighborhood view. The currently possible servers are

jabber.laptop.org
olpc.collabora.co.uk

• By build 616 the Presence Service does not allow Gabble and Salut to run simultaneously
• It constantly checks whether there is internet connectivity, and switches from Salut to Gabble accordingly
• The XOs displayed in the neighborhood view either belong to the mesh, or the Jabber server, not both
• The internet connectivity does not work very accurately. It is very common when connected to the School server, which provides connectivity, that the XO is running Salut. However, it is convenient in the sense that it can now share activities with others in the mesh.

Detecting which service is running

• The simpler way to detect whether Salut or Gabble is running is by observing the neighborhood view. If you see XOs that you havent seen in the lab then you are probably running Gabble.
• It can also be checked from the Developer's Console - Presence tab - Buddies list - Handles column. The entries either start with ../gabble/jabber/.. or ../salut/local-xmpp/...
• To confirm you are running Gabble you can check the config file for the [Server](not Jabber) entry to be true. This, however, can be misleading, because the file doesnt update properly when you disconnect from the Jabber server. Thus, it usualy includes obsolete information.

$ cat /home/olpc/.sugar/default/config
...
[Server]
registered = True             # running Gabble
server = jabber.laptop.org  

• The console provides a more efficient way of determining with confidence which service is running. The process list will include either a telepathy-salut or a telepathy-gabble process

ps ax                         # general process list
ps U olpc -f|grep telepathy   # only the required entry will be displayed

• Which Jabber server the XO is connected(if its running Gabble) get be examined using the netstat command

netstat -tpT|grep telepathy   # the connection established by the telepathy-gabble process

Combine the tests in an automated script

All the above tests require checking many different locations and running several commands. Alternatively, you can execute this status script, which will accumulate and display the following network overview directly

$bash status

nick      : d01
mac       : 00:17:c4:03:31:fb

ip eth0   : 18.85.18.23
ip msh0   : 169.254.7.84
dns       : 18.85.2.171

essid     : media lab 802.11
channel   : 6

telepathy : gabble
jabber    : jabber.laptop.org

config    : Access point

Useful locations

/etc/resolv.conf
/home/olpc/.sugar/default/config
/home/olpc/.sugar/default/nm/networks.cfg
/etc/NetworkManager/mesh-start

Useful Network and Mesh links

Turn on MPP Capability

Mesh Forwarding Table

Mesh Network Details

Mesh Network FAQ