OLPC Firmware q3a30
OLPC Firmware Release q3a30
This firmware is for the assembly phase of the XO-1.5 C ramp build.
Works on XO-1.5 A1, A2, B1, B2, B3, and C1 systems, but does not work on any XO-1 machines.
Download: q3a30.rom
Open Firmware is svn 1707
Changes since q3a29
- r1707 - Q3A30
- r1706 - XO-1.5 - Added line and curve drawing routines and vector board outline images.
- r1705 - Use new boot-as-call facility so that calling the nandblaster retains Forth execution state - useful for assembly test.
- r1704 - OLPC trac 9997 - Propagate several new method calls through hub nodes, add new "reset-bulk-toggles" method instead of doing it implicitly in set-config (because the bulk pipe numbers are not always known at set-config time, especially in probe-hub).
- r1703 - Checked in thermaltest.fth
- r1702 - Checked in bootascall.fth
- r1701 - Checked in blockfifo.fth
- r1700 - OLPC trac 10003 - added extra delay on S3 resume when USB devices are attached.
- r1699 - OLPC trac 9999 - ext2 file system - Fixed rename problem introduced by svn 1648, and also made it possible to rename directories.
- r1698 - OLPC trac 9998 - ext2 file system - Fixed problem with deleting the last file in a directory.
- r1697 - OLPC trac 9484 - NANDblaster is now working reasonably well in wired mode.
- r1696 - XO-1.5 - Split the versions.fth file into separate files for each versioned component to eliminate unnecessary rebuilding.
- r1695 - OLPC trac 9496 - wrong CPU frequency reported in device tree.
- r1694 - XO-1.5 copynand - deleted more dead code.
- r1693 - Oops on last checkin - XO-1.5 smt.fth wanted-fw should have been q3a29
- r1692 - XO-1.5 smt.fth - wanted-fw set to q3a30
EC code is version 1.9.21
<same as in q3a29>
WLAN firmware is 9.70.7.p0
<same as in q3a14>
Which Firmware Do You Have?
If your machine is not in secure mode, the firmware version is displayed in the startup banner, as in:
OLPC XO 1.5, 1 GiB memory installed, S/N SHF7250024D
OpenFirmware CL1 Q3A04 Q3A
^^^^^
If your machine is in secure mode, you can go to the Terminal activity and type
cat /ofw/openprom/model
If your machine is in secure mode but the OS will not start, just go ahead and try to upgrade the firmware anyway. The procedure is safe and will not do anything if you already have up-to-date firmware.
You can see the firmware version in secure mode by powering up with the "check" game button held down.
You can also go to the main Sugar screen, click on the little man and select "about this XO"
Installation
When installing new firmware, you must have a well-charged battery and the AC adapter plugged in. The firmware update code will not proceed otherwise. Possible error messages are:
| error message | how to fix |
|---|---|
| AC not present | plug in the power cord, check the battery LED is on, then try again. |
| No external power | plug in the power cord, check the battery LED is on, then try again, |
| No battery | plug in the battery, check the latches, then try again, or try another battery, |
| Battery low | allow more time for the battery to charge, then try again, or try another battery. |
Unsecured Laptop
This section is for unsecured laptops. Most XO-1.5 and XO-1.75 laptops are unsecured. Most developer XO laptops are unsecured. To unsecure your laptop, follow the instructions at Activation and Developer Keys.
You may install using either:
- a USB drive or SD card,
- the laptop's internal drive,
- a network.
Choose one.
Using a USB drive or SD card
- download the firmware from http://dev.laptop.org/pub/firmware/q3a30/q3a30.rom and save it to a USB drive or SD card,
- shutdown the laptop,
- check the battery is inserted and locked,
- check that the power cord is in place and the battery indicator is green,
- insert the USB drive or SD card,
- turn on the laptop, and get to the 'ok' prompt. See Ok for more detail. You should see:
ok
- if the downloaded file is on a USB drive, type:
flash u:\q3a30.rom
- if the downloaded file is on an external SD card:
flash sd:\boot\q3a30.rom
- wait for the laptop to reboot itself,
- remove the USB drive or SD card.
(Expert users may remove the USB drive after the message "Got firmware" ... at this stage the file has been read and closed.)
Using the laptop internal drive
An alternate method is to download the firmware file to the laptop internal drive and then install from the internal drive.
- start the laptop,
- connect to a wireless or wired network,
- start the Terminal Activity and type:
su cd /versions/boot/current/boot/ wget http://dev.laptop.org/pub/firmware/q3a30/q3a30.rom
- shutdown the laptop,
- check the battery is inserted and locked,
- check that the power cord is in place and the battery indicator is green,
- turn on the laptop, and get to the 'ok' prompt. See Ok for more detail. You should see:
ok
- if the downloaded file is on an XO-1, type:
flash n:\boot\q3a30.rom
- if the file is on the internal SD card of an XO-1.5 or XO-1.75:
flash int:\boot\q3a30.rom
Using a network
You will need a compatible USB to ethernet adapter, or an open or WEP wireless access point, connected to the internet.
- shutdown the laptop,
- check the battery is inserted and locked,
- check that the power cord is in place and the battery indicator is green,
- turn on the laptop, and get to the 'ok' prompt. See Ok for more detail. You should see:
ok
- if using wireless, type the essid of the wireless network:
essid mynetwork
- if using a WPA wireless access point, type the WPA key for the network:
wpa passphrase
- type the flash command using the download link above, but change all slash characters so they are backwards, for example:
flash http:\\dev.laptop.org\pub\firmware\q3a30\q3a30.rom
Secured Laptop
Secured laptops can only use flash firmware that has been signed. All mass-production machines had the latest firmware at the time of manufacture.
Upgrading firmware describes how to upgrade to a newer signed firmware release.
See also
- Cheat codes for information about how game buttons control startup options.