Repair Manual: Difference between revisions
Jump to navigation
Jump to search
(reassimble -> reassemble) |
(Redirected page to Repair) |
||
| (4 intermediate revisions by 4 users not shown) | |||
| Line 1: | Line 1: | ||
#REDIRECT [[Repair]] |
|||
This page is a work in progress. Please see [[Disassembly]] for how to take apart your XO. |
|||
<!-- This page was a stub that never fleshed out, and has confused a few people. Redirect to Repair which covers Disassembly too. --> |
|||
See Roy Doty's [http://www.roydoty.com/syndicated/wordless-panel.htm Wordless Workshop] for the right way to do this, so it doesn't need translating. |
|||
==XO design requirements and test data== |
|||
*Drop tests |
|||
*Heat tests |
|||
*Liquids |
|||
*Dust and sand |
|||
*Electrical |
|||
*Safety |
|||
==[[Open Firmware]] diagnostics== |
|||
See [[XO-1 OFW Self Test Diagnostics]] |
|||
==Disassembly and reassembly== |
|||
Tools: |
|||
*\#1 Phillips screwdriver |
|||
*3/8"? 8mm? open end wrench or needle-nose pliers |
|||
#Make sure XO is unplugged. |
|||
*(pic: XO closed, no power plugged in) |
|||
#Remove battery |
|||
*(pic: slide battery clips to the sides) |
|||
*(pic: battery removed) |
|||
#Open computer to upright position |
|||
*(pic: antennae raised) |
|||
*(pic: body opened to upright position) |
|||
#Turn screen sideways |
|||
*(pic: screen turned to allow access to screws) |
|||
#Remove two screws on bottom of body. |
|||
*(pic: Show two screws per side) |
|||
*#Turn screen the other way and remove two screws. |
|||
*(pic: Screws removed and put into container) |
|||
#Remove side covers. |
|||
*(pic: two covers, a loose piece under one of them (what is it?), and bared side of XO) |
|||
#Slide screen bezel down and remove. |
|||
*(pic: bezel moved) |
|||
*(pic: bezel removed) |
|||
#Remove loose griefpad. |
|||
*(pic: griefpad location and griefpad) |
|||
#Remove four large screws holding screen |
|||
*(pic: Screen and screws) |
|||
*Slide screen down to reveal two ribbon cable connecters |
|||
*(pic: Screen moved, ribbon cables connected) |
|||
*Using pull tab provided, disconnect screen from small connector. |
|||
*(pic: Cable disconnected) |
|||
*Turn large connector cover up, and with provided pull tab, remove connector. |
|||
*(pic: Second cable removed) |
|||
*Remove screen |
|||
*(pic: XO without screen) |
|||
*Remove four screws holding hinge to base |
|||
*(pic: hinge support) |
|||
*(pic: top section separated from base) |
|||
#Remove screws on main board cover |
|||
*(pic: Cover slid down) |
|||
*(pic: Main board uncovered) |
|||
#Remove screws on metal plate on main board |
|||
*(pic: Board and plate) |
|||
#Remove screws on main board |
|||
*(pic: Main board slid out) |
|||
#Unscrew and remove green plastic bits on keyboard assembly |
|||
*(pic: ) |
|||
*(pic: ) |
|||
*(pic: ) |
|||
*(pic: ) |
|||
#Remove back of keyboard |
|||
*(pic: ) |
|||
#Disconnect keyboard |
|||
*(pic: Keyboard slid out) |
|||
*(pic: Keyboard removed) |
|||
*(pic: ) |
|||
*(pic: ) |
|||
*(pic: ) |
|||
*(pic: ) |
|||
*(pic: ) |
|||
*(pic: ) |
|||
*(pic: ) |
|||
*(pic: ) |
|||
*(pic: ) |
|||
*(pic: ) |
|||
*(pic: ) |
|||
*(pic: ) |
|||
*(pic: ) |
|||
*(pic: ) |
|||
*(pic: ) |
|||
To reassemble, just reverse the procedure above. |
|||
==Frankenputers== |
|||
==Battery life== |
|||
==Recycling== |
|||
Latest revision as of 13:49, 19 May 2010
Redirect to: