Multi channel battery charger: Difference between revisions
Jump to navigation
Jump to search
m (remove Category:MBC, this is the only page in it.) |
|||
| (14 intermediate revisions by 7 users not shown) | |||
| Line 1: | Line 1: | ||
| ⚫ | |||
| ⚫ | |||
{{OLPC}} |
{{OLPC}} |
||
This page describes a charger for multiple [[Hardware#XO_Laptop|XO Laptop]] batteries. |
|||
{{draft}} |
|||
== Introduction == |
|||
= Multi Channel Battery Charger = |
|||
[[Image:Multi-Battery_Charger.png|300px|right]] |
|||
Code name "Supercharger" |
|||
== |
|||
== Input Power == |
|||
* AC Power 100V-230V. 300W |
* AC Power 100V-230V. 300W |
||
* DC 10V-28V. 150W |
* DC 10V-28V. 150W |
||
| Line 15: | Line 14: | ||
* AC In: IEC for 120/220VAC |
* AC In: IEC for 120/220VAC |
||
* DC In: 10VDC to 28VDC 2 Pin connector that mates with whats on the GP solar blanket. |
* DC In: 10VDC to 28VDC 2 Pin connector that mates with whats on the GP solar blanket. |
||
** DC connector is not yet finalized |
|||
* USB B connector (Its a USB device) |
* USB B connector (Its a USB device) |
||
* 2 cables with XO DC jacks on them |
* 2 cables with XO DC jacks on them |
||
| Line 27: | Line 27: | ||
* Forth/C combination. |
* Forth/C combination. |
||
* http://dev.laptop.org/git |
* http://dev.laptop.org/git/projects/supercharger |
||
== |
== Function == |
||
* Approximately 2 hours for complete charge |
|||
* '''Density'''. Getting as many batteries as possible in as small a footprint is a goal. |
|||
** Maximum number of simultaneous charging channels |
|||
*** 15 Batteries on AC |
|||
* '''Physical Safety'''. Its got to be stable and hold lots of heavy batteries but not be able to fall over on top of a child who might be trying to climb on it to get his battery. |
|||
*** 10 Batteries via 150W DC source |
|||
*** 8 Batteries via 2 60W solar blankets |
|||
* '''Stackable'''. More vertical space is available than floor sq footage so an idea was to make them stackable. But see above point. |
|||
*** 4 Batteries via 1 60W blanket |
|||
* '''Heat dissipation'''. Input stage power supply is about 85% (DC/DC may be higher). 2nd stage is 82%. So while on DC heat dissipation will be around 64 Watts and on AC around 98 Watts. (Calculated. Not yet measured) |
|||
* '''Enclosure'''. Metal. Except perhaps for some plastic for the battery holder. Having metal available to heatsink to should help in keeping the electronics from burning up in hot countries. |
|||
== Datasheets == |
== Datasheets == |
||
| Line 44: | Line 41: | ||
* [[Image:At91sam7x128_256_pc.pdf]] Atmel CPU |
* [[Image:At91sam7x128_256_pc.pdf]] Atmel CPU |
||
* [[Image:DS2756.pdf|DS2756]] DS2756 |
* [[Image:DS2756.pdf|DS2756]] DS2756 |
||
| ⚫ | |||
| ⚫ | |||
Latest revision as of 08:49, 14 March 2011
This page is monitored by the OLPC team.
This page describes a charger for multiple XO Laptop batteries.
Introduction
Code name "Supercharger"
Input Power
- AC Power 100V-230V. 300W
- DC 10V-28V. 150W
Exterior Connections
- AC In: IEC for 120/220VAC
- DC In: 10VDC to 28VDC 2 Pin connector that mates with whats on the GP solar blanket.
- DC connector is not yet finalized
- USB B connector (Its a USB device)
- 2 cables with XO DC jacks on them
Electrical Misc
- The CPU is an Atmel At91SAM7x family part.
- The per battery DC-DC charger is a SEPIC design based around a MicroChip MCP1631 part
Software
- Forth/C combination.
- http://dev.laptop.org/git/projects/supercharger
Function
- Approximately 2 hours for complete charge
- Maximum number of simultaneous charging channels
- 15 Batteries on AC
- 10 Batteries via 150W DC source
- 8 Batteries via 2 60W solar blankets
- 4 Batteries via 1 60W blanket
- Maximum number of simultaneous charging channels
Datasheets
- File:At91sam7x128 256 pc.pdf Atmel CPU
- File:DS2756.pdf DS2756