Making XO sensors/Lichtsensor: Difference between revisions
Jump to navigation
Jump to search
No edit summary |
No edit summary |
||
| Line 2: | Line 2: | ||
Lichtsensor Kit: |
Lichtsensor Kit: |
||
* 1 |
* 1 Photowiderstand (rot: center, schwarz: Erdung, weiß: tip)(light dependent resistor),[http://www.parallax.com/Store/Sensors/ColorLight/tabid/175/CategoryID/50/List/0/SortField/0/Level/a/ProductID/175/Default.aspx] [http://www.jaycar.com.au/productView.asp?ID=RD3480] [https://www.radioshack.com/product/index.jsp?productId=2062590] |
||
* 1 Lichtsensor |
* 1 Lichtsensor |
||
* 1m Isolierband |
* 1m Isolierband |
||
| Line 10: | Line 10: | ||
|- |
|- |
||
| [[Image:Light sensor 01.jpg|400px]] |
| [[Image:Light sensor 01.jpg|400px]] |
||
| Wir kappen den Kabelmantel ca. 4 cm und verbinden und die Drahtisolierung des schwarzen und weißen Kabels. Anschließend verbinden wir den Lichtsensor mit dem freigelegten abisolierten Draht weiß und schwart miteinander indem wir den weißen Draht um den einen Draht des Sensors wickeln und den schwarzen Draht um den Anderen. |
|||
| As shown in the picture, tear the two ends of the wire apart (as you did when making a plug) and use a Stripper to strip the wire bare. |
|||
Slide on the X (heat-compressible rubber tubing) onto both ends of the wire as shown. Only one side is shown in the picture, but follow the same process for the other wire. |
|||
Next, use the soldering iron to connect the two ends of the wire to the two ends of the sensor. This can be done by adding some solder to the two end contact points of the sensor and to the bare ends of the wire. Subsequently, join the two together as shown in the picture, and allow the solder to cool, solidify and thus connect. |
|||
|- |
|- |
||
| [[Image:Light sensor 02.jpg|400px]] |
| [[Image:Light sensor 02.jpg|400px]] |
||
Revision as of 21:33, 22 October 2012
Lichtsensor Kit:
- 1 Photowiderstand (rot: center, schwarz: Erdung, weiß: tip)(light dependent resistor),[1] [2] [3]
- 1 Lichtsensor
- 1m Isolierband
- 1 Schere
|
Wir kappen den Kabelmantel ca. 4 cm und verbinden und die Drahtisolierung des schwarzen und weißen Kabels. Anschließend verbinden wir den Lichtsensor mit dem freigelegten abisolierten Draht weiß und schwart miteinander indem wir den weißen Draht um den einen Draht des Sensors wickeln und den schwarzen Draht um den Anderen. |
|
Next, slide the rubber tubing up the wire so that it completely covers the two contact points, and then use X (hot air) to compress the rubber tubing onto the wire. |
|
A finished light sensor! |
Other sensor instructions
- Making XO sensors/Construir Sensor Luz
- Making XO sensors/How to connect sensors
- Making XO sensors/Lichtsensor
- Making XO sensors/Making a Humidity Sensor
- Making XO sensors/Making a Light Sensor
- Making XO sensors/Making a Magnetic Sensor
- Making XO sensors/Making a Switch Sensor
- Making XO sensors/Making a Temperature Sensor
- Making XO sensors/Making a Thermistor