Installing to NAND: Difference between revisions

From OLPC
Jump to navigation Jump to search
m (Reverted edits by 219.240.36.175 (219.240.36.175); changed back to last version by 65.96.160.183)
No edit summary
Line 13: Line 13:
==Procedure==
==Procedure==


After the board has booted, hit ctrl+alt+F1 to get to a login prompt, and login as root. Then:
After the board has booted, hit ctrl alt F1 to get to a login prompt, and login as root. Then:


modprobe mtdchar
modprobe mtdchar
Line 34: Line 34:
=== I see a hang after "<tt>NOTICE: Booting default</tt>" ===
=== I see a hang after "<tt>NOTICE: Booting default</tt>" ===


This is normal: the filesystem on the NAND flash is being uncompressed. It should last for around 80 seconds. (Yes, this is slow! The Geode's flash-memory controller performance is very slow. On future boards&mdash;the production hardware&mdash;we'll have a separate flash-memory controller that will be providing an order of magnitude greater performance.)
This is normal: the filesystem on the NAND flash is being uncompressed. It should last for around 80 seconds. (Yes, this is slow! The Geode's flash-memory controller performance is very slow. On future boards

=== <tt>JFFS2 warning: (1381) jffs2_sum_write sumnode: Not enough space for summary, padsize = -793</tt> ===

This warning is harmless.

=== <tt>Skipping bad block at 0xnnnn0000</tt> ===

During flash_eraseall, this is normal. See procedure section above.



== Timing ==

* '''Flash_eraseall''' takes roughly 14 seconds,
* '''Nandwrite'''andwrite takes roughly 54 seconds when the input file is taken from a USB 2.0 key.

[[Category:Developers]]

Revision as of 14:03, 22 June 2007

Auto Installer

The data in this page is a bit outdated. There are better methods now. Please see Autoreinstallation image

Overview

Please try installing to NAND flash now, and report any difficulties.

This page describes how to write a filesystem to the board's internal NAND flash and boot from it using LinuxBIOS.

Requirements

You should have a working install of one of the OLPC Build images, build 79 or higher, and a copy of the corresponding jffs2.img for that build available. (For example, on another USB key, or on another partition of the same key if it is larger than 512M.)

Procedure

After the board has booted, hit ctrl alt F1 to get to a login prompt, and login as root. Then:

  modprobe mtdchar
  flash_eraseall -j /dev/mtd0
  nandwrite -p /dev/mtd0 /path/to/olpc-development-rpm-jffs2.img

We intend to provide a mechanism to let the jffs2 img be streamed to nandwrite over the network, for people with only one USB key; this isn't working currently, though.

It is normal to see bad block errors during both the flash_eraseall; NAND flash comes from the factory with bad blocks marked. You may also see error messages during the nandwrite step. When the nandwrite has finished you can reboot, and LinuxBIOS will boot from the NAND flash.

Troubleshooting

flash_eraseall: /dev/mtd0: No such file or directory

This is seen when modprobe mtdchar wasn't performed.

NOTE: You'll get the very same error if you don't Upgrade to LinuxBIOS first.

I see a hang after "NOTICE: Booting default"

This is normal: the filesystem on the NAND flash is being uncompressed. It should last for around 80 seconds. (Yes, this is slow! The Geode's flash-memory controller performance is very slow. On future boards