Disassembly bottom: Difference between revisions

From OLPC
Jump to navigation Jump to search
Line 61: Line 61:
<br style="clear:both" />
<br style="clear:both" />


=== Step 5 ===
== Replacing the keyboard ==

=== Step 1 ===


[[image:Keyboardstep5a.jpg|thumb|left|Put in the new keyboard, making sure that it lies flat.]] [[image:Keyboardstep5b.jpg|thumb|left|Replace the two screws near the handle.]] [[image:Keyboardstep5c.jpg|thumb|left|Carefully replace the keyboard/touchpad board.]]
[[image:Keyboardstep5a.jpg|thumb|left|Put in the new keyboard, making sure that it lies flat.]] [[image:Keyboardstep5b.jpg|thumb|left|Replace the two screws near the handle.]] [[image:Keyboardstep5c.jpg|thumb|left|Carefully replace the keyboard/touchpad board.]]
<br style="clear:both" />
<br style="clear:both" />

[[image:Keyboardstep5d_pickrightscrew.jpg|thumb|left|Make sure to use the right screws! You'll need the short silver ones.]] [[image:Keyboardstep5d.jpg|thumb|left|Using those screws, fasten the board and edges of the keyboard.]] [[image:Keyboardstep5e.jpg|thumb|left|Put the green edge piece back in.]] [[image:Keyboardstep5f.jpg|thumb|left|Replace the ribbon cables.]]
=== Step 2 ===
[[image:Keyboardstep5d_pickrightscrew.jpg|thumb|left|Make sure to use the right screws! You'll need the short silver ones.]] [[image:Keyboardstep5d.jpg|thumb|left|Using those screws, fasten the board and edges of the keyboard.]] [[image:Keyboardstep5e.jpg|thumb|left|Put the green edge piece back in.]]
<br style="clear:both" />
<br style="clear:both" />

=== Step 3 ===
[[image:Keyboardstep5f.jpg|thumb|left|Replace the ribbon cables.]]
[[image:Keyboardstep5g.jpg|thumb|left]] [[image:Keyboardstep5h.jpg|thumb|left]] [[image:Keyboardstep5i.JPG|thumb|left]]
[[image:Keyboardstep5g.jpg|thumb|left]] [[image:Keyboardstep5h.jpg|thumb|left]] [[image:Keyboardstep5i.JPG|thumb|left]]
<br style="clear:both" />
<br style="clear:both" />

Revision as of 18:31, 29 May 2008

XO before disassembly

Keyboardstep0.jpg


Opening the handle / reaching the spare screws

Step 1

Remove the battery.
Take out the five screws under the battery case.


Step 2

Pull off the white panel on the handle.


Keyboardstep1d.jpg
Notice the 6 extra screws in the handle.


Removing the hinge / disconnecting the top and bottom halves of the XO

Step 1

Unplug the connection between the battery and computer.


Step 2

Unscrew the hinge.


Step 3

You can now separate the top half of the XO from the bottom half.
Set the top half of the XO aside.


Removing the bottom cover

Step 1

Remove the four screws in the handle.
Pull out the green piece on the edge of the handle.
Push down the bottom of the laptop.
The bottom should come off as one piece.


Removing the ALPS (touchpad and keyboard control) board

Step 1

Unstick the cable connecting the computer to the keyboard.
Unplug the cable from the touchpad/keyboard.
Keyboardstep3c.jpg
Disconnect the ribbon cables from the keyboard/touchpad board.


Step 2

Keyboardstep3e.jpg
Keyboardstep3f.jpg
Remove the four screws holding in the green piece (the ALPS board) at the edge of the touchpad area.
Keyboardstep3h.jpg


Step 3

Pull up the silver tape tabs to free the keyboard.
Keyboardstep3j.jpg
Remove four screws as shown. Note that these are shorter than the standard ones
Remove the ALPS board.


Removing the keyboard

Step 1

Remove the last two screws holding in the keyboard.
Pull the green side panels apart to free the board.
Pull out the keyboard.
Keyboardstep4d.jpg


Replacing the keyboard

Step 1

Put in the new keyboard, making sure that it lies flat.
Replace the two screws near the handle.
Carefully replace the keyboard/touchpad board.


Step 2

Make sure to use the right screws! You'll need the short silver ones.
Using those screws, fasten the board and edges of the keyboard.
Put the green edge piece back in.


Step 3

Replace the ribbon cables.
Keyboardstep5g.jpg
Keyboardstep5h.jpg
Keyboardstep5i.JPG


Step 6

Plug the connection cable back in.
Stick the connection cable down so that it doesn't slip.
Replace the white bottom panel. This can be a little tricky, so make sure it sits flat.


Snap the side panels in to hold the bottom panel.
Replace the green edge piece on the handle.
Put in the four screws in the handle.


Reseat the hinge.
Latching the XO shut can help hold it in place.
Make sure to use the long silver screws on the hinge.
Screw down the hinge.


Step 7

Replace the white handle cover.
Keyboardstep7b.jpg
Put in the last five screws, that go in under the battery.


Keyboardstep7d.jpg
Finished!