XO-1/Software specification: Difference between revisions

From OLPC
Jump to navigation Jump to search
Line 44: Line 44:


====Quiet Boot====
====Quiet Boot====

Boot is not "quiet" at this time. Linux has facilities to make a splash screen at boot overlay the boot messages, but OLPC has not implemented this as yet. [http://dev.laptop.org/ticket/1394 Bug #1394] tracks this issue for eventual resolution.

====POST Message====
====POST Message====
====Open Firmware Command Prompt====
====Open Firmware Command Prompt====

Revision as of 01:36, 4 May 2007

  This page is monitored by the OLPC team.
  Please copy/paste "{{Translationlist | xx | origlang=en | translated={{{translated}}}}}" (where xx is ISO 639 language code for your translation) to XO-1/Software specification/translations HowTo [ID# 36433]  +/-  


Power Management

Introduction and Related Material

Careful stewardship of battery power is critical.

This page is a work in process, collecting information related to power management on OLPC.

In addition to effectively managing the power that is in the battery. The Battery and power page discusses many alternate power sources that could be used to supplement the existing charger.

Linux's Approach to Power Control

Linux is highly cross platform, running on just about all significant architectures, including many that are used for battery powered embedded systems. The infrastructure for power management has therefore become quite sophisticated over the last years, though it is still maturing. This means that the facilities are general, and not tied to any particular architecture. The generation one OLPC system, being from the x86 part of the world, is therefore similar and fundamentally different from other x86 based systems, for reasons that will become clear in the discussion below.

Linux is not dependent on ACPI or the older APM power management systems, which are x86 specific. As such, Linux's design has always done its power control in the operating system, and ACPI and the like are considered "platform dependent".

OLPC's Innovations

The DCON chip lets us take over refresh of our very low power flat panel and therefore completely power off the processor board. Given our flat panel is usable in gray scale mode at .1 watt, you can see that the leakage currents and power supply power consumption of the system board can dominate power consumption easily.

We are also able to leave the Marvell wireless module to operate independently, forwarding packets in the mesh while possibly everything else is powered down.

Use of Open Firmware

Rather than using a conventional BIOS and boot loader, as of the "C" series of our firmware we are using Open Firmware. We no longer use LinuxBIOS for the setup of our systems. This is a result of having implemented fast past resume from RAM; once you have implemented this, setup of the system initially is almost identical.

We have also removed VSA and VESA support (the Geode Virtual Systems Support) from our firmware. Since our PCI bus is fixed, we have no need for PCI configuration registers. Similarly, using the fbdev driver on Linux, we have no need for VESA emulation; while the PCI bus emulation was free software (AMD had generously made it available), the VESA emulation was the one part of VSA that they did not own, and so we did not have source for it. We did not want an unmaintainable binary blob in our firmware that we did not need anyway.

Fast Resume

Resume on our system is extremely fast: even without any serious attempt to optimize resume, we can resume from RAM in 160 milliseconds (mid-April). We believe the hardware limitations for resume are about 63 milliseconds on the B2 and before systems; B3 and later are probably similar. We will do work in the future to further speed resume. Note that for most uses, 100ms is considered at the edge of human perception (e.g. typing).

BIOS

General

System Identification

The [Manufacturing Data] page documents the Model ID string, part number, localization information, factory, BIOS version, and many other pieces of data.

Quiet Boot

Boot is not "quiet" at this time. Linux has facilities to make a splash screen at boot overlay the boot messages, but OLPC has not implemented this as yet. Bug #1394 tracks this issue for eventual resolution.

POST Message

Open Firmware Command Prompt

Power Management Support

Power Button

Power Management States

End user visible operating states

The following are the major operating states of the system. For simplicity's sake, see Wikipedia's ACPI article.

Powered Down

In this state, (in ACPI terminology, G3 is this state). Everything is off and the battery can be swapped. The operating system will have to be booted to start operation; the RAM is not preserved. On our hardware, if power is available, the EC will be powered up and potentially charging the battery.

Suspended, with Mesh Active, No screen

A common mode of use will be the system not being used, but still active forwarding in the mesh network on behalf of others in the mesh, but otherwise unused. This differs from our powered down state by the fact the Marvell wireless will be powered up, and active. In ACPI terminology, the closest match is G1/S3. The processor is suspended to RAM (in self-refresh).

Suspended, with Mesh Active, Screen Alive
System fully operational

Lid Close Switch

Thermal Management

Configuration

Boot Configuration

Device Tree

Video RAM

System Resources

IRQ Map

DMA Map

Status Indicators

LED Support

Security

Firmware Recovery

Special Function Keys

Video

Wirelesss

System Managemetn BIOS Interface

Not Supported

Battery Subsystem

Hardware Power Management

Device Tree Support

Power Management

Device Power Down

Sleeping States

Thermal Management

Lid Close

PCI Subsystem ID's=

Keyboard Languages Support

CPU Support

Memory Module Support

Wireless Devices

One Touch Buttons

Platform Software

Screen

DCON mode

Refresh Rate

GPU Powered Up

Audio

USB

Keyboard/Touchpad