Hardware specification/lang-de

From OLPC
< Hardware specification
Revision as of 13:43, 13 April 2007 by Weschii360 (talk | contribs)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to navigation Jump to search
  Diese Seite wird überwacht durch das OLPC-Team.
  Please copy/paste "{{Translationlist | xx | origlang=en | translated={{{translated}}}}}" (where xx is ISO 639 language code for your translation) to Hardware specification/lang-de/translations HowTo [ID# 33317]  +/-  


Hardware

Der XO-Laptop bildet den Mittelpunkt von One Laptop Per Child. Nach zwei Jahren Entwicklung, gepaart mit tausenden von Beta-Tests, Schweissblut von vielen Entwicklern und jede Menge Tests in Schulen in ausgesuchten Ländern. Das Design des Laptops wurde so konstruiert, um die technologischen Vorteile der Neuzeit einfliessen lassen zu können.


Spezifikationen

  • Grafikkontroller: Integriert im Geode-Prozessor; unified memory architecture
Drawing75c1.jpg

physikalische Dimensionierung:

  • Abmessungen: 242mm × 228mm × 30mm (ungefähre Angaben)
  • Gewicht: geringer als 1,5 kg
  • Konfiguration: Einstellbares Notebook mit verdrehbarem Display; Schmutz- und Nässebestädigkeit integriert.

Elektronik:

  • CPU: AMD Geode LX-700@0.8W
  • CPU Geschwindigkeit: 433 Mhz
  • Kompatibilität: Athlon instruction set (integrierte MMX- und 3DNow! Enhanced- Technologie) mit zusätzlichen Geode-spezifischen Eigenschaften
  • North Bridge: PCI- und Speicherinterface integriert im Prozessor
  • Grafikkontroller: Integriert im Prozessor


  • South Bridge: AMD CS5536 (datasheet)
  • DRAM memory: 256 MiB dynamic RAM
    • Data rate: Dual – DDR333 – 166 Mhz
  • BIOS: 1024 KB SPI-interface flash ROM; LinuxBIOS open-source BIOS; Open Firmware bootloader
  • Mass storage: 1024 MiB SLC NAND flash, high speed flash controller
  • Drives: No rotating media
  • Embedded Controller: ENE KB3700: File:KB3700-ds-01.pdf
Prototype-A Motherboard

Display:

  • Liquid-crystal display: 7.5” Dual-mode TFT display
  • Viewing area: 152.4 mm × 114.3 mm
  • Resolution: 1200 (H) × 900 (V) resolution (200 dpi)
  • Mono display: High-resolution, reflective monochrome mode
  • Color display: 800 (H) x 600 (V) or greater transmissive color mode
  • Power Consumption: 0.1 Watt with backlight off; 0.2-1.0 Watt with backlight on
  • The DCON - Display Controller chip with memory that enables the display to remain live with the processor suspended. The display and this chip are the basis of our extremely low power architecture. The machine is usable and relaying mesh networking traffic while the CPU and much of the motherboard is regularly turned off. The display controller chip also enables deswizzling and anti-aliasing in color mode. You can examine this photograph of the display (it looks even nicer in person; photographing a display is remarkably difficult).
Note: web browser images are currently scaled up so that an image of very roughly [800x600] fills up the browser window.
eToys (Squeak)running on the OLPC display

Integrated peripherals:

Keyboard detail
  • Wireless: Marvell Libertas 88W8388+88W8015, 802.11b/g compatible; dual adjustable, rotating coaxial antennas; supports diversity reception
  • Status indicators: Power, battery, WiFi; visible lid open or closed
  • Video camera: 640x480 resolution, 30FPS
  • Independent and undefeatable by software display of microphone and camera recording status

External connectors:

  • Power: 2-pin DC-input, 10 to 20 V usable input. Input can safely handle -40 to 39 V. input. Exceeding this range will likely blow a one-time fuse.
  • Line output: Standard 3.5mm 3-pin switched stereo audio jack
  • Microphone: Standard 3.5mm 2-pin switched mono microphone jack; selectable input mode:
    • Sensor, DC w. 2.5 V (3K ohm impledance) bias voltage for switches, resistive sensors, etc.
    • Sensor, DC w. no bias voltage for measuring voltages (0 - 3 V)
    • External Microphone, AC w. bias voltage
  • Expansion: 3 Type-A USB-2.0 connectors; MMC/SD Card slot
  • Maximum power: 1 A (total)
Connectors

Battery:

  • Fully-enclosed “hard” case; user removable
  • Pack type: 4 Cells, 6V series configuration
  • Two chemistries:
    • NIMH, with a capacity of 16.5 Watt-hours
    • LiFeP, with a capacity of 22 Watt-hours
  • Electronics integrated with pack provide:
    • Identification
    • Battery charge and capacity information
    • Thermal and over-current sensors along with cutoff switch to protect battery
  • Cycle life: Minimum 2,000 charge/discharge cycles (to 50% capacity of new, IIRC).
  • Power Management will be critical
Battery

BIOS/loader:

  • LinuxBIOS is our BIOS for production units; Open Firmware is used as the bootloader.

Environmental specifications:

  • Temperature: somewhere in between typical laptop requirements and Mil spec; exact values have not been settled
  • Humidity: Similar attitude to temperature. When closed, the unit should seal well enough that children walking to and from school need not fear rainstorms or dust.
  • Altitude: -15m to 3048m (14.7 to 10.1 psia) (operating), -15m to 12192m (14.7 to 4.4 psia) (non-operating
  • Shock: 125g, 2ms, half-sine (operating) 200g, 2ms, half-sine (non-operating)
  • Random vibration: 0.75g zero-to-peak, 10Hz to 500Hz, 0.25 oct/min sweep rate (operating); 1.5g zero-to-peak, 10Hz to 500Hz, 0.5 oct/min sweep rate (nonoperating)
  • 2mm plastic walls (1.3mm is typical for most systems).

Regulatory requirements:

  • The usual US and EU EMI/EMC requirements will be met.
  • The laptop and all OLPC-supplied accessories will be fully UL and is RoHS compliant.

Laptop Development Schedule

The XO laptop hardware development schedule has two more test unit builds (Beta Test 3 and Beta Test 4), before a final test build (C Test 1) on the final production line and mass production. The Beta Test 3 build scheduled for early May will be the first one providing the processor and memory capabilities of the production version.

Pre-production Test Systems (CTest-1, or C1)

This build is a very small number (200 or so) of laptops produced as a test of the manufacturing process on the main production line, and should happen in early fall. A C1 laptop is hopefully identical to a production unit in all aspects...

Beta Test 4 Systems (BTest-4, or B4)

This build, scheduled for the middle of the summer, is the final chance to fix hardware and mechanical problems that were detected in the Beta Test 3 build of the XO. Only a small number (200 or so) of these will be built for testing, as the injection molds for the plastic case have to be taken offline and duplicated to prepare for mass production (the Beta Test mold set will be retired after duplication).

No new features will be added to the laptop in this build. This build is planned merely to test solutions to problems detected in the BTest-3 laptops.

Beta Test 3 Systems (BTest-3, or B3)

This build, scheduled for May, is the first to use an updated design for the laptop. Noticeable improvements over BTest-2 include:

  • A faster, lower power processor: the Geode LX-700
    • 128 KB of L1 Cache, 128 KB of L2 Cache (vs. 32 KB of L1 cache)
    • Faster processor and memory clock (433/333 vs. 366/266)
    • 1.5 W typ. vs. 3 W typ.
    • Much better graphics processor, including support for rotated blits and depth conversion
  • More memory: 256 MB of SDRAM (vs. 128 MB)
  • A new hinge design allows greater tilt of the screen
  • An improved case design (addressing strength and water resistance)

A very small number of BTest-3 units (around a hundred) will be built, all destined for hardware and low level software development.

Beta Test 2 Systems (BTest-2, or B2)

Approximately 2500 systems were built by Quanta and are being distributed. These are fully functional machines with CaFE asic's, and reflect some, but not all of the learning and improvements from testing of BTest-1. Much more information about the BTest-2 systems can be found in the BTest-2 Release Notes. Some of the details of the hardware design are to support the OLPC Human Interface Guidelines.

BTest-2 systems are almost identical visually with BTest-1. BTest-3 will have more substantial physical differences. An easy way to tell the difference between BTest-1 and BTest-2 is that BTest-1 keyboards have white lettering, and BTest-2 has black lettering.

Beta Test 1 Systems (BTest-1)

Approximately 875 systems were built by Quanta and were distributed. These are fully functional machines, but built before the rigorous testing that will now take place. Much more information about the BTest-1 systems can be found in the BTest-1 Release Notes.

Pre-BTest boards

A small number of pre-BTest boards were built in preparation for building complete BTest systems. Developer information about B-test boards are here.

Alpha Test Prototype Electronics

Power up of the first OLPC electronics prototype boards occurred April 15, 2006. Power and ground testing continued over the weekend, and formal debug and BIOS bring up started Monday, April 17, 2006 at Quanta Computer's labs in Taipei, Taiwan. By Wednesday, April 19, Linux was booting on the first generation prototypes.

Photographs:

See also

Formerly part of this page:


School Server Hardware

While the laptop is rightfully at the center of OLPC, a valuable peripheral is the school server. OLPC will be building and distributing school servers along with the laptops, to extend the storage and computation provided by each laptop, as well as providing a local library and a mesh portal to the Internet.

Unlike the laptop, the school server is more of a collection of services than a hardware platform. In a manner identical to the laptop, OLPC will collaborate with manufacturing partners to provide a cost-efficient hardware platform for running the recommended software. Unlike the laptop, the manufacturing collaboration will not be exclusive. Individual countries will be free (even encouraged) to design and manufacture their own school servers running derivatives of the OLPC school server software.

XS

This will be the school server built for OLPC by Quanta. It is still in the very early stages of design, but should reach early production volumes in late fall. See the specification.

XSX

This is a prototype school server, built for early school trials in country. It will be integrated from off-the-shelf components, and will be overpowered compared to a production school server in order to simplify early demands for system software. See the specification and the implementation.