Hardware specification

From OLPC
Revision as of 19:18, 24 August 2007 by MitchellNCharity (talk | contribs) (→‎Core electronics: fixed CaFE Specification link)
Jump to navigation Jump to search
  This page is monitored by the OLPC team.
  deutsch | english | español | français | italian | 日本語 | 한글 | português | русский indonesia HowTo [ID# 61520]  +/-  


Laptop Hardware

The XO laptop is the center of One Laptop Per Child. After two years of development, it is approaching mass production, with several thousand Beta test (B2) units deployed to developers and for testing in schools in participating countries. The laptop design has just undergone a final minor update to keep up with advancements in technology.

Specifications

Drawing75c1.jpg

Physical dimensions

  • Approximate dimensions: 242mm × 228mm × 32mm;
  • Approximate weight:
    • XO laptop with LiFeP battery: 1.45KG;
    • XO laptop with NiMH battery: 1.58KG;
  • Configuration: Convertible laptop with pivoting, reversible display; dirt- and moisture-resistant system enclosure; no fan.

Core electronics

  • CPU: x86-compatible processor with 64KB each L1 I and D cache; at least 128KB L2 cache;
  • CPU clock speed: 433 Mhz;
  • ISA compatibility: Support for both the MMX and 3DNow! x86 instruction-set extensions;
    • Athlon instruction set (including MMX and 3DNow! Enhanced) with additional Geode-specific instructions
  • Companion chips: PCI and memory interface integrated with CPU;
  • Graphics controller: Integrated with CPU; unified memory architecture;
  • Embedded controller: ENE KB3700 or ENE KB3700B;
  • DRAM memory: 256 MiB dynamic RAM; data rate: dual-DDR333-166Mhz;
  • BIOS: 1024KiB SPI-interface flash ROM;
  • Open Firmware used to load the operating system;
  • Mass storage: 1024 MiB SLC NAND flash, high-speed flash controller;
  • Drives: No rotating media.
  • CaFE ASIC (Camera, Flash Enabler chip, provides high performance Camera, NAND FLASH and SD interfaces). Marvell 88ALP01: CaFE Specification
Prototype-A Motherboard

Display

  • Liquid-crystal display: 7.5” dual-mode TFT display;
  • Viewing area: 152.4 mm × 114.3 mm;
  • Resolution: 1200 (H) × 900 (V) resolution (200 DPI);
  • Monochrome display: High-resolution, reflective sunlight-readable monochrome mode;
  • Color display: Standard-resolution, quincunx-sampled, transmissive color mode;
  • Special DCON chip that enables deswizzling and anti-aliasing in color mode, while enabling the display to remain live with the processor suspended;
  • LCD power Consumption: 0.1 Watt with backlight off; 0.2–1.0 Watt with backlight on.
  • The DCON - Display Controller chip with memory that enables the display to remain live with the processor suspended. The display and this chip are the basis of our extremely low power architecture. The machine is usable and relaying mesh networking traffic while the CPU and much of the motherboard is regularly turned off. The display controller chip also enables deswizzling and anti-aliasing in color mode. You can examine this photograph of the display (it looks even nicer in person; photographing a display is remarkably difficult).
Note: web browser images are currently scaled up so that an image of very roughly [800x600] fills up the browser window.
eToys (Squeak)running on the OLPC display

Integrated peripherals

Keyboard detail
  • Camera: integrated color video camera; 640 x 480 resolution at 30 FPS; independent (and undefeatable by software) display of microphone and camera recording status; the camera and device driver support disabling AGC and automatic color balancing, to enable its use as a photometric sensor for educational applications;
  • Wireless Networking: Integrated 802.11b/g (2.4GHz) interface; 802.11s (Mesh) networking supported; dual adjustable, rotating antennas support diversity reception; capable of mesh operation when CPU is powered down;
  • Status indicators: Power, battery, and WiFi (2), visible with lid open or closed; Microphone In-Use, and Camera In-Use, visible when lid is open.

External connectors

  • DC Power: 6mm (1.65mm center pin) connector; 11 to 18 V input usable, 40 to 40V input tolerated; power draw limited to 15 W;
  • Headphone output: 3.5mm 3-pin switched stereo audio jack;
  • Microphone input: 3.5mm 2-pin switched mono microphone jack; selectable 2V DC bias; selectable sensor-input mode (DC or AC coupled);
  • USB: Three Type-A USB 2.0 connectors; Up to 1A power supplied (total);
  • Flash Expansion: SD Card slot.
Connectors

Battery

  • Pack type: 2 or 4 cells LiFePO4; or 5 cells NiMH, approx. 6V series configuration (subject to change);
  • Capacity: 16.5 Watt-hours (NIMH), 22 Watt-hours (LiFeP);
  • Fully-enclosed “hard” case; user removable;
  • Electronics integrated with the pack provide:
    • Identification;
    • Battery charge and capacity information;
    • Thermal and over-current sensors along with cutoff switch to protect battery;
  • Minimum 2,000 charge/discharge cycles (to 50% capacity of new).
  • Power Management will be critical
Battery

BIOS/loader

  • Open Firmware (including hardware initialization and fast resume).

Environmental specifications

  • Temperature: UL certification planned to 45C in Q32007, pending 50C certification in mid-2008;
  • Humidity: UL certification planned to IP42 (perhaps higher) when closed, the unit should seal well enough that children walking to and from school need not fear rainstorms and dust;
  • Maximum altitude: –15m to 3048m (14.7 to 10.1 psia) (operating), –15m to 12192m (14.7 to 4.4 psia) (non-operating);
  • Shock 125g, 2ms, half-sine (operating) 200g, 2ms, half-sine (non-operating);
  • Random vibration: 0.75g zero-to-peak, 10Hz to 500Hz, 0.25 oct/min sweep rate (operating); 1.5g zero-to-peak, 10Hz to 500Hz, 0.5 oct/min sweep rate (nonoperating);
  • 2mm plastic walls (1.3mm is typical for most systems).

Regulatory requirements

  • The usual US and EU EMI/EMC (Electromagnetic Interference and Compatibility) requirements will be met;
  • The laptop meets IEC 60950-1, EN 60950-1, and CSA/UL 60950-1 specifications. It also complies with UL 1310 and UL 498. In order to guarantee the safety of children using the laptop, it also passes ASTM F 963;
  • The external power adapter complies with IEC, EN, and CSA/UL 60950-1
  • The removable battery pack complies with IEC, EN, and CSA/UL 60950-1 and UL 2054;
  • RoHS (Restriction of Hazardous Substances Directive – EU) compliant.

Support Hardware

Serial Adapter

  • 3.3V TTL to RS-232 Level shifter
    Serial Adapter

Laptop Development Schedule

The XO laptop hardware development schedule has two more test unit builds (Beta Test 3 and Beta Test 4), before a final test build (C Test 1) on the final production line and mass production. The Beta Test 3 build scheduled for early May will be the first one providing the processor and memory capabilities of the production version.

Pre-production Test Systems (CTest-1, or C1)

This build is of 300 laptops produced as a test of the manufacturing process on the main production line, and should happen starting August 6th, 2007. Slip resistance rubber feet will be added as will more easily replacable bunny ears (just two screws per ear after bezel removal). The hinge stop that appeared in B3/B4 will be eliminated or reduced (this is used to the stop the display at perpendicular before it tilts back further). Bean texture will be applied to the exterior white parts and "satin" texture to the the rest of the laptop plastic parts. A C1 laptop will be nearly identical to the production unit ...

Beta Test 4 Systems (BTest-4, or B4)

This build which ran from June 20-25, 2007, was the final chance to fix hardware and mechanical problems that were detected in the Beta Test 3 build of the XO. 2000 units were built.

Texture was added to the upper handle bar, the hinge tilt was increased by 7 degrees, the hinge "squeak" was eliminated, the rabbit ears click in place when put in the "down" position", the slight camera vignetting seen in B3 was eliminated, and minor modifications were made to the motherboard.

Beta Test 3 Systems (BTest-3, or B3)

This build, scheduled for May 2007, is the first to use an updated design for the laptop. Noticeable improvements over BTest-2 include:

  • A faster, lower power processor: the Geode LX-700
    • 64 KB I/64 KB D of L1 Cache, 128 KB of L2 Cache (vs. 32 KB of L1 cache)
    • Faster processor and memory clock (433/333 vs. 366/266)
    • 1.5 W typ. vs. 3 W typ.
    • Much better graphics processor, including support for rotated blits and depth conversion
  • More memory: 256 MB of SDRAM (vs. 128 MB)
  • extra screws
  • insert molded rubber ears for better robustness
  • a smaller battery cavity to improve robustness, make the bumper lines cleared
  • 10-20V input voltage tolerance.
  • new bumper tooling to allow the bumpers to be made of polycarbonate (as opposed to PC/ABS) with 3mm thickness and ribbing to 1.8mm (was 2mm and 1.2mm respectively)
  • colored XO on the back cover (400 different color combinations so kids can distinguish their laptops from each other
  • A keyboard that is much better to type on
  • Finally a touchpad that is much easier to use and much more responsive
  • a steel plate inside the entire keyboard base to reduce the feeling of flimsiness
  • a flipped USB connector so each side has the same way up for a USB key or device
  • A new hinge design allows greater tilt of the screen
  • An improved case design (addressing strength)

A very small number of BTest-3 units (around a hundred) were built, all were used for hardware and low level software development.

Beta Test 2 Systems (BTest-2, or B2)

Approximately 2500 systems were built by Quanta and are being distributed. These are fully functional machines with CaFE ASICs, and reflect some, but not all of the learning and improvements from testing of BTest-1. Much more information about the BTest-2 systems can be found in the BTest-2 Release Notes. Some of the details of the hardware design are to support the OLPC Human Interface Guidelines.

BTest-2 systems are almost identical visually with BTest-1. BTest-3 will have more substantial physical differences. An easy way to tell the difference between BTest-1 and BTest-2 is that BTest-1 keyboards have white lettering, and BTest-2 has black lettering.

There are two flavors of B2. B2-1 machines have 128MB memory. B2-2 have 256MB.

Beta Test 1 Systems (BTest-1)

Approximately 875 systems were built by Quanta and were distributed. These are fully functional machines, but built before the rigorous testing that will now take place. Much more information about the BTest-1 systems can be found in the BTest-1 Release Notes.

Pre-BTest boards

A small number of pre-BTest boards were built in preparation for building complete BTest systems. Developer information about B-test boards are here.

Alpha Test Prototype Electronics

Power up of the first OLPC electronics prototype boards occurred April 15, 2006. Power and ground testing continued over the weekend, and formal debug and BIOS bring up started Monday, April 17, 2006 at Quanta Computer's labs in Taipei, Taiwan. By Wednesday, April 19, Linux was booting on the first generation prototypes.

Photographs:


See also

Environmental Impact

Hardware

Support

Formerly part of this page:

Hardware uniqueness

Hardware design

School Server Hardware

While the laptop is rightfully at the center of OLPC, a valuable peripheral is the school server. OLPC will be building and distributing school servers along with the laptops, to extend the storage and computation provided by each laptop, as well as providing a local library and a mesh portal to the Internet.

Unlike the laptop, the school server is more of a collection of services than a hardware platform. In a manner identical to the laptop, OLPC will collaborate with manufacturing partners to provide a cost-efficient hardware platform for running the recommended software. Unlike the laptop, the manufacturing collaboration will not be exclusive. Individual countries will be free (even encouraged) to design and manufacture their own school servers running derivatives of the OLPC school server software.

XS

This will be the school server designed by OLPC. It is mostly designed, but currently on hold as we reconsider manufacturers, and should reach early production volumes in spring 2008. See the specification.

XSX

XSX limited-production prototype school server. The actual XS school servers won't look anything like this.

This is a prototype school server, built for early school trials in country. It will be integrated from off-the-shelf components, and will be overpowered compared to a production school server in order to simplify early demands for system software. See the specification and the implementation.