Hardware Drivers/lang-ko

From OLPC
Jump to navigation Jump to search
  번역근원 Hardware Drivers 원문  
  english | 한국어   +/- 차이  
  • 참고: 기술적인 자료의 번역을 위해 여러분의 도움을 기대합니다. www.laptop.org 사이트와 이 사이트의 메인 페이지들은 대부분 번역되었으나, 나머지는 한글 요약만을 제공하고 있습니다. 어느 페이지든 추가 번역이 필요하면, XO Korea의 번역 섹션에 메시지를 남겨 주시기 바라며, 모자라는 번역 부분을 채워주실 손길을 기다리고 있습니다.
  • Note: Some core pages have been fully translated, and others are provided with summaries. If you need more translation, please leave a message onto the discussion page of this, or that of XO Korea.


비디오

DCON

DCON은 자체 페이지가 있습니다: DCON.

FBDev 드라이버

The Geode GX Framebuffer (gxfb) driver is used in both LinuxBIOS and in the kernel proper during bootup. It provides simple unaccelerated framebuffer support and also helps drive the flatpanel.

Currently available in the olpc-2.6 GIT tree

You can change the resolution of the framebuffer two ways:

  • with the 'fbset' utility like so:
fbset -g <xres> <yres> <xres> <yres> <depth> -n
  • On the kernel command line:
 video=gxfb:<xres>-<yres>-<depth>@<refresh>

We have timings for all of the standard VESA modes, plus the special 1200x900 mode for the OLPC panel. Don't use the 1200x900 mode on a CRT - you could damage your monitor, or at the very least get a headache.

I spoke too soon. These fbdev mode works well on my multi-sync monitor. YMMV - use with caution, don't take internally, see your doctor if the symptoms don't go away, etc, etc.... JordanCrouse (Talk to me!) 14:57, 3 August 2006 (EDT)

mode "1200x900-75"
   # D: 124.239 MHz, H: 73.952 kHz, V: 75.002 Hz
   geometry
   timings
   rgba 5/11,6/5,5/0,0/0
endmode
mode "1200x900-85"
       # D: 132.767 MHz, H: 81.352 kHz, V: 85.008 Hz
       geometry
       timings
       accel false
       rgba 5/11,6/5,5/0,0/0
endmode

X 비디오 드라이버

The Geode GX/LX Xorg graphics driver is a Xorg driver that is under development. It provides XAA support for the Geode GX and LX, and EXA support for the GX. It also provides a simple Xv driver for the GX. It's packaged as xorg-x11-drv-amd in Fedora Core, and also available on freedesktop.org: GIT tree.

The following is an example "Device" entry to enable the driver:

Section "Device"
        Identifier "Geode"
        Driver "amd"
        
        # The following will enable the EXA driver.  Comment it to only use XAA
        Option "AccelMethod" "EXA"

        # This option disables VGA probing
        Option "NoVGA" "true"
 
        # The folloiwng tells the driver to use our custom mode (otherwise, it uses an internal table)
        # You will only want to use this if you have a DCON attached - the internal tables have most VESA modes
        Option "CustomMode" "true"

        # The following turns compression off - this allows the driver to use a linear pitch instead of a power of 2
        # Saving about 3MB of video memory for other uses 
        Option "NoCompression" "true"
EndSection

The following modeline should match the correct OLPC panel timings:

Mode "1200x900"
        DotClock 57.275
        HTimings
        VTimings
        Flags    "+HSync" "+VSync"
EndMode

Marvell 무선 드라이버

Is available in the GIT tree, but it would be great if it could be included in the next stream-image

메쉬 네트워킹

Are you going to place the RoofTop network driver in the box to enable mesh networking?

오디오

Note: need to verify that the audio sensor stuff actually made it upstream and come up with a test plan. Also need to document OLPC-specific bits.

CAFE NAND Driver

Is available in the GIT tree.