All public logs
Jump to navigation
Jump to search
Combined display of all available logs of OLPC. You can narrow down the view by selecting a log type, the username (case-sensitive), or the affected page (also case-sensitive).
- 19:42, 15 April 2010 Joemck talk contribs success (192.138.213.253)
- 21:44, 19 February 2009 Joemck talk contribs success (24.60.192.190)
- 08:25, 1 January 2008 Joemck talk contribs uploaded File:Touchpad-ribbon-cables-out.jpg (Disassembly of the bottom half of a mass-production G1G1 XO-1. Keyboard/touchpad controller with the touchpad cables unplugged. The clear flap on the end of each ribbon cable is helpful in plugging them back in.)
- 08:22, 1 January 2008 Joemck talk contribs uploaded File:Screws.jpg (Disassembly of the bottom half of a mass-production G1G1 XO-1. Photo showing the 4 kinds of screws used here. All are #1 philips head (or is that #0?).)
- 08:20, 1 January 2008 Joemck talk contribs uploaded File:Running-open.jpg (Disassembly of the bottom half of a mass-production G1G1 XO-1. Running the Open Firmware keyboard diagnostic with the bottom half of the XO taken apart. I was working on a stuck Ctrl key. The screen shows it stuck right now.)
- 08:16, 1 January 2008 Joemck talk contribs uploaded File:Magnet.jpg (Disassembly of the bottom half of a mass-production G1G1 XO-1. This lid-switch magnet falls out when you remove the left rail. Also, if you're using a (lightly!) magnetized screwdriver, you might want to use a different one for this screw, since the rotat)
- 08:13, 1 January 2008 Joemck talk contribs uploaded File:Left-rail-popped-off.jpg (Disassembly of the bottom half of a mass-production G1G1 XO-1. Removal of the left side rail, showing the two snap locations. I used the nail-clipper handle to slide in to undo the snaps.)
- 08:10, 1 January 2008 Joemck talk contribs uploaded File:Kbd-peel-back.jpg (Disassembly of the bottom half of a mass-production G1G1 XO-1. A look under the membrane in a corner of the keyboard. The rubber membrane just presses on a plastic membrane that's sealed onto a circuit board. This makes it more moisture- and dirt-resistan)
- 08:06, 1 January 2008 Joemck talk contribs uploaded File:Hinge-closeup.jpg (Disassembly of the bottom half of a mass-production G1G1 XO-1. Closeup of the hinge after unscrewing it from the base.)
- 08:05, 1 January 2008 Joemck talk contribs uploaded File:Handle-open.jpg (Disassembly of the bottom half of a mass-production G1G1 XO-1. After removing hinge cover, the top panel of the handle, the green bar along the top, and 4 screws. The remaining 6 screws don't appear to do anything.)
- 08:00, 1 January 2008 Joemck talk contribs uploaded File:Glue.jpg (Disassembly of the bottom half of a mass-production G1G1 XO-1. Strip of restick glue that holds down the cable from the touchpad/keyboard controller to the motherboard.)
- 07:58, 1 January 2008 Joemck talk contribs uploaded File:Small-screw-icon.jpg (Disassembly of the bottom half of a mass-production G1G1 XO-1. This icon points at the 4 holes that take the smallest kind of screw.)
- 07:56, 1 January 2008 Joemck talk contribs uploaded File:Kbd-tp-ctlr-top.jpg (Disassembly of the bottom half of a mass-production G1G1 XO-1. Top (relative to how you see it when you remove it) view of the keyboard/touchpad controller board. This side faces down when the XO is fully assembled. CN5 connects to the keyboard, CN2 and C)
- 07:52, 1 January 2008 Joemck talk contribs uploaded File:Kbd-tp-ctlr-bot.jpg (Disassembly of the bottom half of a mass-production G1G1 XO-1. Bottom (relative to how you see it when you remove it) view of the keyboard/touchpad controller board. This side faces up when the XO is fully assembled. The two buttons at the top of the pict)
- 07:50, 1 January 2008 Joemck talk contribs uploaded File:Kbd-top.jpg (Disassembly of the bottom half of a mass-production G1G1 XO-1. Top view of the keyboard.)
- 07:49, 1 January 2008 Joemck talk contribs uploaded File:Kbd-bot.jpg (Disassembly of the bottom half of a mass-production G1G1 XO-1. Bottom view of the keyboard.)
