User:Az990tony/edublog-beta-hw: Difference between revisions

From OLPC
Jump to navigation Jump to search
No edit summary
No edit summary
Line 53: Line 53:
made tighter by turning the blue-purple lever clockwise until it is snug against the
made tighter by turning the blue-purple lever clockwise until it is snug against the
processor.
processor.

[[ Image:Az990tony_IMG_4718.png | "Memory" ]] Install the DIMM.

There are four slots for memory, two yellow and two black.

Revision as of 23:24, 14 June 2008

The following system was built from parts purchased at [SWS Electronics and Computers ] a local computer parts store in Tucson, Arizona (USA).

  • [[ http://www.asus.com/products.aspx?l1=1&l2=1&l3=380&l4=0&model=1679&modelmenu=2 | V3-M2A690G barebones PC ]]
    • tower case
    • power supply
      • includes one black SATA power connection cable
    • [[ http://www.asus.com/products.aspx?modelmenu=1&model=1585&l1=3&l2=101&l3=496 | M2A-VM motherboard ]]
      • ATI SB600 RAID controller
      • ATI Radeon 1200 Graphics
      • 8 USB ports (four in front panel, four in back)
      • Multi-card reader SD/MMC/MiniSD/Compact Flash
      • One built-in NIC (1GbE gigabit ethernet)
      • includes one 18-inch red SATA connection cable
  • AMD Athlon64 X2 dual-core 2.3 Ghz processor with heatsink/fan
    • The AMD single-core Sempron might have also met the CPU requirement
  • Two extra NIC cards (PCI)
  • One DVD-RW drive, attached on primary IDE-Master
  • Two SATA drives, 160GB each.
  • One 2GB DIMM
  • One extra power-plug cable (converts white EIDE to black SATA power connector)
  • One extra 18-inch red SATA cable

Assembling the Parts Together

"computer parts" Here are the parts purchased.

I had purchased two extra red SATA cables, but then learned that one was already included with the Barebones PC. Also, had to go back to the store for an extra EIDE-to-SATA (white to black) power cable adapter. The screwdriver #2 (shown with red handle) is all that you need for tools.

"USA voltage 115" Slide voltage to 115.

"USA voltage 115" Remove side and front panels.

"Installing the CPU" Install the CPU.

Since this motherboard has an AM2 socket, we could have gone with either an AMD Sempron or Athlon64 X2. I chose the Athlon64 X2 which was more expensive, but runs faster.

Installation was tricky, and I watched some YouTube videos to see how others had done this. Basically, you raise the shiny lever (shown in the up position above), align the corner with the triangle on the chip with the triangle on the motherboard (it is the corner nearest the power supply in the picture above). Line up all the pins, and push down into place. If it didn't work, lift the CPU up, and try again. Once in place, move the shiny lever back down to snap everything in place. If you fail to do this step correctly, you might end up buying another CPU.

"Installing the fan" Install the heatsink fan.

The fan was also a bit tricky. There are two silver brackets. Align the fan so that the blue-purple level is away from the power supply. Put the fan on the processor, and snap in the bracket that is nearest the power supply. Turn the lever all the way to the left, push down on the fan, and attach the other bracket. This second bracket is then made tighter by turning the blue-purple lever clockwise until it is snug against the processor.

"Memory" Install the DIMM.

There are four slots for memory, two yellow and two black.