XO 1.5 B3: Difference between revisions

From OLPC
Jump to navigation Jump to search
No edit summary
 
(6 intermediate revisions by 2 users not shown)
Line 1: Line 1:
{{OLPC}}
{{OLPC}}
[[Hardware#XO_1.5_Laptop|XO-1.5 Laptop]] Beta test model 3 (B-Test 3), also known as B3.
[[Hardware#XO-1.5_Laptop|XO-1.5 Laptop]] Beta test model 3 (B-Test 3), also known as B3.


== Description ==
== Description ==


The B3 run was motherboards only. If placed in a case, they went into cases with the new (capacitive-only) touchpad. OLPC received fifteen of these in September, 2009.
The B3 run was motherboards only. If placed in a case, they went into cases with the new (capacitive-only) touchpad. OLPC received fifteen of these in September, 2009. Eventually there were less than ten, and they have been withdrawn, so this page is no longer relevant.


== Identification ==
== Identification ==
Line 15: Line 15:
The noticeable differences are:
The noticeable differences are:


* Motherboard revision E
* Only four of eight memory chips populated (512 MB).
* Only four of eight memory chips populated (512 MB).
* Large polymer (black) capacitors in the processor power supply instead of tantalum (yellow).
* Large polymer (black) capacitors in the processor power supply instead of tantalum (yellow).
Line 32: Line 33:
====Obtaining Firmware====
====Obtaining Firmware====


B3 motherboards require a release equal to or later than [http://dev.laptop.org/pub/firmware/q3a15b/ Q3A15B]. We currently suggest using [http://dev.laptop.org/pub/firmware/q3a16/ Q3A16].
B3 motherboards require a release equal to or later than Q3A15B. There is no current firmware release for B3. Current XO-1.5 firmware releases are not tested on B3.

Check the [[XO 1.5 EC dev changelog]] for information about the latest EC firmware (integrated into the above OFW releases).


====Upgrading Firmware====
====Upgrading Firmware====


See [[upgrading firmware]].
You can upgrade to a different version of firmware by downloading a new firmware image, then:

# Place the firmware image (.rom) on a USB stick
# Ensure that you have both a somewhat charged battery and a DC power source
# Boot the laptop, pressing the escape key ('X' in upper left hand corner of keyboard) within a few seconds after boot to enter [[Open Firmware]].
# Insert the USB stick containing the new firmware into a motherboard USB port
# Type:
flash u:\q3a15.rom

The flash command will fail if the laptop is not connected to external power or doesn't have a battery with reasonable charge inserted. There is a way to force the upgrade without meeting those requirements, but it is not recommended for regular use.


===Linux===
===Linux===


See [[release notes]].
We currently provide a Linux build based on Fedora 11, which allows easy switching between a Sugar and a Gnome desktop.

Linux may be installed on the internal microSD card, or on an external SD (or microSD) card. Once installed on a microSD card, it may be used in either the internal socket or the external port (using an adapter).

====Obtaining Linux====

The latest Linux image for the XO-1.5 is available as the highest numbered os in [http://dev.laptop.org/~cjb/f11-1.5/ http://dev.laptop.org/~cjb/f11-1.5/]. As of Nov. 12, this was OS40. Download the [http://dev.laptop.org/~cjb/f11-1.5/os40/os40.img.gz http://dev.laptop.org/~cjb/f11-1.5/os40/os40.img.gz] (for installing from Linux) or [http://dev.laptop.org/~cjb/f11-1.5/os40/os40.zd http://dev.laptop.org/~cjb/f11-1.5/os40/os40.zd] (for installing from OFW).

====Installing from OFW====

You will need the .zd version of the OS image. Download it, then:
# Place the image on a USB stick, and insert it into the XO-1.5 laptop's USB port.
# Boot the laptop, pressing the escape key ('X' in upper left hand corner of keyboard) within a few seconds after boot to enter [[Open Firmware]].
# To install onto the internal SD card, type:
fs-update u:\os40.zd

''Currently (using q3a15b), the device aliases are messed up. Type the following to install onto the internal SD card:''
devalias fsdisk /sd/disk@3:0
fs-update u:\os40.zd

To install an image onto the external SD card, you need to type:
devalias fsdisk /sd/disk@1:0
fs-update u:\os40.zd

====Installing from Linux====

=====On an XO-1=====
To install a Linux image onto an SD card inserted into an XO-1, you can run:
zcat os40.img.gz > /dev/mmcblk0

=====On an XO-1.5=====
This becomes a little more complicated on an XO-1.5, as there are two SD card slots and Linux doesn't name them consistently. If there are two SD cards found at boot time, the internal SD slot will be /dev/mmcblk0 and the external SD slot will be /dev/mmcblk1. Otherwise, the SD card found at boot will be named /dev/mmcblk0 and the second card inserted will be /dev/mmcblk1.

Assuming you boot from the internal SD card, the command to install a Linux image onto an SD card inserted in the external SD slot is:
zcat os40.img.gz > /dev/mmcblk1

If you have a Sandisk microSD card (provided in the internal SD slot of most B2 prototypes), you will probably want to write to it using this command instead (it greatly reduces the time required to write an image):
zcat os40.img.gz | dd obs=131072 of=/dev/mmcblk1


== Hardware Limitations ==
== Hardware Limitations ==


The currently known hardware problems are:
The currently known hardware problems are:

===Lid switch===
The lid switch is flaky at best, completely non-operational (lid always closed) at worst. Tracked as [http://dev.laptop.org/ticket/9911|ticket #9911]. This is fixed in versions of firmware later than Q3A25.


===Power Draw===
===Power Draw===
Line 112: Line 65:


If the SERIAL_ENABLE jumper is set, the camera in-use LED will remain lit. This will not be fixed ([http://dev.laptop.org/ticket/9385 Trac ticket #9385]).
If the SERIAL_ENABLE jumper is set, the camera in-use LED will remain lit. This will not be fixed ([http://dev.laptop.org/ticket/9385 Trac ticket #9385]).

==Software Limitations==

(Below list auto-sourced from [[F11_for_1.5/Known_Issues]])

{{:F11_for_1.5/Known_Issues}}


== Documentation ==
== Documentation ==

Latest revision as of 03:36, 22 August 2013

  This page is monitored by the OLPC team.

XO-1.5 Laptop Beta test model 3 (B-Test 3), also known as B3.

Description

The B3 run was motherboards only. If placed in a case, they went into cases with the new (capacitive-only) touchpad. OLPC received fifteen of these in September, 2009. Eventually there were less than ten, and they have been withdrawn, so this page is no longer relevant.

Identification

Almost the same as a B2 motherboard:

  • The motherboard has a daughtercard for the WLAN.
  • The motherboard has an internal SD slot

The noticeable differences are:

  • Motherboard revision E
  • Only four of eight memory chips populated (512 MB).
  • Large polymer (black) capacitors in the processor power supply instead of tantalum (yellow).
  • A hole on both sides of the WLAN slot (only on the right in B2).
  • Lots of missing small components next to the external SD slot (no support for +1.8V SD slot operation).

Photographs:

XO 1.5 B1 Annotated Motherboard.png

Software Support

Firmware

XO-1.5 use Q3xxx firmware releases. These will not work on an XO-1.

Obtaining Firmware

B3 motherboards require a release equal to or later than Q3A15B. There is no current firmware release for B3. Current XO-1.5 firmware releases are not tested on B3.

Upgrading Firmware

See upgrading firmware.

Linux

See release notes.

Hardware Limitations

The currently known hardware problems are:

Lid switch

The lid switch is flaky at best, completely non-operational (lid always closed) at worst. Tracked as #9911. This is fixed in versions of firmware later than Q3A25.

Power Draw

The DC power input on B3s may reach 34W when running firmware earlier than Q3E15. With later firmware, the power draw is still 29W. There is an ECO which restores the laptop power to a 25W limit which should be applied to most B3 motheboards (in time).

WLAN

The WLAN works fine, but requires motherboard ECOs to suspend/resume properly.

Serial Port

The processor serial port situation on XO-1.5 is not optimal, as it shares pins with the camera interface. There is a connector (J4) located on the upper left hand side of the motherboard for +3.3V RS-232 connection (see the pinout and the connector/jumper locations), but its use must be enabled using a jumper or a serial adapter wired correctly (pin 1 tied to GND through a 1K resistor.)

To use the serial port you will have to either short PR148 or short pins 1 and 3 on the SERIAL ENABLE jumper (JP1). PR148 is a large power resistor located near the processor serial port (see the XO-1.5 B2 connector locations). JP1 is located right behind the processor serial port. Be aware that there is a test pad located next to the jumper block that erroneously looks like the pin 1 indicator. Pins 1 and 3 are the two pins closest to the memory chips.

There is no need to disconnect the camera in order to use the serial port. However, any use of the camera while the serial port is enabled will generate constant spurious serial data and is not recommended.

If the SERIAL_ENABLE jumper is set, the camera in-use LED will remain lit. This will not be fixed (Trac ticket #9385).

Documentation

Supporting documentation for these boards are (in PDF):

Followed by

Preceded by

Retrieved from "http://wiki.laptop.org/mediawiki/index.php?title=XO_1.5_B3&oldid=291834"