Backlight replacement: Difference between revisions
Jump to navigation
Jump to search
(→Step 1) |
m (redundant with Disassembly top - redirected as per Wad's request) |
||
| (20 intermediate revisions by 5 users not shown) | |||
| Line 1: | Line 1: | ||
#REDIRECT [[Disassembly backlight]] |
|||
{{draft}} |
|||
{{TOCright}} |
|||
Replacing a backlight is a relatively simple task. To do so, you will need a standard #1 and #0 Phillips head screwdriver and something to hold screws in. (In a pinch, parts taken off the XO can serve as temporary containers) This repair can be done within 15 minutes, even with little experience. Begin by taking out the screen, as in [[Screen replacement]]. |
|||
<br> |
|||
<br> |
|||
[[image:screen_0.jpg|thumb|left|Before we begin]] |
|||
<br style="clear:both" /> |
|||
== Taking off the front panel == |
|||
=== Step 1 === |
|||
Open the laptop and flip the screen up. Rotate it a 90 degree angle as shown in the sequence below. |
|||
Next, remove the screws from the bottom of the screen - there are two on each side (right/left) of the XO, so make sure to get all four. |
|||
[[image:Screen_1a.jpg|thumb|left|Flip screen up]] [[image:Screen_1b.jpg|thumb|left|Rotate]] [[image:Screen_1c.jpg|thumb|left|Unscrew - remember, there are 4.]] |
|||
<br style="clear:both" /> |
|||
=== Step 2 === |
|||
Remove the two green panels from the side of the XO. Slide them upwards and lift them off as shown. |
|||
[[image:Screen_2a.jpg|thumb|left]] [[image:Screen_2b.jpg|thumb|left|Slide up]] [[image:Screen_2c.jpg|thumb|left|Lift off]] |
|||
<br style="clear:both" /> |
|||
=== Step 3 === |
|||
Finally, pull off the front panel. It is tabbed, so it can simply be pulled out. Pull the bottom out (where the screws came out), and gently slide the piece downwards and out. |
|||
[[image:Screen_3a.jpg|thumb|left]] [[image:Screen_3b.jpg|thumb|left]] |
|||
<br style="clear:both" /> |
|||
== Taking out the screen == |
|||
=== Step 1 === |
|||
To get the screen out, remove the four screws highlighted. |
|||
[[image:Screen_4a.jpg|thumb|left|Unscrew]] <br style="clear:both" /> |
|||
=== Step 2 === |
|||
Next, carefully slide the screen out, pulling the bottom out. '''Do not''' tug it or let go, as it will still be connected to the motherboard by two cables. |
|||
[[image:Screen_4b.jpg|thumb|left|Slide out gently]] [[image:Screen_4c.jpg|thumb|left]][[image:Screen_4d.jpg|thumb|left| Watch out for cables!]] |
|||
<br style="clear:both" /> |
|||
[[image:Screen_4e.jpg|thumb|left| Unhook the cable]] [[image:Screen_4f.jpg|thumb|left| Watch out for this little cable, too.]] [[image:Screen_4g.jpg|thumb|left| Good to go!]] |
|||
<br style="clear:both" /> |
|||
== Taking out the backlight == |
|||
=== Step 1 === |
|||
Disconnect the backlight from the display by removing the two screws shown below using a #0 Philips head screwdriver. |
|||
== Replacing the backlight == |
|||
=== Step 1 === |
|||
== Replacing the screen == |
|||
=== Step 1 === |
|||
Replace the screen by sliding the connection cables into place and clipping them back down (it is generally easier to clip the thinner one that has a longer tether first). Reseat the screen, making sure that it sits flat and that none of the spacers is gone. |
|||
[[image:Screen_5a.jpg|thumb|left| Clip little cable in]] [[image:Screen_5b.jpg|thumb|left| Clip big cable in]] |
|||
<br style="clear:both" /> |
|||
[[image:Screen_5c.jpg|thumb|left| Gently slide screen back in]] [[image:Screen_5d.jpg|thumb|left| The screws with the large heads (4) go back in]] |
|||
<br style="clear:both" /> |
|||
=== Step 2 === |
|||
Slide the front panel back on, making sure that it sits flat. Note that there are hooks on the side of the panel (highlighted in blue) that need to slide into place; pushing the top of the screen flat and sliding it upwards works well. |
|||
[[image:Screen_6a.jpg|thumb|left| Watch out for these hooks]] [[image:Screen_6b.jpg|thumb|left| The rest of the panel slides into place]] |
|||
<br style="clear:both" /> |
|||
=== Step 3 === |
|||
Slide the green side pieces back into place. Then, rotate the XO 90 degrees and put the remaining screws back. Don't forget that the screws go in on both sides (right/left). |
|||
[[image:Screen_7a.jpg|thumb|left]] [[image:Screen_7b.jpg|thumb|left| Side panels slide back in place]] [[image:Screen_7c.jpg|thumb|left| Almost there!]] |
|||
<br style="clear:both"> |
|||
[[image:Screen_7d.jpg|thumb|left| Rotate]] [[image:Screen_7e.jpg|thumb|left| Put screws (4) back in. ]] |
|||
<br style="clear:both" /> |
|||
And you're done! Yay! :D |
|||
Latest revision as of 17:03, 27 June 2008
Redirect to: