Making XO sensors/Making a Humidity Sensor: Difference between revisions

From OLPC
Jump to navigation Jump to search
(New page: <div style="font-size: 1.0em;" align=center> '''MAKING A HUMIDITY SENSOR'''</div> {| class="wikitable" |- | 400px | As shown in the picture (and as you did when m...)
 
No edit summary
 
(4 intermediate revisions by 2 users not shown)
Line 1: Line 1:
<div style="font-size: 1.0em;" align=center>
'''MAKING A HUMIDITY SENSOR'''</div>

{| class="wikitable"
{| class="wikitable"
|-
|-
| [[Image:Sensors001.jpg|400px]]
| [[Image:Humidity 01.jpg‎|400px]]
| As shown in the picture (and as you did when making a plug), tear the two ends of the wire apart to make a V shape, and use a Stripper to strip the top of the wire bare.
| As shown in the picture (and as you did when making a plug), tear the two ends of the wire apart to make a V shape, and use a Stripper to strip the top of the wire bare.
Slide on the X (heat-compressible rubber tubing) onto both ends of the wire as shown. Only one side is shown in the picture, but follow the same process for the other wire.
Slide on the X (heat-compressible rubber tubing) onto both ends of the wire as shown. Only one side is shown in the picture, but follow the same process for the other wire.
Next, use the soldering iron to connect the two ends of the wire to the sensor. This can be done by adding some solder to the two end contact points of the sensor and to the bare ends of the wire. Subsequently, join the two together as shown in the picture, and allow the solder to cool, solidify and thus connect.
Next, use the soldering iron to connect the two ends of the wire to the sensor. This can be done by adding some solder to the two end contact points of the sensor and to the bare ends of the wire. Subsequently, join the two together as shown in the picture, and allow the solder to cool, solidify and thus connect.
|-
|-
| [[Image:Humidity 02.JPG‎‎|400px]]
| <Insert the picture here>
| Next, slide the rubber tubing up the wire so that it completely covers the two contact points, and then use X (hot air) to compress the rubber tubing onto the wire.
| Next, slide the rubber tubing up the wire so that it completely covers the two contact points, and then use X (hot air) to compress the rubber tubing onto the wire.
|-
|-
| [[Image:Humidity 04.JPG‎|400px]]
| <picture here>
| '''A completed Humidity sensor!'''
| '''A completed Humidity sensor!'''
|}
|}

== Other sensor instructions ==
{{Special:PrefixIndex/Making_XO_sensors/}}

[[Category:XO sensors]]

Latest revision as of 17:14, 16 October 2009

Humidity 01.jpg As shown in the picture (and as you did when making a plug), tear the two ends of the wire apart to make a V shape, and use a Stripper to strip the top of the wire bare.

Slide on the X (heat-compressible rubber tubing) onto both ends of the wire as shown. Only one side is shown in the picture, but follow the same process for the other wire. Next, use the soldering iron to connect the two ends of the wire to the sensor. This can be done by adding some solder to the two end contact points of the sensor and to the bare ends of the wire. Subsequently, join the two together as shown in the picture, and allow the solder to cool, solidify and thus connect.

Humidity 02.JPG Next, slide the rubber tubing up the wire so that it completely covers the two contact points, and then use X (hot air) to compress the rubber tubing onto the wire.
Humidity 04.JPG A completed Humidity sensor!

Other sensor instructions

Retrieved from "http://wiki.laptop.org/mediawiki/index.php?title=Making_XO_sensors/Making_a_Humidity_Sensor&oldid=220929"